《BS-4F-58-1990.pdf》由会员分享，可在线阅读，更多相关《BS-4F-58-1990.pdf（8页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS 4F 58:1990 Superseding BS 3F 58:1975 Specification for Cotton thread for aerospace purposes Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 07:36:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 4F 58:1990 This British Standard, having been prepared under
2、the direction of the Aerospace Standards Policy Committee (ACE/-), was published under the authority of the Board of BSI and comes into effect on 31 August 1990 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference ACE/22 Draft for comment 88/75255 DC ISBN
3、 0 580 17910 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/22, upon which the following bodies were represented: British Association of Clothing Machinery Manufa
4、cturers British Narrow Fabrics Association Cordage Manufacturers Institute Lambeg Industrial Research Association Linen Sewing Thread Manufacturers Association Man-made Fibres Producers Committee Ministry of Defence Society of British Aerospace Companies Limited Society of Dyers and Colourists Amend
5、ments issued since publication Amd. No.Date of issueComments Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 07:36:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 4F 58:1990 BSI 02-2000i Contents Page Committees responsibleInside front cover Forewordii 1Scope1 2General requirements1 3Yarn1 4
6、Construction and properties1 5Finish1 6Type test1 7Identification1 Table 1 General requirements1 Table 2 Construction and properties of finished thread2 Publications referred toInside back cover Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 07:36:34 GMT+00:00 2006, Uncontrolled Copy, (c) BS
7、I BS 4F 58:1990 ii BSI 02-2000 Foreword This British Standard prepared under the direction of the Aerospace Standards Policy Committee is one of a series for materials of a quality suitable for aerospace purposes. It is a revision of BS 3F 58 which is withdrawn. It differs from the previous edition
8、primarily in that only one thread is now specified. The quality assurance authority referred to in this standard is as stated in the contract or order, or the accredited representative of the authority stated, as instructed by the prime contractors. A British Standard does not purport to include all
9、 the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and
10、ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 07:36:34 GMT+00:00 2
11、006, Uncontrolled Copy, (c) BSI BS 4F 58:1990 BSI 02-20001 1 Scope This British Standard specifies the requirements for a cotton thread, for use primarily as safety ties and break threads, for aerospace purposes. NOTE 1The titles of publications referred to in this standard are listed on the inside
12、back cover. NOTE 2The latest revision of an Aerospace standard is indicated by the prefix number. 2 General requirements 2.1 In addition to the requirements specified in clauses 3 to 7 of this standard the requirements of the latest edition of BS F 100 indicated in Table 1 shall apply. 2.2 Thread ma
13、nufactured in accordance with this standard shall comply with the following. a) Freedom from defects. i) The thread shall have uniformity of thickness, construction, and component ply tension so that there are no visually irregular twist defects. ii) The thread shall contain no thread knots. NOTEUp
14、to two laid-on ends per package are permitted. b) Length per unit mass. The length per unit mass of thread shall be determined in accordance with BS 2010, method A. 3 Yarn The thread shall be manufactured from combed cotton yarn. 4 Construction and properties 4.1 The construction and properties of t
15、he finished thread shall comply with the requirements of Table 2. 4.2 The direction of final twist shall be Z. 5 Finish 5.1 Condition of material The thread shall be supplied scoured, dyed to BS 381C shade 539 and rot-proofed with pentachlorophenyl laurate (PCPL) in accordance with BS 2087-1, normal
16、 process. NOTEIt is very important that the scouring process is thorough in order to remove surface acting agents, and processing acids. 5.2 Finish 5.2.1 The thread shall have a soft finish. 5.2.2 Finishes which promote microbiological growth (e.g. starch or modified starch) shall not be applied. NO
17、TEA lubricating finish may be applied to the thread to facilitate its performance. 6 Type test 6.1 General 6.1.1 The type test specified in 6.2 shall be carried out to the satisfaction of the quality assurance authority. 6.1.2 After initial satisfaction of the type test, no changes in respect of eit
18、her the materials or processing conditions used shall be made without the type test being repeated to the satisfaction of the quality assurance authority. 6.1.3 The manufacturers records of type tests shall be made available to the quality assurance authority on request. 6.2 Loop breaking strength T
19、he thread shall have a minimum average loop breaking strength of 20 N when tested in accordance with BS 1932-2. 7 Identification The thread shall be identified for ordering purposes by the number of this British Standard, i.e. BS 4F 58. Table 1 General requirements (given in BS F 100) SectionTitleRe
20、quirements and tests 1GeneralAll requirements. 2aQuality requirementsRequirements for dyed textiles except those relating to fabric intended for coating. Requirements for freedom from corrosive impurities (see section 4). 3Physical testsTests for breaking strength and extension under load. 4Chemical
21、 testsIf required by Section 2, test for freedom from corrosive impurities. a It is not intended that section 2 tests should be performed on each thread batch. The frequency of these tests should be agreed between the quality assurance authority and the thread manufacturer. Licensed Copy: sheffieldu
22、n sheffieldun, na, Fri Dec 01 07:36:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 4F 58:1990 2 BSI 02-2000 Table 2 Construction and properties of finished thread Designation Structure Nominal tex/turns per metrea (tpm) Minimum length per unit mass Minimum average breaking strength Maximum strengt
23、h 60/2/310 tex 2S 1 350-1 650 3Z 530-650 m/kg 14 500b N 13.3 N 20 a The twist shall be determined in accordance with BS 2085. b The added mass due to the dye and finish should not exceed a total of 10 % of the original mass. Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 07:36:34 GMT+00:00 2
24、006, Uncontrolled Copy, (c) BSI BS 4F 58:1990 BSI 02-2000 Publications referred to BS F 100, Procedure for inspection and testing of textiles for aerospace purposes. BS 381C, Specification for colours for identification, coding and special purposes. BS 1932, Methods of testing the strength of yarns
25、and threads from packages. BS 1932-2, Determination of knot strength and loop strength. BS 2010, Method for determination of the linear density of yarns from packages. BS 2085, Method of test for determination of twist in yarns, direct counting method. BS 2087, Preservative treatments for textiles.
26、BS 2087-1, Specification for treatments. Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 07:36:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 4F 58:1990 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing
27、British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It
28、 is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside fro
29、nt cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addre
30、ssed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide ran
31、ge of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111.
32、 Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright
33、 subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or
34、by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for an
35、y other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 07:36:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSI