《IEC-61076-2-104-2008.pdf》由会员分享，可在线阅读，更多相关《IEC-61076-2-104-2008.pdf（74页珍藏版）》请在三一文库上搜索。
1、 IEC 61076-2-104 Edition 1.0 2008-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment Product requirements Part 2-104: Circular connectors Detail specification for circular connectors with M8 screw-locking or snap-locking Connecteurs pour quipements lectroniques Exigen
2、ces de produit Partie 2-104: Connecteurs circulaires Spcification particulire pour les connecteurs circulaires M8 vis ou encliquetage IEC 61076-2-104:2008 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/200
3、8 04:58:04 MDTNo reproduction or networking permitted without license from IHS -,-,- THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
4、 electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, pl
5、ease contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcaniqu
6、e, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez
7、 le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International
8、 Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. ? Catalogue of IEC
9、 publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. ? IEC Just Published: www.iec.ch/online_news/justpub Stay up to dat
10、e on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. ? Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in En
11、glish and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. ? Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer
12、Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectroniqu
13、e et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. ? Catalogue des publications de la CEI: www.iec.ch/sea
14、rchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. ? Just Published CEI: www.iec.ch/online_news/j
15、ustpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. ? Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il
16、contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. ? Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner
17、 des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/591077
18、0001 Not for Resale, 07/25/2008 04:58:04 MDTNo reproduction or networking permitted without license from IHS -,-,- IEC 61076-2-104 Edition 1.0 2008-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment Product requirements Part 2-104: Circular connectors Detail specifica
19、tion for circular connectors with M8 screw-locking or snap-locking Connecteurs pour quipements lectroniques Exigences de produit Partie 2-104: Connecteurs circulaires Spcification particulire pour les connecteurs circulaires M8 vis ou encliquetage INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION
20、 ELECTROTECHNIQUE INTERNATIONALE V ICS 31.220.10 PRICE CODE CODE PRIX ISBN 2-8318-9670-3 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 04:58:04 MDTNo reproduction or networking permitted without lice
21、nse from IHS -,-,- 2 61076-2-104 IEC:2008 CONTENTS FOREWORD.5 1 General information8 1.1 Scope8 1.2 Recommended method of termination .8 1.2.1 Number of contacts or contact cavities 8 1.3 Ratings and characteristics .8 1.4 Normative references 8 1.5 Marking .9 1.6 IEC Type designation 10 1.7 Orderin
22、g information10 1.8 Safety aspects.11 2 Technical information .11 2.1 Terms and definitions11 2.2 Survey of styles and variants.11 2.2.1 General .11 2.2.2 Fixed connectors .11 2.2.3 Free connectors 13 3 Dimensions 18 3.1 General.18 3.2 Interface dimensions .19 3.2.1 Pin front view A-coding19 3.2.2 P
23、in front view B-Coding .20 3.3 Engagement (mating) information21 3.4 Gauges .23 4 Characteristics .23 4.1 Climatic category.23 4.2 Electrical .23 4.2.1 Rated voltage Rated impulse voltage Pollution degree.23 4.2.2 Voltage proof.24 4.2.3 Current-carrying capacity.24 4.2.4 Contact resistance.24 4.2.5
24、Insulation resistance24 4.3 Mechanical24 4.3.1 IP degree of protection 24 4.3.2 Mechanical operation 25 4.3.3 Insertion and withdrawal forces .25 4.3.4 Contact retention in insert25 4.3.5 Polarizing method25 4.3.6 Vibration (sinusoidal).25 5 Test schedule.26 5.1 General.26 5.1.1 Arrangement for cont
25、act resistance measurements26 5.1.2 Arrangement for dynamic stress tests (vibration) .28 5.2 Test schedule29 5.2.1 Test group P Preliminary 29 5.2.2 Test group AP Dynamic/ Climatic29 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/59107700
26、01 Not for Resale, 07/25/2008 04:58:04 MDTNo reproduction or networking permitted without license from IHS -,-,- 61076-2-104 IEC:2008 3 5.2.3 Test group BP Mechanical endurance.32 5.2.4 Test group CP Electrical load .33 5.2.5 Test group DP Chemical resistivity .34 5.2.6 Test group EP Connection meth
27、od tests .34 Annex A (informative) Diameter of the female connector body .35 Figure 1 Tube insert, male contacts dip solder, mounting long version.11 Figure 2 Tube insert, male contacts dip solder, mounting short version12 Figure 3 Fixed connector with wire ends, male contacts, single hole mounting.
