《ECA-EIA-364-62A-2004.pdf》由会员分享，可在线阅读，更多相关《ECA-EIA-364-62A-2004.pdf（12页珍藏版）》请在三一文库上搜索。
1、ANSVEIA 364-62A-2004 Approved: July 19, 2004 EIA STANDARD TP-62A TERMINAL STRENGTH TEST PROCEDURE FOR ELECTRICAL CONNECTORS, AND SOCKETS EIA-364-62A (Revision of EIA-364-62) July 2004 E i i Electronic Components, Assemblies 1 cycle constitutes moving one direction in the same plane from the original
2、 position and then returning to the original position. 4.1.2 If the terminals are not capable of being bent with the fingers, or if the method of bending is critical, the individual specification shall specifi the method of bending and any fixture required to control the point of application. Copyri
3、ght Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 19:55:15 MDTNo reproduction or networking permitted without license from IHS -,-,- EIA-364-62A Page 2 4.2 Solderless wr
4、ap terminals (torque and bending) 4.2.1 A torque of 0.014 newton-meter (2.0 ounce-inches) shall be applied clockwise and then counterclockwise in a plane perpendicular to the axis of the terminal. The force shall be applied gradually to the terminal and then maintained for a period of 5 seconds to 1
5、5 seconds. 4.2.2 At completion of the torque test the specimens shall be subjected to the bending test as described in 4.1. 5 Details to be specified The following details shall be specified in the referencing document: 5.1 Applicable tests 5.2 Method of bending and fixture required, if critical 5.3
6、 Number of terminations to be tested 5.4 Number of bends if other than 2 5.5 Any deviation from the standard test method 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description 6.3 Test equ
7、ipment used, and date of last and next calibration 6.4 Test and procedure and sequence 6.5 Values and observations 6.6 Name of operator and date of test Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=
8、Wing, Bernie Not for Resale, 03/30/2007 19:55:15 MDTNo reproduction or networking permitted without license from IHS -,-,- EIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the approp
9、riate information below and mail or FAX to: Electronic Industries Alliance Technology Strategy & Standards Department - Publications Office 2500 Wilson Blvd. Arlington, VA 22201 FAX: (703-875-8906) Document No. Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: I Urgency of Ch
10、ange: Immediate: n At next revision: II Problem Area: a. Clause Number and/or Drawing: b. Recommended Changes: c. ReasodRationale for Recommendation: Additional Remarks: Signature: Date: FOR EIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Copyright Electr
11、onic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 19:55:15 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright Electronic Components, Assemblies &
12、Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 19:55:15 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright Electronic Components, Assemblies & Materials Association Provided
13、 by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 19:55:15 MDTNo reproduction or networking permitted without license from IHS -,-,- EkCtrOnk Industries Alliance Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 19:55:15 MDTNo reproduction or networking permitted without license from IHS -,-,-