《IEEE-C57.12.35-1996-R2004.pdf》由会员分享，可在线阅读，更多相关《IEEE-C57.12.35-1996-R2004.pdf（19页珍藏版）》请在三一文库上搜索。
1、The Institute of Electrical and Electronics Engineers, Inc. 345 East 47th Street, New York, NY 10017-2394, USA Copyright 1996 by the Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 1996. Printed in the United States of America. ISBN 1-55937-835-2 No part of thi
2、s publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. IEEE Std C57.12.35(R2004) IEEE Standard for Bar Coding for Distribution Transformers Sponsor Transformers Committee of the IEEE Power Engineering Societ
3、y Reaffirmed 24 June 2004 Approved 20 June 1996 IEEE-SA Standards Board Abstract: Bar code label requirements for overhead, pad-mounted, and underground-type distribution transformers are set forth in this standard. Included herein are requirements for data content, symbology, label layout, print qu
4、ality, and label life expectancy. Keywords: bar coding, distribution transformers Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=OConnor, Maurice Not for Resale, 04/28/2007 23:45:44 MDTNo reproducti
5、on or networking permitted without license from IHS -,-,- Introduction (This introduction is not part of IEEE Std C57.12.35-1996, IEEE Standard for Bar Coding for Distribution Transformers.) This standard describes requirements for bar code labels on distribution transformers when specified by users
6、. The intent of the bar code label described in this standard is to provide basic identification information for a transformer, as an aid in linking to more detailed information about the transformer that may reside in a utility companys central database. This standard describes requirements for a p
7、ermanent bar code label that may be part of the nameplate, as well as temporary bar code label, intended primarily for material management purposes. Requirements described in this standard address bar code label format, desired location of labels on specific type transformers, and performance requir
8、ements of the bar code labels. To the extent possible, industry standard bar code specifications and test methods are described. Use of this standard will promote standardization and uniformity in the use of bar code labels on distribution transformers. The Accredited Standards Committee on Transfor
9、mers, Regulators, and Reactors, C57, that reviewed and approved this document, had the following membership at the time of approval: P. E. Orehek, Chair vacant, Vice Chair John A. Gauthier, Secretary Electric Light and Power Group .E. A. Bertolini T. Diamantis K. Hanus M. C. Mingoia (Alt.) P. Orehek
10、 G. Paiva J. Sullivan Institute of Electrical and Electronics Engineers.W. B. Binder J. D. Borst J. H. Harlow J. W. Matthews L. Savio H. D. Smith (Alt.) G. H. Vaillancourt National Electrical Manufacturers Association G. D. Coulter P. Dewever (Alt.) J. Douglas S. Endersbe A. Ghafourian P. Hopkinson
11、K. R. Linsley R. L. Plaster (Alt.) H. Robin Tennessee Valley Authority.F. Lewis Underwriters Laboratories, Inc M. Schacker US Department of Agriculture, REA J. Bohlk US Department of Energy, Western Area Power Administration.Kenneth C. Wolohon US Department of Interior, Bureau of Reclamation R. Chad
12、wick US Department of the Navy, Civil Engineering Corps.H. P. Stickley Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=OConnor, Maurice Not for Resale, 04/28/2007 23:45:44 MDTNo reproduction or netwo
