《ECA-EIA-704-1-2002.pdf》由会员分享，可在线阅读，更多相关《ECA-EIA-704-1-2002.pdf（11页珍藏版）》请在三一文库上搜索。
1、P EIA STANDARD Adhesively-Sealed Component Packaging EIA-704-1 (Addendum No. 1 to EIA-704 - Previously EIABS-704-1) JUNE 2002 Electronic Components, Assemblies & Materials Associatlon ELECTRONIC COMPONENTS, ASSEMBLIES & MATERIALS ASSOCIATION THE ELECTRONIC COMPONENT SECTOR OF THE ELECTRONIC INDUSTRI
2、ES ALLIANCE Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS -,-,- NOTICE EIA Enginee
3、ring Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper prod
4、uct for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of E L A from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude t
5、heir voluntary use by those other than EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, EL4 does not assume any liab
6、ility to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is considered to have Intemational Standardization implication, but the International Electrotechnical Commission activity has not progressed to the point where a
7、valid comparison between the EM Standard and the IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health
8、 practices and to determine the applicability of regulatory limitations before its use. (From Project Number 5010, formulated under the cognizance of the Automated Component Handling (ACH) Committee.) Published by ELECTRONIC INDUSTRIES ALLIANCE 1996 Technology Strategy & Standards Department 2500 Wi
9、lson Boulevard Arlington, VA 22201 PRICE: Please refer to the current Catalog of EIA Electronic Industries Alliance Standards and Engineering Publications or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) All rights reserved Printed in U.S.A. Copyrigh
10、t Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS -,-,- PLEASE! This document is copyrighted b
11、y the EL4 and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 801 12-5704 or call U.S.A. and Can
12、ada 1-800-854-7179, International (303) 397-7956 Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without lice
13、nse from IHS -,-,- EIA-704- 1 Adhesively-Sealed Component Packaging Clause Page 1 Scope 2 Introduction “ 3 Requirements Figure 1 Adhesively-Sealed Carrier Configuration 2 Side or Front View 3 4 Top View: Component Rotation 5 - Top View: Component Lateral Movement Adhesively-Sealed Tape Leader & Trai
14、ler Dimensions “ i Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS -,-,- EU-704- 1 T
15、his page intentionaily lefi blank ii Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS
16、 -,-,- EIA-704- 1 Page 1 Adhesively-Sealed Component Packaging 1 Scope This addendum to Standard 704 provides requirements for packaging components for automatic handling using adhesively-sealed cover tape and carrier tape. 2 Introduction This addendum was formulated to provide materials and process
17、es necessary to package components such that they may be automatically handled. 3 Requirements The cover tape shd have a total peel strength of ftom 0.1 N to 1.5 N (10 grams to 150 grams calibrated scale reading) for 72 mm through 200 mm wide carrier tapes. The direction of pull shali be opposite th
18、e direction of carrier tape travel such that the carrier tape makes an angle of between 165 and 180 degrees with the top of the cover tape. The separation of the cover tape from carrier tape shall occur at a rate of 300 d m i n u t e f 10 dminute during peeling (see Standard 704 subclause 4.2 (d). C
19、opyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS -,-,- EIA-704- 1 Page 2 Fig u re 1 .
20、Adhesively-Sealed Carrier Configuration (E, is for tape feeder reference only. conceniric about Bo. See Noie 3. Table I.) Holes Note 1 The cover Pa (10 pitches cumulailve folerance on iape f0.2 mm) 1 Do - 1 User Direction of Unreellng Bar Code Label Area Elongalsd Sprocket Holes ape shall not extend
21、 over the edge of the sprocket holes nor cover any part of them. Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permit
22、ted without license from IHS -,-,- ELA-704- 1 Page 3 Figure 2. Side or Front View 5 Maximum Figure 3. Top View: Component Lateral Movement Top of Carrier 1 mm, maximum F 4 b t mm, maximum Figure 4. Top View: Component Rotation lo, maximum Typ Ca I Com pon en t Cente rlin e Typical Component Cavity C
23、enterline Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS -,-,- EIA-704- 1 Page 4 Fi
24、gure 5. Ad hesively-Sealed Tape Leader 8 c Trailer Dimensions Leoder. 390 mm, Min. See Note 1 NOTES l., There shall be a leader of 230 mm minimum which may consist of carrier and/or cover tape followed by a minimum of 160 m m of empty carrier tape sealed with cover tape. 2. There shall be a trailer
25、of 160 mm minimum of empty carrier tape sealed with cover tape. The entire carrier tape must release from the reel hub when the last portion of the tape unwinds from the reel without damage to the carrier tape and the remaining components in the cavities. Copyright Electronic Components, Assemblies
26、& Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS -,-,- EIA Document Improvement Proposal Document No. Submitters Name: If in the
27、review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Document Title: Telephone No.: FAXNo.: e-mail: Electronic Industries Alliance Technology Strategy & Standards Department -
28、Publications Office 2500 Wilson Blvd. Arlington, VA 22201 FAX: (703) 907-7501 Signature: Date: Urgency of Change: Immediate: 0 At next revision: Problem Area: a. Clause Number and/or Drawing: b. Recommended Changes: c. ReasodRationale for Recommendation: Additional Remarks: Chairman: Date comments f
29、orwarded to Committee Chairman: Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS -,-,
30、- Electronlc Industrles Alllance Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 20:00:34 MDTNo reproduction or networking permitted without license from IHS -,-,-