28、12 Figure 4 Fixed connector with wire ends, female contacts, single hole mounting13 Figure 5 Rewireable connector, male contacts, straight version, with locking nut .14 Figure 6 Rewireable connector, male contacts, right angled version, with locking nut 14 Figure 7 Non-rewireable connector, male con
29、tacts, straight version, snap locking15 Figure 8 Non-rewireable connector, male contacts, straight version, with locking nut.15 Figure 9 Non-rewireable connector, male contacts, angled version, with locking nut 15 Figure 10 Rewireable connector, female contacts, straight version, with locking nut 16
30、 Figure 11 Rewireable connector, female contacts, right angled version, with locking nut16 Figure 12 Non-rewireable connector, female contacts, straight version, snap locking.16 Figure 13 Non-rewireable connector, female contacts, angled version, snap locking17 Figure 14 Non-rewireable connector, fe
31、male contacts, straight version, with locking nut 17 Figure 15 Non-rewireable connector, female contacts, angled version with locking nut 17 Figure 16 Pin front view A-coding 19 Figure 17 Contact position A-Coding front view20 Figure 18 Pin front view B-Coding20 Figure 19 Contact position B-Coding -
32、 front view.20 Figure 20 Engagement (mating) information.21 Figure 21 Gauge dimensions .23 Figure 22 Contact resistance arrangement.27 Figure 23 Dynamic stress test arrangement .28 Figure A.1 Diameter of the female connector body, coding variant A35 Figure A.2 Shape of the female connector body, cod
33、ing variant B35 Table 1 Styles of fixed connectors .11 Table 2 Styles of free connectors.13 Table 3 Connectors dimensions in mated and locked position22 Table 4 Gauges .23 Table 5 Climatic category 23 Table 6 Rated voltage Rated impulse voltage Pollution degree 24 Table 7 Voltage proof.24 Table 8 Nu
34、mber of mechanical operations .25 Table 9 Insertion and withdrawal forces .25 Table 10 Number of test specimens .26 Table 11 Test group P .29 Table 12 Test group AP .29 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=Boeing Co/5910770001 Not for Res
35、ale, 07/25/2008 04:58:04 MDTNo reproduction or networking permitted without license from IHS -,-,- 4 61076-2-104 IEC:2008 Table 13 Test group BP .32 Table 14 Test group CP .33 Table 15 Test group DP .34 Table 16 Test group EP .34 Copyright International Electrotechnical Commission Provided by IHS un
36、der license with IECLicensee=Boeing Co/5910770001 Not for Resale, 07/25/2008 04:58:04 MDTNo reproduction or networking permitted without license from IHS -,-,- 61076-2-104 IEC:2008 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ CONNECTORS FOR ELECTRONIC EQUIPMENT PRODUCT REQUIREMENTS Part 2-104: Circ
37、ular connectors Detail specification for circular connectors with M8 screw-locking or snap-locking FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object
38、 of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications
39、 (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaisin
40、g with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express,
41、as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees
42、in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Com
43、mittees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking
44、 procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants o
45、r agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, us
46、e of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that
47、some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61076-2-104 has been prepared by subcommittee 48B: Connectors, of IEC technical committee 48: Electromechanica
48、l components and mechanical structures for electronic equipment. This part of IEC 61076-2 cancels and replaces the following parts of IEC 61076-2-101:2003 (first edition of IEC 61076-2-101): subclauses 2.2.3, 2.2.4 and 3.2.2, Tables 6, 10 and 12, any reference to connector type E and M8. Copyright International Electrotechnical Commission Provided by I