13、rking permitted without license from IHS -,-,- iii At the time it approved this standard, the IEEE/PES Transformers Committee had the following officers: J. H. Harlow, Chair W. B. Binder, Vice Chair J. W. Matthews, Secretary Georges Vaillancourt, Standards Coordinator At the time this standard was c
14、ompleted, the Working Group on Distribution Transformer Bar Code Labels had the following membership: Ron Jordan, Co-Chair Ed Smith, Co-Chair Anibal Alcintara, Jr. Glenn Anderson Jim Antweiler Jerry Bishop Alex Chan Tom Diamantis Kevin Edwards Dudley Galloway Ali Ghafourian John Gilbertson Ken Hanus
15、 Cass Hermerla J. Quinton Hodge Rick Hollingsworth John Hunt Kelley Knoerr John Lazar Timothy Lewis Jim Long Dave Lyon Al Maguire Angelynn McCain Matthew C. Mingoia Norvin Mohesky Gerry Paiva Clyde Pearson Thomas Pekarek Jack Phipps David Rolling John Rossetti Jerry Rowe Robert Scheu Jerry Smith Ron
16、ald J. Stahara Lou Tauber Al Traut Dorman Whitley Alan L. Wilks Other individuals who have contributed review and comment are the following: Claude Hertz Bert Moore Dan Mullen LaVerne Stetson Norm Weiland The following persons were on the balloting committee: Edward J. Adolphson D. J. Allan Raymond
17、Allustiarti Michael S. Altman Glenn Andersen J. C. Arnold J. Arteaga J. Aubin Donald E. Ayers Roy A. Bancroft Ron L. Barker David A. Barnard E. A. Bertolini Wallace B. Binder J. H. Bishop W. E. Boettger J. V. Bonucchi John D. Borst C. V. Brown M. Cambre D. J. Cash D. Chu Thomas F. Clark J. L. Corkra
18、n Dan W. Crofts John C. Crouse V. Dahinden John N. Davis R. C. Degeneff T. Diamantis Larry E. Dix R. F. Dudley John A. Ebert K. Edwards Fred E. Elliott D. J. Fallon P. T. Feghali Jeffrey A. Fleeman Michael A. Franchek Jerry M. Frank Dudley L. Galloway A. A. Ghafourian Donald A. Gillies R. S. Girgis
19、R. D. Graham Robert L. Grubb R. L. Grunert F. J. Gryszkiewicz Michael E. Haas Geoff H. Hall E. Hanique N. Wayne Hansen Kenneth S. Hanus James H. Harlow Frank W. Heinrichs William R. Henning K. R. Highton Peter J. Hoefler Philip J. Hopkinson J. W. Howard Copyright The Institute of Electrical and Elec
20、tronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=OConnor, Maurice Not for Resale, 04/28/2007 23:45:44 MDTNo reproduction or networking permitted without license from IHS -,-,- iv Edgar Howells J. Hunt Y. Peter Iijima C. W. Johnson Anthony J. Jonn
21、atti R. D. Jordan E. Kallaur J. J. Kelly William N. Kennedy James P. Kinney Sheldon P. Kennedy Alexander D. Kline J. G. Lackey Michael Y. Lau J. P. Lazar Frank A. Lewis Harold F. Light S. R. Lindgren Larry A. Lowdermilk Richard I. Lowe Donald L. Lowe Joseph Ma William A. Maguire K. T. Massouda John
22、W. Matthews A. D. McCain Jack W. McGill Charles J. McMillen W. J. McNutt Charles P. McShane Ross McTaggart Sam P. Mehta C. Kent Miller Matthew C. Mingoia Russell E. Minkwitz Michael I. Mitelman Harold R. Moore W. E. Morehart D. H. Mulkey C. R. Murray R. J. Musil William H. Mutschler Carl G. Niemann
23、E. T. Norton Paul E. Orehek Gerald A. Paiva Klaus Papp Bipin K. Patel Wesley F. Patterson, Jr. J. M. Patton Paulette A. Payne Larry C. Pearson Thomas J. Pekarek Dan D. Perco Mark D. Perkins V. Q. Pham Linden W. Pierce R. L. Plaster Donald W. Platts Bertrand Poulin Jeewan L. Puri Vadim Raff J. D. Ram
24、boz Charles T. Raymond Pierre Riffon Peter G. Risse S. M. A. Rizvi Chris A. Robbins R. B. Robertson A. L. Robinson J. R. Rossetti G. W. Rowe Mahesh P. Sampat Leo J. Savio William E. Saxon Robert W. Scheu Devki N. Sharma V. Shenoy Hyeong J. Sim Stephen D. Smith James E. Smith J. Ed Smith J. W. Smith
