《BS-6050-1981 ISO-4232-2-1980.pdf》由会员分享，可在线阅读，更多相关《BS-6050-1981 ISO-4232-2-1980.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 6050:1981 ISO 4232-2: 1980 Specification for Minimum information to be included in specification sheets of document copying machines ISO title: Office machines Minimum information to be included in specifications sheets Part 2: Document copying machines UDC 681.621.23.004.11 Lice
2、nsed Copy: sheffieldun sheffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 This British Standard, having been prepared under the direction of the Office Machines and Equipment Standards Committee, was published under the authority of the Executive Board and c
3、omes into effect on 31 March 1981 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference OMS/3 Draft for comment 78/65736 DC ISBN 0 580 11827 4 Cooperating organizations The Office Machines and Equipment Standards Committee, under whose direction this Briti
4、sh Standard was prepared, consists of representatives from the following: British Printing Industries Federation* Business Equipment Trade Association* Civil Service Department* Committee of London Clearing Bankers on behalf of the Committee of Scottish Clearing Bankers, Cooperative Bank, Central Tr
5、ustee Savings Bank and Yorkshire Bank* Drawing Office Material Manufacturers and Dealers Association Her Majestys Stationery Office* Institute of Administrative Management* Institute of Chartered Accountants in England and Wales Institute of Chartered Secretaries and Administrators* National Economi
6、c Development Office Office Machines and Equipment Federation* The organizations marked with an asterisk in the above list, together with the following, were directly represented on the Technical Committee entrusted with the preparation of this British Standard: Association of County Councils Britis
7、h Paper and Board Industry Federation (PIF) British Photographic Association British Railways Board Building Societies Association Greater London Council Library Association National Coal Board Post Office Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: sheffieldun s
8、heffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 BSI 12-1999i Contents Page Cooperating organizationsInside front cover National forewordii 0Introduction1 1Scope and field of application1 2Reference1 3Arrangement of the information1 4Information to be inclu
9、ded in specification sheets1 Table Minimum information to be included in specification sheets1 Publication referred toInside back cover Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 ii BSI 12-1999 National foreword This Britis
10、h Standard has been prepared under the direction of the Office Machines and Equipment Standards Committee and is identical with ISO 4232-2 “Office machines Minimum information to be included in specifications sheets Part 2: Document copying machines” published in 1980 by the International Organizati
11、on for Standardization (ISO). Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is espec
12、ially drawn to the following. Wherever the words “International Standard” appear, referring to this standard, they should be read as “British Standard”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their cor
13、rect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference International StandardCorresponding British Standard ISO 3066:1974BS 4588:1970 Methods of test for determining the registration obtained on duplicating machines (Technicall
14、y equivalent) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment tabl
15、e on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 BSI 12-19991 0 Introduction Document copying machines of many different types and capacities are now available and their specifications vary so widely
16、that it is often difficult for potential users to assess which machine(s) might best meet their requirements. 1 Scope and field of application This International Standard specifies the minimum information that shall be included in the specification sheets of document copying machines so that users m
17、ay compare directly the characteristics of different machines. It does not apply to microcopying equipment. 2 Reference ISO 3066, Duplicating machines Registration. 3 Arrangement of the information In order to comply with this International Standard, specification sheets shall contain, in the order
18、shown, all items listed in clause 4 below which are relevant to the machine being described. Additional points may be included under items 1 to 8, if appropriate. This information shall be given before any other data, and it is important that the numbers and headings for the main sections (for examp
19、le 2 Performance data) should be shown, although numbers identifying sub-sections such as 2.1 and 2.2 may be omitted. Where grammage (g/m2) data is given, it is assumed that the paper has been conditioned in the standard atmosphere defined in ISO 3066, i.e. at a temperature and relative humidity of
20、20 2 C and 65 5 % respectively. The minimum information given in 3.2.1 and 3.2.4 is for an original without the need for a supporting sheet. A note shall be included near the heading of the specification sheet to indicate that it has been drawn up in accordance with this International Standard. 4 In
