《BS-EN-3545-009-2008.pdf》由会员分享，可在线阅读，更多相关《BS-EN-3545-009-2008.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 3545-009:2008 Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures p p55 C to 175 C Part 009: Protective cover for plug and receptacle Product standard ICS 49.060 ? Licensed CopyChinese U
2、niversity of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI BS EN 3545-009:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 August 2008 BSI 2008 ISBN 978 0 580 60576 5 National foreword This British Standard is the UK implemen
3、tation of EN 3545-009:2008. The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purpor
4、t to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments Licensed CopyChinese University of Hong Kong, 21/1
5、0/2008 07:50, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3545-009 June 2008 ICS 49.060 English Version Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 C to 175 C
6、 - Part 009: Protective cover for plug and receptacle - Product standard Srie arospatiale - Connecteurs lectriques, rectangulaires, tanches et non tanches larrire, botier en plastique, verrouillage, tempratures dutilisation - 55 C 175 C - Partie 009 : Capot de protection pour fiche et embase - Norme
7、 de produit Luft- und Raumfahrt - Elektrische Rechtecksteckverbinder mit und ohne hintere Abdichtung, Plastikgehuse, Verriegelungssystem, Betriebstemperaturen von - 55 C bis 175 C - Teil 009: Schutzkappe fr festen und freien Steckverbinder - Produktnorm This European Standard was approved by CEN on
8、14 March 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may b
9、e obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN
10、Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands
11、, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in a
12、ny form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3545-009:2008: E Licensed CopyChinese University of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitions .4 4 Required characterist
13、ics.4 5 Designation 6 6 Marking.7 7 Technical specification .7 BS EN 3545-009:2008 Licensed CopyChinese University of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI 3 Foreword This document (EN 3545-009:2008) has been prepared by the Aerospace and Defence Industries Association of Europe -
14、Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard
15、shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2008, and conflicting national standards shall be withdrawn at the latest by December 2008. Attention is drawn to the possibility that some of the elements of thi
16、s document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Stan
17、dard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
18、 BS EN 3545-009:2008 Licensed CopyChinese University of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI 4 1 Scope This standard specifies the characteristics of protective cover for plug and receptacle in the family of rectangular electrical connectors with sealed and non-sealed rear, plasti
19、c housing, locking device, for operating temperatures from 55 C to 175 C. The protective covers are not able to ensure a sealing in immersion condition. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the ed
20、ition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3545-001, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Par
21、t 001: Technical specification. EN 3545-002, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 002: Specification of performance and contact arrangements. EN 3545-005, Aerospace series Con
22、nectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 005: Female coding and attachment system for mounting on free housing (plug) Product standard. EN 3545-006, Aerospace series Connectors, electrical, rectangul
23、ar, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 006 : Male coding and attachment system for mounting on fixed housing (receptacle) Product standard. 3 Terms and definitions For the purposes of this document, the terms and definitions gi
24、ven in EN 3545-001 apply. 4 Required characteristics 4.1 Dimensions and mass See Figure 1. Dimensions and tolerances are in millimetres. Mass: with attachments: 19 g max.; without attachment: 9 g max. The female attachment system corresponds to EN 3545-005 without the locating coding device (half mo
25、on), see Figure 2. The male attachment system corresponds to EN 3545-006 without the locating coding device (half moon), see Figure 3. BS EN 3545-009:2008 Licensed CopyChinese University of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI 5 Key 1 Part number 5 Optional chain or cable (length
26、(80 5) mm) 2 Molding batch 6 Attachment system for mounting on free housing 3 Codable for mounting connector with pins 7 Seal 4 Attachment system for mounting on fixed housing 8 Codable for mounting connector with sockets Figure 1 Figure 2 Female attachment system Figure 3 Male attachment system 1 2
27、 3 5 7 4 7 6 8 Socket interface Pin interface BS EN 3545-009:2008 Licensed CopyChinese University of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI 6 4.2 Recommended panel cut-out for fixed housing (receptacle) fitted with male attachment system See Figure 4. Maximum thickness of panel: 1,6
28、 Minimum pitch between connectors: 14,2 Figure 4 4.3 Main general characteristics See EN 3545-002. 5 Designation EXAMPLE Description block COVER, ELECTRICAL CONNECTOR Identity block EN3545-009CPC Number of the basic standard C: Protective cover Type of protective cover P: Plug (free housing) deliver
29、ed with female attachment system (to cover a receptacle), R: Receptacle (fixed housing) delivered with male attachment system. BS EN 3545-009:2008 Licensed CopyChinese University of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI 7 Type of termination C: With chain or cable, Without code: wi
30、thout chain or cable. 6 Marking 6.1 General Unless there are other specific contracted requirements, the marking shall include. 6.2 Marking on the product the manufacturers part number of the housing alone (without the attachment system and without the chain); the date of manufacture (year, week); t
31、he manufacturers name or trade mark. 6.3 Marking on the individual packaging the EN reference corresponding to the purchasing order (housing with male or female attachment system and with/without chain); the manufacturers part number corresponding to the above EN reference; the date of manufacture (
32、year, week); the manufacturers name or trademark. 7 Technical specification See EN 3545-001. BS EN 3545-009:2008 Licensed CopyChinese University of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI BS EN 3545-009:2008 BSI Group Headquarters 389 Chiswick High Road, London W4 4AL, UK Tel +44 (0)
33、20 8996 9001 Fax +44 (0)20 8996 7001 British Standards Institution (BSI) BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards
34、are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this
35、 British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400 BSI offers members an individual updating service called PLUS which ensures that subscribers automatica
36、lly receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Sho
37、p on the Website http:/ In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and
38、 international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subs
39、cribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding onli
40、ne access to British Standards via British Standards Online can be found at http:/ Further information about BSI is available on the BSI website at http:/. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standard
41、ization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclu
42、de the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: Licensed CopyChinese University of Hong Kong, 21/10/2008 07:50, Uncontrolled Copy, (c) BSI