25、Ronald J. Stahara W. W. Stein Ron W. Stoner John C. Sullivan David Sundin Louis A. Tauber James B. Templeton V. Thenappan James A. Thompson R. W. Thompson Thomas P. Traub E. R. Trummer Georges H. Vaillancourt Robert A. Veitch Loren B. Wagenaar Barry H. Ward R. J. Whearty D. W. Whitley A. L. Wilks Ch
26、arles W. Williams When the IEEE Standards Board approved this standard on 20 June 1996, it had the following membership: Donald C. Loughry, Chair Richard J. Holleman, Vice Chair Andrew G. Salem, Secretary Gilles A. Baril Clyde R. Camp Joseph A. Cannatelli Stephen L. Diamond Harold E. Epstein Donald
27、C. Fleckenstein Jay Forster * Donald N. Heirman Ben C. Johnson E. G. “Al” Kiener Joseph L. Koepfinger * Stephen R. Lambert Lawrence V. McCall L. Bruce McClung Marco W. Migliaro Mary Lou Padgett John W. Pope Jose R. Ramos Arthur K. Reilly Ronald H. Reimer Gary S. Robinson Ingo Rsch John S. Ryan Chee
28、Kiow Tan Leonard L. Tripp Howard L. Wolfman * Member Emeritus Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=OConnor, Maurice Not for Resale, 04/28/2007 23:45:44 MDTNo reproduction or networking per
29、mitted without license from IHS -,-,- v Also included are the following nonvoting IEEE Standards Board liaisons: Satish K. AggarwalAlan H. CooksonChester C. Taylor Rochelle L. Stern IEEE Standards Project Editor Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS un
30、der license with IEEELicensee=IHS Employees/1111111001, User=OConnor, Maurice Not for Resale, 04/28/2007 23:45:44 MDTNo reproduction or networking permitted without license from IHS -,-,- vi CLAUSEPAGE 1. Overview.1 1.1 Scope 1 1.2 Purpose. 1 2. References.1 3. Definitions.2 4. Bar code label requir
31、ements3 4.1 Permanent bar code label. 3 4.2 Temporary bar code label 5 Annex A (Informative) Manufacturer/repair facility identification codes12 Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001, User=OConno
32、r, Maurice Not for Resale, 04/28/2007 23:45:44 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright 1996 IEEE All Rights Reserved1 IEEE Standard for Bar Coding for Distribution Transformers 1. Overview 1.1 Scope This standard sets forth bar code label requirements for
33、overhead, padmounted, and underground-type distribution transformers. Included herein are requirements for data content, symbology, label layout, print quality, and label life expectancy. This standard assumes the existence of central transformer databases within utility companies so that bar code l
34、abels need only carry basic transformer identification data. 1.2 Purpose The purpose of this standard is to promote standardization and uniform use of bar code labels on distribution transformers when specified by the user. Longer term, it is hoped that the bar codes provided as a result of this sta
35、ndard will serve as an integral part of electrical utility material and information management systems. 2. References When the following standards are superseded by an approved revision, the revision shall apply: AIM Uniform Symbology Specification USS-39-1986.1 ANSI X3.182-1990. Bar Code Print Qual
36、ityGuidelines.2 ANSI C57.12.20-1994 (R1995), Requirements for Overhead-Type Distribution Transformers, 500 kVA and Smaller: High Voltage, 34 500 Volts and Below; Low Voltage, 7970/13 800 Y Volts and Below. 1AIM publications are available from the Automatic Identification Manufacturers at (412) 963-8
37、588. 2ANSI publications are available from the Sales Department, American National Standards Institute, 11 West 42nd Street, 13th Floor, New York, NY 10036, USA. Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/111111
38、1001, User=OConnor, Maurice Not for Resale, 04/28/2007 23:45:44 MDTNo reproduction or networking permitted without license from IHS -,-,- 2Copyright 1996 IEEE All Rights Reserved IEEE Std C57.12.35-1996IEEE STANDARD FOR BAR CODING ANSI C57.12.21-1995, Requirements for Pad-Mounted, Compartmental-Type
39、, Self-Cooled, Single-Phase Distribution Transformers with High-Voltage, 34 500 GrdY/19 920 Volts and Below; Low-Voltage, 240/120 Volts; 167 kVA and Smaller. ANSI C57.12.22-1989, Requirements for Pad-Mounted, Compartmental-Type, Self-Cooled, Three-Phase Distribution Transformers with High-Voltage Bu
40、shings, 2500 kVA and Smaller, High-Voltage, 34 500 GrdY/19 920 Volts and Below; Low Voltage, 480 Volts and Below. ANSI C57.12.23-1992, Standard for TransformersUnderground-Type, Self-Cooled, Single-Phase Distribution Transformers with Separable Insulated High-Voltage ConnectorsHigh-Voltage, 24 940 G
41、rdY/14 400 V and Below; Low-Voltage, 240/120 V; 167 kVA and Smaller. ANSI C57.12.24-1994, Requirements for Underground-Type Three-Phase Distribution Transformers, 2500 kVA and Smaller: High-Voltage, 34 500 GrdY/19 920 Volts and Below; Low-Voltage, 480 Volts and Below. ANSI C57.12.25-1990, Requiremen
42、ts for Pad-Mounted, Compartmental-Type, Self-Cooled, Single-Phase Distribution Transformers with Separable Insulated High-Voltage Connectors: High-Voltage, 34 500 GrdY/19 920 Volts and Below; Low-Voltage, 240/120 Volts; 167 kVA and Smaller. ANSI C57.12.26-1993, Standard for Transformers-Pad Mounted,
43、 Compartmental-Type, Self-Cooled, Three-Phase Distribution Transformers for Use with Separable Insulated High-Voltage Connectors, High-Voltage, 34 500 GrdY/19 920 Volts and Below; 2500 kVA and Smaller. ANSI C57.12.40-1990, Requirements for Secondary Network Transformers, Subway and Vault Types. ASTM
44、 B117-95, Standard Method of Salt Spray (Fog) Apparatus.3 ASTM G53-95, Standard Recommended Practice for Operating Light- and Water-Exposure Apparatus for Exposure of Nonmetallic Materials. IEEE Std C57.12.00-1993, IEEE Standard General Requirements for Liquid-Immersed Distribution, Power, and Regul
45、ating Transformers (ANSI).4 3. Definitions 3.1 ASCII: The code described in ANSI X3.4-1986, using a coded character set consisting of 7-bit coded characters (8 bits, including parity check), used for information interchange among data processing systems, communications systems, and associated equipm
46、ent. The ASCII set consists of control characters and graphic characters. 3.2 bar: The darker element of a bar code. 3.3 bar code: An array of rectangular marks and spaces in a predetermined pattern. 3.4 bar code symbol: An array of rectangular bars and spaces that are arranged in a predetermined pa
47、ttern following specific rules to represent elements of data that are referred to as characters. A bar code symbol typically contains a leading quiet zone, start character, data character(s) including a check character (if any), stop character, and a trailing quiet zone. 3.5 bidirectional bar code s
48、ymbol: A bar code symbol format that permits decoding of the contents whether scanned in one direction or the reverse direction. 3ASTM publications are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428- 2959, USA. 4IEEE publications are available from the Institute of Electrical and Electronics Engineers, 445 Hoes Lane, P.O. Box 1331, Piscataway, NJ 08855- 1331, USA. Copyright The Institute of Electrical and Electronics Engineers, Inc. Provided by IHS under license with IEEELicensee=IHS Employees/1111111001,