《BS-ISO-1268-7-2001.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-1268-7-2001.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 1268-7: 2001 Fibre-reinforced plastics Methods of producing test plates Part 7: Resin transfer moulding ICS 83.120 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:31 GMT+00:00 2006, Uncontroll
2、ed Copy, (c) BSI BS ISO 1268-7:2001 This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 August 2001 BSI 08-2001 ISBN 0 580 37962 0 National forewo
3、rd This British Standard reproduces verbatim ISO 1268-7:2001 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: A list of organizati
4、ons represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence
5、 Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itsel
6、f confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and pr
7、omulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publicat
8、ion Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARD ISO 1268-7 First edition 2001-05-01 Reference number ISO 1268-7:2001(E) Fibre-reinforced plastics Methods of producing test plates Part 7: Resin
9、 transfer moulding Plastiques renforcs de fibres Mthodes de fabrication de plaques dessai Partie 7: Moulage par transfert de rsine Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:1
10、2:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-7:2001(E) diii ContentsPage 1Scope .1 2Normative references .1 3Health and safety 1 4Principle 1 5Materials .2 6Plate dimensions 2 7Reinforcement content .2 8Apparatus .2 9Procedure .3 10Verification of the characteristics of the plate obtaine
11、d 4 11Marking .4 12Test plate preparation report 5 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-7:2001(E) iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
12、 (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations,
13、governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/
14、IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some o
15、f the elements of this part of ISO 1268 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 1268-7 was prepared by Technical Committee ISO/TC 61,Plastics, Subcommittee SC 13,Composites and reinforcement fibr
16、es. Together with the other parts (see below), this part of ISO 1268 cancels and replaces ISO 1268:1974, which has been technically revised. ISO 1268 consists of the following parts, under the general titleFibre-reinforced plastics Methods of producing test plates: Part 1: General conditions Part 2:
17、 Contact and spray-up moulding Part 3: Wet compression moulding Part 4: Moulding of prepregs Part 5: Filament winding Part 6: Pultrusion moulding Part 7: Resin transfer moulding Part 8: Compression moulding of SMC and BMC Part 9: Moulding of GMT/STC The following additional parts are in preparation:
18、 Part 10: Injection moulding of SMC and BMC General principles and moulding of multipurpose test specimens Part 11: Injection moulding of SMC and BMC Small plates Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARDISO 1268
19、-7:2001(E) ISO 1002 All rithgs rreseved 1 Fibre-reinforced plastics Methods of producing test plates Part 7: Resin transfer moulding 1Scope This part of ISO 1268 specifies a method of preparing reinforced-plastic test plates by resin transfer moulding (RTM). It is intended to be read in conjunction
20、with ISO 1268-1. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 1268. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties
21、 to agreements based on this part of ISO 1268 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain regis
22、ters of currently valid International Standards. ISO 1172:1996,Textile-glass-reinforced plastics Prepregs, moulding compounds and laminates Determination of the textile-glass and mineral-filler content Calcination methods. ISO 1183 (all parts),Plastics Methods for determining the density of non-cell
23、ular plastics. ISO 1268-1,Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions. ISO 7822:1990,Textile glass reinforced plastics Determination of void content Loss on ignition, mechanical disintegration and statistical counting methods. ISO 11357-2:1999,Plastics Diffe
24、rential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature. ISO 11357-5:1999,Plastics Differential scanning calorimetry (DSC) Part 5: Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of conversion. 3Health and safety
25、 See ISO 1268-1. 4Principle Resin transfer moulding (RTM) is a low-pressure fabrication method carried out in a closed mould. The fibre reinforcement may be preformed. The reinforcement is placed in the cavity of the mould and the mould is closed. The resin system is injected into the cavity to impr
26、egnate the reinforcement. Subsequently, the resin is cured to form a composite plate. The procedure can be modifed, for instance by applying a vacuum to extract the air prior to resin injection, heating the resin to reduce its viscosity and curing time or, when the resin is a highly reactive one, in
27、troducing the resin and hardener separately, using two pumps, into a mixing chamber and then into the mould. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-7:2001(E) 2 5Materials 5.1Reinforcement Reinforcement fibres, such as glass
28、, carbon, aramid, etc., in the form of mats (chopped-strand or continuous-strand mats), chopped rovings, woven fabrics, knitted fabrics, braids, unidirectional reinforcements and combinations thereof can be used. The reinforcement may be preshaped into a preform in such a way that it retains its sha
29、pe. Preforms can be fabricated by spraying binder on to the assembled reinforcement and subsequently heat-setting. Alternatively, ordinary reinforcements can be converted into preforms by sewing, stitching or knitting them together using auxiliary yarns. The reinforcement shall be such that it can b
30、e easily placed in the mould cavity and impregnated with resin. Injection of the resin shall not cause the reinforcement to move. 5.2Resin The viscosity and cure characteristics of the resin shall be such that the mould cavity is properly filled and the reinforcement properly wetted prior to curing.
