《BS-EN-725-9-1997.pdf》由会员分享，可在线阅读，更多相关《BS-EN-725-9-1997.pdf（10页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 725-9 : 1997 The Eu
2、ropean Standard EN 725-9 : 1997 has the status of a British Standard ICS 81.060.99 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Advanced technical ceramics Methods of test for ceramic powders Part 9. Determination of untamped bulk density Licensed Copy: sheffieldun sheffiel
3、dun, na, Tue Nov 07 06:16:04 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 725-9 : 1997 This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 July 1997 B
4、SI 1997 The following BSI references relate to the work on this standard: Committee reference RPI/13 Draft for comment 93/301338 DC ISBN 0 580 27909 X Amendments issued since publication Amd. No.DateText affected Committees responsible for this British Standard The preparation of this British Standa
5、rd was entrusted to Technical Committee RPI/13, Advanced technical ceramics, upon which the following bodies were represented: AEATechnology Aluminium Federation British Ceramic Research Ltd. British Industrial Ceramic Manufacturers Association Department of Trade and Industry (National Physical Lab
6、oratory) Flat Glass Manufacturers Association GAMBICA (BEAMA Ltd.) Institute of Refractories Engineers Ministry of Defence Refractories Association of Great Britain Society of British Aerospace Companies Ltd. University of Manchester Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:16:04 GM
7、T+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 725-9 : 1997 BSI 1997i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 725-93 Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:16:04 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii BSI 1997 BS EN 72
8、5-9 : 1997 National foreword This British Standard has been prepared by Technical Committee RPI/13 and is the English language version of EN 725-9 : 1997 Advanced technical ceramics Methods of test for ceramic powders Part 9: Determination of untamped bulk density, published by the European Committe
9、e for Standardization (CEN). EN 725-9 : 1997 was produced as a result of international discussions in which the United Kingdom took an active part. EN 725-9 : 1997 has been approved by CEN member bodies under the weighted voting procedures introduced in 1988 to coincide with the introduction of New
10、Approach Directives from the Commisssion of the European Community. NOTE. International and European Standards as well as overseas standards, are available from Customer Services, BSI, 389 Chiswick High Road, London, W4 4AL. Compliance with a British Standard does not of itself confer immunity from
11、legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an inside back cover and a back cover. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:16:04 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CEN Eur
12、opean Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 Copyright reserved to CEN members Ref. No. EN 725-9 : 1997 E EUROPEAN STANDARDEN 725-9 NORME EUROPE ENNE EUROPA ISCHE NORM March 1997
13、 ICS 81.060.99 Descriptors: Ceramics, powdery materials, bulk products, tests, determination, bulk density English version Advanced technical ceramics Methods of test for ceramic powders Part 9: Determination of untamped bulk density Ce ramiques techniques avance es Me thodes dessai pour poudres ce
14、ramiques Partie 9: De termination de la masse volumique apparente en vrac Hochleistungskeramik Pru fverfahren fu r keramische Pulver Teil 9: Bestimmung der Schu ttdichte This European Standard was approved by CEN on 1996-12-22. CEN members are bound to comply with the CEN/CENELEC Internal Regulation
15、s which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This Europea
16、n Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the nationa
17、l standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:16:04 GMT+00:00 2006, Uncontrolled Copy, (c)
18、 BSI Page 2 EN 725-9 : 1997 BSI 1997 Foreword This European Standard has been prepared by Technical Committee CEN/TC 184, Advanced technical ceramics, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identic
19、al text or by endorsement, at the latest by September 1997, and conflicting national standards shall be withdrawn at the latest by September 1997. EN 725 consists of 11 parts: Part 1 :Determination of impurities in alumina Part 2 :Determination of impurities in barium titanate (ENV) Part 3 :Determin
20、ation of oxygen content of non-oxides by thermal extraction Part 4 :Determination of oxygen content of non-oxides by XRF analysis (ENV) Part 5 :Determination of particle size distribution Part 6 :Determination of specific area Part 7 :Determination of absolute density Part 8 :Determination of tapped
21、 bulk density Part 9 :Determination of untamped bulk density Part 10 : Determination of compaction properties Part 11 : Determination of reactivity on sintering (ENV) According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to imple
22、ment this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Principle3 3Apparatus3 4Procedure4 5Expression of results4
23、 6Test report4 7Repeatability and reproducibility4 Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:16:04 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 725-9 : 1997 BSI 1997 Figure 1. Apparatus 1 Scope This part of EN 725 describes a method for the determination of the untamped bulk
24、density of ceramic powders. 2 Principle The mass of a known volume of the powder is determined after allowing it to fall freely into a stationary container, avoiding vibration. The untamped bulk density is expressed by division of this mass by the volume of the container. 3 Apparatus (see figure 1)
25、3.1 Stainless steel cylindrical container, of volume approximately 100 cm3and a diameter to height ratio of 1. 3.2 24 mesh (710 mm) sieve, with a typical diameter of 80 mm. 3.3 Balance, with a precision of 0,01 g. 3.4 Tray, to collect the powder during the filling of the container. Licensed Copy: sh
26、effieldun sheffieldun, na, Tue Nov 07 06:16:04 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 725-9 : 1997 BSI 1997 3.5 Suitable apparatus for the powder sieve assembly, including a fixing system for the sieve with a cone in its lower part to allow the sieve and the cone to be set to a predete
27、rmined height above the top level of the cylindrical container (see 3.1), and an electric system to regulate the vibration of the sieve. 4 Procedure 4.1 Sample treatment If there is any treatment of the sample of powder before measurement (e.g. drying), this shall be recorded in the test report. 4.2
28、 Measurement Weigh the cylindrical container (see 3.1). Set the cylindrical container in the tray (see 3.4) so that its axis coincides with that of the cone, with the level of the sieve at a height of 190 mm above the cylindrical container top. Fill the sieve with the sample. If necessary start the
29、vibration system (see 3.5) and regulate it to allow the powder to flow evenly. Fill the cylindrical container in between 20 s and 30 s. Stop the feed when the powder has formed a cone above the top of the cylindrical container and is spilling over. Remove the cone of surplus powder by gently drawing
30、 a straight edge across the top rim of the cylindrical container, without communicating any vibration to the latter. Weigh the cylindrical container and its contents. 5 Expression of results The untamped bulk density rbis given by the formula rb= m12 m0 V where mois the mass, in grams, of the empty
31、cylindrical container; m1is the mass, in grams, of the cylindrical container full of powder; Vis the volume, in cubic centimetres, of the cylindrical container. Calculate the density in grams per cubic centimetre and then convert the answer to kilograms per cubic metre, to the nearest 5 kg/m3. 6 Tes
32、t report The test report shall include the following information: a) the name of the testing establishment; b) date of the test, report identification and number, operator, signatory; c) a reference to this standard, i.e. determined in accordance with EN 725-9; d) a description of the powder (materi
33、al type, manufacturer code, batch or code number); e) any pre-treatment of the powder such as drying; f) the results; g) any unusual features noted during the determination; h) any comments about the test or test results. 7 Repeatability and reproducibility The experience of three laboratories indic
34、ates that the method is capable, for an alumina powder with an untamped bulk density of 909 kg/m3, of achieving: a) a standard deviation of repeatability of 7 kg/m3; b) a standard deviation of reproducibility of 9 kg/m3. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:16:04 GMT+00:00 2006,
35、 Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:16:04 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
36、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe a
37、nd at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products
38、and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers member
39、s an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
40、In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards
41、 through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date
42、 with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in
43、 the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise witho
44、ut prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permissi
45、on of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:16:04 GMT+00:00 2006, Uncontrolled Copy, (c) BSI