《ECA-EIA-ECA-364-13D-2007.pdf》由会员分享，可在线阅读，更多相关《ECA-EIA-ECA-364-13D-2007.pdf（12页珍藏版）》请在三一文库上搜索。
1、 ANSI/EIA-364-13D-2007 Approved: July 2, 2007 EIA STANDARD TP-13D MATING AND UNMATING FORCE TEST PROCEDURE FOR ELECTRICAL CONNECTORS AND SOCKETS EIA/ECA-364-13D (Revision of EIA-364-13C) EIA/ECA-364-13D JULY 2007 THE ELECTRONIC COMPONENTS SECTOR OF THE ELECTRONIC INDUSTRIES ALLIANCE NOTICE EIA Engin
2、eering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper pr
3、oduct for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude t
4、heir voluntary use by those other than EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, EIA does not assume any liab
5、ility to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is considered to have International Standardization implication, but the International Electrotechnical Commission activity has not progressed to the point where a
6、 valid comparison between the EIA Standard and the IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and heal
7、th practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5157 formulated under the cognizance of the CE-2.0 National Connector Standards Committee. Published by ELECTRONIC INDUSTRIES ALLIANCE 2007 Technology Strategy mating force, unmatin
8、g force, or both 5.3 Rates of mating and unmating, if other than specified in 4.1.1.2, 4.1.2, 4.2.1.2 and 4.2.2 5.4 Depth of mating if applicable 5.5 Lubrication or cleaning, if required 5.6 Wire type, gage, and length if applicable 5.7 Applicable hardware 5.8 Force or torque requirements 5.9 Test c
9、onditions, if other than standard atmospheric 5.10 Applicable to method B only: Details of the device(s) or gage(s) to be used for mating/unmating to the connector/socket, as well as the method and frequency of cleaning, if required -,-,- EIA-364-13D Page 4 6 Test documentation Documentation shall c
10、ontain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description including part number if applicable 6.3 If applicable, fixturing, gage details and gage part number 6.4 Test equipment used, and date of last and next calibration 6.5 Test pro
11、cedure and method, if other than method A 6.6 Values and observation 6.7 Name of operator and start/finish date(s) of test -,-,- EIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the
12、appropriate information below and mail or FAX to: Electronic Industries Alliance Technology Strategy & Standards Department Publications Office 2500 Wilson Blvd. Arlington, VA 22201 FAX: (703-875-8906) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of
13、 Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR EIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: -,-,- Revision H
14、istory Revision letter Project number Additions, changes and deletions C SP-5136 Original test procedure is now method A. Added Method B and paragraph 2.1.4, 3.2, 4.2, 5.10 and 6.3. Revised paragraph 1.1, 4.1.1.2, 4.1.2, 5.2, 5.3, 6.2 and 6.5. D 5157 Added paragraph 1.2, 2.2 and socket to title. Revised paragraph 2.1 4, 4.1 and 4.2. -,-,- -,-,-