31、 6Plate dimensions The length and width of the plate produced shall be large enough to yield test specimens of the correct size for testing. The size of the test specimens shall conform to the relevant International Standards. A length and a width of are recommended. The thickness shall beto. Plates
32、 overthick are generally not suitable for use in the determination of mechanical properties. 7Reinforcement content For randomly oriented products, it is recommended that the fibre content be in the rangetoby volume. For woven products, the recommended range istoby volume. For unidirectional product
33、s, the recommended range istoby volume. 8Apparatus 8.1Mould, made of steel, aluminium or fibre-reinforced plastic, and composed of a male mould plate and a female mould plate with a cavity between them. An inlet for the resin and an outlet for the air (optional) are provided on the mould. The mould
34、shall be fitted with bolts or other secure fasteners to enable it to be closed tightly. Rubber packing is usually placed between the mould plates. Temperature-measurement devices may also be inserted in the mould plates. The surfaces of the mould plates shall be coated with release agent. 8.2Press w
35、ith heated platens, the temperature of which can be controlled to withinand the pressure to withinof the specified values. 8.3Air-circulation oven, the temperature of which can be controlled to within. 8.4Resin tanks, the temperature of which can be regulated. 8.5Pump, capable of transferring resin
36、atmaximum. 8.6Vacuum pump or vacuum source (optional). 300 mm1 mm4 mm4 mm 15 %30 % 35 %55 % 40 %60 % 5 C 20 kPa 5 C 800 kPa Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-7:2001(E) d3 8.7Flexible tubing, to connect the mould with t
37、he resin pump or vacuum source. 8.8Temperature and pressure control and recording equipment. 9Procedure 9.1Preparation of preform 9.1.1Examples of methods of producing preforms Sheets of mat are cut and plied to shape in accordance with the instructions. A small amount of polymeric binder is applied
38、. The stacked mat is then heated and compressed in a forming die. Reinforcement fibre is chopped and sprayed onto a rotating screen where they are kept in place by air suction. A small amount (to) of polymeric binder is added to the stream of chopped reinforcement. The chopped reinforcement is then
39、heated (sometimes in a forming die). Continuous fibres and/or woven fabrics may be added to the random-fibre mats produced in the previous method before heat-setting. Sheets of woven fabric are cut and stacked in a predetermined orientation. The stacked fabrics are sewn, stitched or knitted together
40、 using auxiliary yarns made, for instance, of polyamide, polyester, aramid, glass or carbon fibre. Unidirectional fabrics are used to provide preforms for high-fibre-content plates. Three-dimensional fabrics of a shape specific to a particular moulding are prepared by weaving, knitting or braiding.
41、9.1.2The mass per surface area of the preform shall be such that the plates produced have the required fibre content by volume. 9.1.3The preform design shall be such that it matches the shape of the mould and correct alignment of the fibres is maintained. 9.2Resin injection and cure 9.2.1Depending o
42、n the nature of the resin and reinforcement, different procedures may be required, examples of which are given in 9.2.2 to 9.2.4. 9.2.2Place the reinforcement in the cavity of the mould. Close the mould and clamp it shut with the bolts or other secure fasteners. Connect the mould to the resin pump a
43、nd resin tank with flexible tubing. Inject resin into the cavity by means of the pump. When the cavity is full, place the mould between the heated platens of a press or in a hot-air oven to cure the resin. 9.2.3Place the reinforcement in the cavity of the mould, close the mould and clamp it shut. Co
44、nnect the mould to a vacuum pump, and to the resin pump and resin tank, with flexible tubing. Apply a vacuum to extract the air. Transfer resin from the resin tank to the cavity through the tubing under atmospheric pressure, or slightly higher than atmospheric pressure, by means of the resin pump. 9
45、.2.4The injection-moulding process can also be used with highly reactive resins. Place the preform in the mould cavity, close the mould and clamp it shut. Inject the resin and hardener from two separate tanks into a mixing chamber and then inject the mixture into the mould. In this method, the flow
46、rate of the resin has to be high, which can cause movement of the reinforcement in the cavity. It is recommended that a check be carried out to ensure that the reinforcement does not move during injection. 9.2.5For all methods, record the temperature, pressure, duration under pressure and cure time.
47、 9.3Stabilization On completion of curing, open the mould and remove the test plate. When required by the material specification or the manufacturing method, the plate shall be postcured. Unless otherwise specified, it is recommended that all plates 2 %5 % Licensed Copy: sheffieldun sheffieldun, na,
48、 Mon Nov 27 08:12:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-7:2001(E) 4 be conditioned forin the atmosphere of the test laboratory before cutting out test specimens. It is also recommended that at leastbe discarded from the plate edges since the fibre content and fibre alignment is like
49、ly to be non-representative in this area. 10Verification of the characteristics of the plate obtained 10.1General The plate obtained shall be examined prior to cutting out the test specimens. The criteria used for acceptance or rejection of a plate shall be as given in the material specification or as agreed between the interested parties, taking into account the requirements given in 10.2 to 10.7. 10.2Fibre content The fibre content shall be determined in accordance with ISO 1172 for glass-reinforced plastics and