《ECA-580A0AC-1998.pdf》由会员分享,可在线阅读,更多相关《ECA-580A0AC-1998.pdf(15页珍藏版)》请在三一文库上搜索。
1、o U O U O OD u) I u. lu 9 STD-EIA SBOAOAC-ENGL 1998 m 3234600 0595991 T25 m AN SI/ IA- 58 O A O AC-1998 Approv8d: May 15, 1998 EIA SPECIFICATION Detail Specification for Fixed Metallized Polyethylene Terephthalate Film Dielectric DC Capacitors Axial Leaded EIA-580AOAC JUNE 1998 ELECTRONIC INDUSTRIES
2、 ALLIANCE IZNGINEEXJNG DEPARTMENT Copyright Electronic Components, Assemblies ND = nondestructive. Inspection levels ( I L ) and acceptable quaiity levels (AQL) are selected from EC Publication 41O:Sampling plans and procedures for inspection by attributes Previous page is blank Copyright Electronic
3、 Components, Assemblies 1 ve cycles duration = 30 min visuai examination vlethod of mounting: See 1.1 of his specification rocedure B4 requency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or acceleration: 98 m/s2 (whichever is the less severe) Toial duration: 6 h Visual examination Method of mounting:
4、See 1.1 of this specification Acceleration: 490 m/s2 Duration of puise: 11 ms Puise shape: % sine wave Visual examination Capacitance Tangent of loss Insulation resistance Sample size performance C s 1 pF c 0.003; C 1 rU; Compared to values measured in 4.6.1. l Copyright Electronic Components, Assem
5、blies ND = nondestructive p = periodically (in months); n = sample size; c = acceptance criterion (permitted number of defective) Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Re
6、sale, 03/30/2007 02:41:29 MDTNo reproduction or networking permitted without license from IHS -,-,- STD.EIA SBOAOAC-ENGL 1998 3234b00 0596005 118 Standard or Generic Specification Standard Prefix for all Numbers Sectional Specification Designator Blank Detail Specification Designator Z L r IA STANDA
7、RD AND SPEClFlCATlON NUMBERING Detail Specification Designator . .- STANDARD - . A document that establishes engineering and technical requirements for processes, procedures, practices and methods that have been decreed by authority or adopted by consensus. Standards may also be established for sele
8、ction, application and design criteria for material. Standards and other documents not in the specification format use only the EIA basic numbering system as follows: IA-1 23 Original Standard EIA-I 23-1 Addendum to Original Standard EIA-123-A First Revision o f original Standard incorporating ali A
9、ddenda SPECIFICATION A document prepared specifically to facilitate procurement which clearly and accurately describes the essential technical requirements for purchased material. Procedures necessary to determine that the requirements for the purchased material covered by the specification have bee
10、n met shall also be referenced or included. EIA Specifjcations use the following system: IA 1230000 EIA 123AOOO EiA 123AAOO ElA 123AAAA EIA 123OOAA is a Generic Specification is a Sectional Specification is a Blank Detail Specification is a Detail Specification is a Detail Specification for which no
11、 Sectional or Blank Detail Specification was issued. NOTES: 1. Some older specifications may not have been converted to this numbering system. 2. See EP-l 1 “Guide for the Preparation of Specification Using IECQ-System Format,“ for more detail. Copyright Electronic Components, Assemblies & Materials Association Provided by IHS under license with ECA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/30/2007 02:41:29 MDTNo reproduction or networking permitted without license from IHS -,-,-