《BS-EN-2832-1993.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2832-1993.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2832:1993 Hydrogen embrittlement of steels Notched specimen test The European Standard EN 2832:1993 has the status of a British Standard UDC 669.14:621:793/794:620.172:629.7 BS EN 2832:1993 This British Standard, having been prepared under the direction of the
2、 Aerospace Standards Policy Committee (ACE/-), was published under the authority of the Standards Board and comes into effect on 15 May 1993 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/44 Draft for comment 90/75755 DC ISBN 0 580 22148 2 Coope
3、rating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following (CEN) countries: AustriaOesterreichisches Normungsinstitut BelgiumInstitut belge de normalisation Denmar
4、kDansk Standardiseringsraad FinlandSuomen Standardisoimisliito, r.y. FranceAssociation franaise de normalisation GermanyDeutsches Institut fr Normung e.V. GreeceHellenic Organization for Standardization IcelandTechnological Institute of Iceland IrelandNational Standards Authority of Ireland ItalyEnt
5、e Nazionale Italiano di Unificazione LuxembourgInspection du Travail et des Mines NetherlandsNederlands Normalisatie-instituut NorwayNorges Standardiseringsforbund PortugalInstituto Portugus da Qualidade SpainAsociacin Espaola de Normalizacin y Certificacin SwedenStandardiseringskommissionen i Sveri
6、ge SwitzerlandAssociation suisse de normalisation United KingdomBritish Standards Institution Amendments issued since publication Amd. No.DateComments BS EN 2832:1993 BSI 12-1999i Contents Page Cooperating organizationsInside front cover National forewordii Foreword2 Text of EN 28323 National annex
7、NA (informative) Committees responsibleInside back cover BS EN 2832:1993 ii BSI 12-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN 2832:1993, Aerospace series Hydrogen embrittleme
8、nt of steels Notched specimen test published by the European Committee for Standardization (CEN). EN 2832 was produced as a result of international discussion in which the United Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. U
9、sers of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an in
10、side back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2832 February 1993 UDC 669.14:621.793/794:620.
11、172:629.7 Descriptors: Aircraft industry, steels, hydrogen embrittlement, tests, test specimens English version Aerospace series Hydrogen embrittlement of steels Notched specimen test Srie arospatiale Fragilisation des aciers par lhydrogne Essai par prouvette entaille Luft- und Raumfahrt Wasserstoff
12、versprdung von Sthlen Kerbzugversuch This European Standard was approved by CEN on 1993-02-19. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-da
13、te lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the
14、 responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Nether
15、lands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1993 Copyright reserved to CEN members Ref. No. EN 2832:1993 E EN
16、2832:1993 BSI 12-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Assoc
17、iations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 1993, and conflicting national standard
18、s shall be withdrawn at the latest by August 1993. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal
19、, Spain, Sweden, Switzerland and United Kingdom. Contents Page Foreword2 1Scope3 2Apparatus3 3Test specimens3 4Procedure3 5Fault sanction3 6Test report3 Figure 14 Table 14 EN 2832:1993 BSI 12-19993 1 Scope This standard specifies the method for the notched specimen test, which is used to assess the
20、hydrogen embrittlement of steels during chemical or electrolytic surface treatments. It is applicable whenever referenced. 2 Apparatus Any device allowing a constant load to be applied to the test specimens may be used, i.e. direct load machines, dynamometric rings, etc. 3 Test specimens 3.1 Materia
21、l and heat treatment They shall be identical with those of the parts. However, the purchaser may require to use a reference material and heat treatment. 3.2 Dimensions See Figure 1 and Table 1. 3.3 Surface treatment It shall be carried out as on the parts and ensure that the thickness of the deposit
22、 at the notch root is the same as that specified for the parts. 3.4 De-embrittlement It shall be carried out as for the parts. 4 Procedure The test specimens shall be subjected for 200 h, at ambient temperature, to an axial load equal to (75 2) % of the tensile strength of a notched uncoated specime
23、n. 5 Fault sanction No fracture is permissible before 200 h. 6 Test report It shall include the following: reference to this standard; reference numbers and types of the test specimens; nature of the coating; thickness of the coating; test result. EN 2832:1993 4 BSI 12-1999 Table 1 Figure 1 Dimensio
24、ns en millimetres Type DEGR1R2 nom.tol.nom.tol.nom.tol.min.max.nom.tol. 16,40 0,03 9,07 0,08 14+ 1 0 3,186,350,23 0,013 24,526,3517,5+ 1 0 0,13 BS EN 2832:1993 BSI 12-1999 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Stan
25、dard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/44 upon which the following bodies were represented: Aluminium Finishing Association Metal Finishing Association Ministry of Defence National Centre of Tribology Oil and Colour Chemists Association Pain
26、tmakers Association of Great Britain Ltd. Society of British Aerospace Companies Limited BS EN 2832:1993 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards i
27、n Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our
28、 products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI off
29、ers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8
30、996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international
31、 standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept
32、up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the cop
33、yright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or other
34、wise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.