《ECA-EIA-364-68A-2001.pdf》由会员分享，可在线阅读，更多相关《ECA-EIA-364-68A-2001.pdf（14页珍藏版）》请在三一文库上搜索。
1、i m Y ANSUEIA-3 64-68A-200 1 Approved: April 10,2001 EIA STANDARD TP-68A Actuating Mechanism Test Procedure for Electrical Connectors EIA-364-68A (Revision of EU-364-68) APRIL 2001 ELECTRONIC COMPONENTS, ASSEMBLIES see figure 1 for example force details. The force shall be applied in each of the fol
2、lowing directions. - Fal/Fa2 perpendicular to the actuator axis and in the plane of the actuator travel and at each end position of the actuator; - Fbl/Fb2 perpendicular to the actuator axis and perpendicular to the plane of actuator travel at each end position of the lever; axially with the lever a
3、xis towards the lever pivot; and axially with the lever axis away from the lever pivot. - Fc - Fd 4. .2 The force shall be steadily increased at a rate of approximately 20 N/s (, 50 lb/s) up to the specified value and maintained for 1 minute unless otherwise specified in the referencing document. 4.
4、2 Torque A specified torque shall be applied around the axis of the lever in either direction for 1 minute, unless otherwise specified in the referencing document. 5 Details to be specified The following details shall be specified in the referencing document: 5.1 Mounting details 5.2 Shape of the fi
5、xture or tool for the application of the forcekorque 5.3 Forcekorque to be applied, direction and rate of application 5.4 Requirements for final measurements 5.5 Any deviation from this standard Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with EC
6、A Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 02:56:48 MDTNo reproduction or networking permitted without license from IHS -,-,- EN-3 64-68A Page 3 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the fol
7、lowing: 6.1 Title of test 6.2 Specimen description 6.3 Test equipment used, and date of last and next calibration 6.4 Test and procedure 6.5 Values and observations 6.6 Name of operator and date of test Fd Lever pivot point Side view i w l Actuating lever axis I End view i Figure 1 Details of force
8、application Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 02:56:48 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright Electron
9、ic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 02:56:48 MDTNo reproduction or networking permitted without license from IHS -,-,- EIA Document Improvement Proposal If in the revi
10、ew or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Industries Alliance 2500 Wilson Blvd. Arlington, VA 2220 1 Technology Strategy & Standards Publications Office FAX:
11、(703) 907-7501 Document No. Document Title: Submitter s Name: Telephone No. : FAXNo.: e -mail : I Address: Urgency of Change: Immediate: 0 At next revision: 0 Problem Area: a. Clause Number andor Drawing: b. Recommended Changes: c. ReasodRationale for Recommendation: Additional Remarks: Signature :
12、Date: FOR EIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 02:56:48 M
13、DTNo reproduction or networking permitted without license from IHS -,-,- Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 02:56:48 MDTNo reproduction or networkin
14、g permitted without license from IHS -,-,- Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 02:56:48 MDTNo reproduction or networking permitted without license fr
15、om IHS -,-,- Electronic Industries Alliance Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 02:56:48 MDTNo reproduction or networking permitted without license from IHS -,-,-