21、formation to be included in specification sheets The following items comprise the minimum information that shall be included in the specification sheets of document copying machines: Table Minimum information to be included in specification sheets Numerical sequence Required informationIndication or
22、 value 1General data 1.1Machine name and model 1.2Type (state if fixed console, mobile console, table-top, etc.) 1.3Process employed (state if wet or dry) 2Performance data 2.1Initial warm-up time 2.2First copy out after warm-up time 2.3Average number of A4 copies per minute, from one original, excl
23、uding the first copy 3Requirements and characteristics of the machine 3.1Original passes into or through the machine (additional information may be given) yes/no 3.2Characteristics of original 3.2.1Size: minimum (if applicable) maximum 3.2.2Book form acceptableyes/no 3.2.3Type of original from which
24、 copies may be made: transparent translucent opaque yes/no yes/no yes/no Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 2 BSI 12-1999 Table Minimum information to be included in specification sheets Numerical sequence Required
25、informationIndication or value 3.2.4If 3.1 applies: thickness of original grammage of original minimum maximum minimum maximum 3.3Characteristics of copy paper (data being based on paper of 80 g/m2 where possible) 3.3.1Cut sheet: size grammage minimum maximum minimum maximum 3.3.2Roll: width length
26、cut to fixed length cut to manually-preselected length cut automatically to length of original minimum maximum minimum maximum 3.3.3Type of copy paper 3.3.3.1Specially treatedyes/no 3.3.3.2Describe any essential characteristics of the copy paper 3.3.3.3Transparencyyes/no 3.3.3.4Masters (state if off
27、set lithography, stencil duplicating, spirit duplicating, etc.) 3.4Reproduction scale 3.4.1Maximum image size at ratio 1 : 1 to original 3.4.2Deviation from 1 : 1 ratio to original 3.4.3Possible reductions 3.4.4Possible enlargements 3.5Copying on both sides of copy paperyes/no 3.5.1If 3.5 applies, c
28、opying is carried out: in same run by automatic re-cycling yes/no yes/no 3.6Preselection of number of copies required 3.6.1Maximum number preselectable 3.6.2Preselector returns to zero after each runyes/no 3.7Types of copy counter fitted: total with resetting facility yes/no yes/no Licensed Copy: sh
29、effieldun sheffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 BSI 12-19993 Table Minimum information to be included in specification sheets Numerical sequence Required informationIndication or value 3.8Nominal tray capacities (data being based on paper of 80
30、g/m2 where possible) feed tray receiving tray original tray 3.9Operator warning signals (list): 3.9.1For consumable supplies (for example copy paper low, toner low, etc.) 3.9.2For malfunctions (for example paper transport obstructed) 3.10Consumable supplies (list) 4Machine dimensions and mass (weigh
31、t) without consumable supplies and optional equipment: 4.1Length 4.2Width 4.3Height 4.4Mass (weight) 5Installation requirements (including those for air circulation, minimum floor space required for normal operation, and floor loading) Give details with dimensions or other quantitative data as appli
32、cable 6Electrical data 6.1Rated voltage(s) add DC (direct current), if applicable 6.2Rated frequency 6.3Rated input: maximum normal operating standby 6.4Fuse rating at connection point: single phase two phase three phase 6.5Connection to supply (state if plugged or permanent) 6.6Classification accor
33、ding to protection against electric shock Protection Class 1 (earth conductor required), or Protection Class 2 (no earth conductor required) 7Machine conforms to the following International Standards and regulations: 7.1Electrical safety 7.2Mechanical safety 7.3Other Licensed Copy: sheffieldun sheff
34、ieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 4 BSI 12-1999 Table Minimum information to be included in specification sheets Numerical sequence Required informationIndication or value 8Noise emission (state method of measurement or standard used) 8.1During s
35、tandby 8.2During normal operation 9Ancilliary equipment (list items suitable for use with the machines, including input/output devices) Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 BSI 12-1999 Publication referred to See nati
36、onal foreword. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6050:1981 ISO 4232-2: 1980 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British St
37、andards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the co
38、nstant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.
39、Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Cu
40、stomer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of info
41、rmation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020
42、8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists
43、in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any mea
44、ns electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other pu
45、rpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 10:17:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI