《IEC-61347-2-10-2009.pdf》由会员分享，可在线阅读，更多相关《IEC-61347-2-10-2009.pdf（46页珍藏版）》请在三一文库上搜索。
1、 IEC 61347-2-10 Edition 1.1 2009-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Lamp controlgear Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) Appareillages de lampes Partie 2-10: Prescriptio
2、ns particulires pour onduleurs et convertisseurs lectroniques destins lalimentation en haute frquence des lampes tubulaires dcharge dmarrage froid (tubes non) IEC 61347-2-10:2000+A1:2008 -,-,- THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved. Unless
3、 otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have an
4、y questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication
5、 ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous
6、dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International El
7、ectrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure
8、that you have the latest edition, a corrigenda or an amendment might have been published. ? Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projec
9、ts, withdrawn and replaced publications. ? IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. ? Electropedia: www.electropedia.org The worlds leading
10、online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. ? Customer Service Centre: www.iec.ch/webstore/custserv If
11、you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisati
12、on mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rce
13、nte, un corrigendum ou amendement peut avoir t publi. ? Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informati
14、ons sur les projets et les publications retires ou remplaces. ? Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. ? Electroped
15、ia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique Internation
16、al en ligne. ? Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 -,-,- I
17、EC 61347-2-10 Edition 1.1 2009-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Lamp controlgear Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) Appareillages de lampes Partie 2-10: Prescriptions
18、 particulires pour onduleurs et convertisseurs lectroniques destins lalimentation en haute frquence des lampes tubulaires dcharge dmarrage froid (tubes non) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE CE ICS 29.140.99 PRICE CODE CODE PRIX ISBN 2-8318-1024-5 R
19、egistered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 61347-2-10 IEC:2000+A1:2008 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Definitions 7 4 General requirements.8 5 General notes on tests .8
20、 6 Classification8 7 Marking 8 7.1 Items to be marked8 7.2 Durability and legibility of marking.8 8 Terminals .9 9 Provisions for earthing9 10 Protection against accidental contact with live parts .9 11 Moisture resistance and insulation10 12 Electric strength .10 13 Thermal endurance test for windi
21、ngs 10 14 Normal conditions.10 15 Abnormal conditions.11 16 Fault conditions11 17 Construction.12 18 Creepage distances and clearances .12 19 Protective circuits.12 20 Screws, current-carrying parts and connections14 21 Resistance to heat, fire and tracking.14 22 Resistance to corrosion 14 23 No-loa
22、d rated output voltage and rated output current 14 23.1 No-load rated output voltage .14 23.2 Rated output current14 23.3 Compliance .14 Annexes .15 61347-2-10 IEC:2000+A1:2008 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION LAMP CONTROLGEAR Part 2-10: Particular requirements for electronic invertors an
23、d convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IE
24、C is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS)
25、 and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with
26、 the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nea
27、rly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in tha
28、t sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committee
29、s undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking proce
30、dure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agen
31、ts including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of,
32、or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some o
33、f the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61347-2-10 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and re
34、lated equipment. This consolidated version of IEC 61347-2-10 consists of the first edition (2000) documents 34C/507/FDIS and 34C/521/RVD and its amendment 1 (2008) documents 34C/849/FDIS and 34C/859/RVD. The technical content is therefore identical to the base edition and its amendment and has been
35、prepared for user convenience. It bears the edition number 1.1. A vertical line in the margin shows where the base publication has been modified by amendment 1. -,-,- 4 61347-2-10 IEC:2000+A1:2008 This standard shall be used in conjunction with IEC 61347-1. It was established on the basis of the fir
36、st edition (2000) of that standard. This part 2 supplements or modifies the corresponding clauses in IEC 61347-1, so as to convert that publication into the IEC Standard: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamp
37、s (neon tubes) NOTE In this standard, the following print types are used: Requirements proper: in roman type. Test specifications: in italic type. NOTES: Explanatory matter: in smaller roman type. Annexes A, B, C, D, E, F, H and I form an integral part of this standard. IEC 61347 consists of the fol
38、lowing parts, under the general title: Lamp controlgear: Part 1: General and safety requirements Part 2-1: Particular requirements for starting devices (other than glow starters) Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps Part 2-3:
39、Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps Part 2-4: Particular requirements for d.c electronic ballasts for general lighting Part 2-5: Particular requirements for d.c. supplied electronic ballasts for public transport lighting Part 2-6: Particular requiremen
40、ts for d.c supplied electronic ballasts for aircraft lighting Part 2-7: Particular requirements for d.c supplied electronic ballasts for emergency lighting Part 2-8: Particular requirements for ballasts for fluorescent lamps Part 2-9: Particular requirements for ballasts for discharge lamps (excludi
41、ng fluorescent lamps) Part 2-10: Particular requirements for electronic invertors and convertors for high frequency operation of cold start tubular discharge lamps (neon tubes) Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires The committee has decided tha
42、t the contents of the base publication and its amendments will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a r
43、evised edition, or amended. 61347-2-10 IEC:2000+A1:2008 5 INTRODUCTION This part of IEC 61347, and the parts which make up IEC 61347-2, in referring to any of the clauses of IEC 61347-1, specify the extent to which such a clause is applicable and the order in which the tests are to be performed; the
44、y also include additional requirements, as necessary. All parts which make up IEC 61347-2 are self-contained and, therefore, do not include references to each other. Where the requirements of any of the clauses of IEC 61347-1 are referred to in this standard by the phrase ”The requirements of clause
45、 n of IEC 61347-1 apply”, this phrase is interpreted as meaning that all requirements of the clause in question of part 1 apply, except any which are clearly inapplicable to the specific type of lamp controlgear covered by this particular part of IEC 61347-2. -,-,- 6 61347-2-10 IEC:2000+A1:2008 LAMP
46、 CONTROLGEAR Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) 1 Scope This part of IEC 61347 specifies particular requirements for electronic invertors and convertors for high-frequency operatio
47、n of tubular cold-cathode discharge lamps used in signs and luminous discharge tube installations and operating with an output voltage exceeding 1 000 V but not exceeding 10 000 V for direct connection to supply voltages not exceeding 1 000 V at 50 Hz or 60 Hz or 1 000 V d.c. NOTE 1 In Japan, the ou
48、tput voltage of 15 000 V is acceptable. The requirements for two types of invertors and convertors, types A and B, are specified as follows: Type A unit: an invertor or convertor operating within the frequency range 20 kHz to 50 kHz, and having an output voltage (between terminals) not exceeding 5 000 V peak, a maximum output current limited to 35 mA (r.m.s.) and 50 mA (peak value). The supply voltage does not exceed 250 V at 50 Hz or 60 Hz or 250 V d.c. NOTE 2 The output current of a typ