《ETSI EN-30011301-2-2006-DRAFT.pdf》由会员分享，可在线阅读，更多相关《ETSI EN-30011301-2-2006-DRAFT.pdf（19页珍藏版）》请在三一文库上搜索。
1、 Draft ETSI EN 300 113-2 V1.4.1 (2006-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envel
2、ope modulation and having an antenna connector; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the
3、 ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which
4、are, or may be, or may become, essential to the present document. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry
5、 phase of the ETSI standards Two-step Approval Procedure. The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC 4 (as amended) laying down a procedure for the provision of information in the field of technical sta
6、ndards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC 1 of the European Parliament and of the Council of 9 March 1999 on radio equipmen
7、t and telecommunications terminal equipment and the mutual recognition of their conformity (“the R Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector, as identified below: Part
8、1: “Technical characteristics and methods of measurement“; Part 2: “Harmonized EN covering essential requirements under article 3.2 of the R mobile station (equipment fitted with an antenna socket, normally used in a vehicle or as a transportable); and those hand portable stations: a) fitted with an
9、 antenna socket; or b) without an external antenna socket (integral antenna equipment), but fitted with a permanent internal or a temporary internal 50 Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input. Hand portable equipment without an external or
10、internal RF connector and without the possibility of having a temporary internal 50 RF connector is not covered by the present document. The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R Land mobile service; Radio equipment intended for the transmissio
11、n of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement“. 3 ETSI TR 100 028 (all parts) (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the m
12、easurement of mobile radio equipment characteristics“. 4 Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. . 5 ETSI EG 201 399 (V2.1.1): “Electromagnetic compa
13、tibility and Radio spectrum Matters (ERM); A guide to the production of candidate Harmonized Standards for application under the R the value of the measurement uncertainty for the measurement of each parameter shall be included in the test report; the value of the measurement uncertainty shall be, f
14、or each measurement, equal to or lower than the figures in table 1. For the test methods, according to the present document, the measurement uncertainty figures shall be calculated in accordance with TR 100 028 3 and shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which
15、provide confidence levels of respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties are normal (Gaussian). Table 1 is based on such expansion factors. The particular expansion factor used for the evaluation of the measurement uncertainty
16、 shall be stated. ETSI Draft ETSI EN 300 113-2 V1.4.1 (2006-08) 13 Table 1: Absolute measurement uncertainties: maximum values Parameter Uncertainty Radio Frequency 1 x 10-7 RF Power, conducted (up to 160 W) 0,75 dB Radiated RF power 6 dB Adjacent channel power 5 dB Sensitivity 3 dB Two-signal measu
17、rement, valid up to 4 GHz 4 dB Three-signal measurement 3 dB Conducted spurious emission of transmitter, valid up to 12,75 GHz 4 dB Conducted spurious emission of receiver, valid up to 12,75 GHz 3 dB Radiated emission of the transmitter, valid up to 4 GHz 6 dB Radiated emission of receiver, valid up
18、 to 4 GHz 6 dB Transmitter transient frequency (frequency difference) Transmitter transient time 250 Hz 20 % Temperature 1 K Humidity 10 % NOTE: Values valid up to 1 GHz for the RF parameters unless otherwise stated. 5.3 Essential radio test suites Essential test suites are referred to in annex III
19、of R - it provides a statement of all the test procedure corresponding to those essential requirements by cross reference to specific clause(s) in the present document or to a specific clause(s) in specific referenced document(s); - it qualifies each requirement to be either: Unconditional - meaning
20、 that the requirement applies in all circumstances; or Conditional - meaning that the requirement is dependent on the supplier having chosen to support optional functionality defined within the schedule; - in the case of Conditional requirements, it associates the requirement with the particular opt
21、ional service or functionality; - it qualifies each test procedure to be either: Essential: meaning that it is included with the Essential Radio Test Suite and therefore the requirement shall be demonstrated to be met in accordance with the referenced procedures; Other: meaning that the test procedu
22、re is illustrative but other means of demonstrating compliance with the requirement are permitted; - when the schedule is completed in respect of a particular equipment including the testing outcomes, including a completed version of Table A1 it provides a means to assert the “presumption of conform
23、ity“ with the HS. ETSI Draft ETSI EN 300 113-2 V1.4.1 (2006-08) 16 Table A.1: HS Requirements those designated “O“ make up the Other Test Suite; for those designated “X“ there is no test specified corresponding to the technical requirements. All tests classified “E“ shall be performed as specified w
24、ith satisfactory outcomes is a necessary condition for a presumption of conformity. Technical requirements associated with tests classified “O“ or “X“ must be complied with as a necessary condition for presumption of conformity, although conformance with the requirement may be claimed by an equivale
25、nt test or by manufacturers assertion supported by appropriate entries in the technical construction file. Reference: Clause Number Identification of clause(s) defining the test specification in the present, document unless another document is referenced explicitly. Where no test is specified (that
26、is, where the previous field is “X“) this field remains blank. ETSI Draft ETSI EN 300 113-2 V1.4.1 (2006-08) 18 Annex B (informative): The EN title in the official languages Language EN title Czech Danish Dutch English Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile servi
27、ce; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive Estonian Finnish French German Greek Hungarian
28、Icelandic Italian Latvian Lithuanian Maltese Norwegian Polish Portuguese Slovak Slovenian Spanish Swedish ETSI Draft ETSI EN 300 113-2 V1.4.1 (2006-08) 19 History Document history V1.1.1 March 2001 Publication V1.2.1 April 2002 Publication V1.3.1 December 2003 Publication V1.4.1 August 2006 Public Enquiry PE 20061208: 2006-08-09 to 2006-12-08