《BS-5442-3-1979.pdf》由会员分享，可在线阅读，更多相关《BS-5442-3-1979.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 5442-3: 1979 Classification of Adhesives for construction Part 3: Adhesives for use with wood UDC 006.72:665.93:691.11 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 15:59:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5442-3:1979 This British Standard, having been prep
2、ared under the direction of the Adhesives Standards Committee, was published under the authority of the Executive Board on 31 January 1979 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference ADC/10 Draft for comment 78/52175 DC ISBN 0 580 10530 X Coopera
3、ting organizations The Adhesives Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: Association of British Plywood and Veneer Manufacturers British Adhesive
4、Manufacturers Association* British Furniture Manufacturers Federated Associations* British Paper Bag Federation British Plastics Federation* British Woodworking Federation* Department of the Environment (Building Research Establishment, Princes Risborough Laboratory)* Department of Industry (Chemica
5、ls and Textiles) Federation of Gelatine and Glue Manufacturers Limited Ministry of Defence* Royal Institute of British Architects Society of Chemical Industry Wall Paper Manufacturers Ltd The organizations marked with an asterisk in the above list, together with the following, were directly represen
6、ted on the committee entrusted with the preparation of this British Standard: British Chemical and Dyestuffs Traders Association British Railways Board British Rubber Manufacturers Association Furniture Industry Research Association Timber Research and Development Association Amendments issued since
7、 publication Amd. No.Date of issueComments Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 15:59:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5442-3:1979 BSI 07-1999i Contents Page Cooperating organizationsInside front cover Forewordii 1Scope1 2References1 3Definition1 4Classification1 5C
8、ode for suitability of adhesives for Table 16 Table 1 Summary of classification of adhesives for wood/wood combinations2 Table 2 Summary of classification of adhesives for non-wood sheet material/wood combinations4 Publications referred toInside back cover Licensed Copy: sheffieldun sheffieldun, na,
9、 Mon Dec 04 15:59:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5442-3:1979 ii BSI 07-1999 Foreword This Part of this British Standard has been prepared under the direction of the Adhesives Standards Committee. Parts 1 and 2 of this British Standard deal, respectively, with adhesives for flooring
10、 and for interior wall and ceiling coverings. A number of adhesives for the site-bonding of timber and wood-based materials fall within the scope of these Parts of the standard. In addition adhesives are widely used for the fabrication of external and internal wood joinery and of timber fitments, an
11、d a number of wood-based materials used in construction are manufactured using adhesives. The conditions to which the adhesive bonds of such fitments and materials are exposed in construction vary widely, particularly in respect of the degree of exposure to moisture and, therefore, the corresponding
12、 hazard to the bond. Part 3 of this standard, therefore, provides guidance on the suitability of wood adhesives in relation to the conditions to which adhesives bonds may be exposed during the construction and use of buildings, and in other situations, both for joints fabricated on site and in the f
13、actory, and for manufactured materials such as plywood and wood particle board. In respect of the latter materials, attention is drawn to BS 1088 the choice, however, for any particular case, depends on economic and practical factors. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 15:59:09 G
14、MT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5442-3:1979 6 BSI 07-1999 Key to Table 1 and Table 2 1. Bone, skin and hide glue. Animal glue that complies with the requirements of BS 745. 2. Casein. Adhesives that comply with the requirements of BS 1444. 3 to 5. Phenol-formaldehyde, resorcinol-formald
15、ehyde, and resorcinol/phenol-formaldehyde. Adhesives based on phenolic synthetic resins derived from the reaction of the phenolic materials named with formaldehyde and complying with the requirements of type WBP of BS 1203:1979 and BS 1204-1 as appropriate. 6 to 8. Urea-formaldehyde, urea/melamine-f
16、ormaldehyde and melamine-formaldehyde. Adhesives based on amino-plastic synthetic resins derived from the reaction of urea, thiourea, melamine or allied compounds, or mixtures of these compounds with formaldehyde, and complying with the requirements of types BR or MR of BS 1203:1979 or BS 1204-1 and
17、 BS 1204-2:1979 as appropriate. 9. Polyvinyl acetate emulsion (cross-linkable). Adhesives based on an aqueous emulsion of a polyvinyl acetate resin which contains in each molecule reactive groups capable of being cross-linked by the addition before application of a catalyst as a second component. 10
18、. Epoxide resin. Adhesives based on a two-component system consisting of liquid epoxide resin and liquid hardener both of which may contain fillers, and which are mixed immediately before use. 11. Unsaturated polyester. Adhesives based on a blend of a poly-condensation product of saturated and unsat
19、urated dicarboxylic acids and polyhydric alcohols with styrene or other unsaturated monomer with accelerator catalyst, fillers and structuring agents and supplied as a multi-component material requiring mixing immediately before use. 12 to 15. Elastomeric contact adhesives. Adhesives based on a solu
20、tion of the named elastomer, together with modifying resins and stabilizers in organic solvents. Some members of this group are reactive, and may be cross-linked by the addition of a second component before application. 16 to 19. Elastomeric gap-filling adhesives. Adhesives based on a solution of th
21、e named elastomer, together with modifying resins, in organic solvent, and containing fillers to produce a paste-like consistency. 20 to 23. Hot-melt adhesives. Adhesives based on thermo-plastic resin blends, substantially based on the named polymer, and possibly containing pigments or fillers, appl
22、ied molten, and developing their adhesive strength simply by cooling. 24. Polychloroprene latex. Adhesives based on an aqueous dispersion of polychloroprene elastomer and synthetic resins possibly containing fillers. 25. Polyvinyl acetate and polyvinyl acetate copolymer emulsion. Adhesives based on
23、an aqueous emulsion of polyvinyl acetate homopolymers or copolymers, which may contain fillers, and satisfying the requirements of BS 4071. 26. Acrylate polymer emulsion. Adhesives based on an acrylate ester copolymer emulsion which may contain resin modifiers and/or fillers. 5 Code for suitability
24、of adhesives for Table 1 NOTE 1Where a D code is given in the table, it is understood to be suitable also for conditions under A and BC. Similarly a BC code is suitable for conditions under A. NOTE 2The first line of Table 1 gives the highest suitability coding that can be obtained with some members
25、 of the class of adhesives indicated, provided that the adherends are also suitable for the degree of exposure indicated in that coding. NOTE 3Certain urea formaldehyde-based adhesives which comply with the requirements of type MR of BS 1204-1 and BS 1204-2 have been found suitable for applications
26、where the moisture content of natural softwood can exceed 18 % in service but which does not remain at this figure continuously; they are suitable also where joints are protected by paint films and are not subjected to loads. These adhesives are generally found to give satisfactory service in situat
27、ions where the temperature may exceed 50 C. For those applications marked with an asterisk in Table 1, it is recommended that the urea formaldehyde-based adhesive should comply with the above requirement. NOTE 4For assembling components on site the adhesives and conditions should not be inferior to
28、those used for factory assembly. ASuitable for service inside heated and ventilated buildings and in other environments where the equilibrium moisture content of natural softwood does not exceed 18 % and the bond-line remains below a temperature of 50 C. BC Suitable for exposure conditions intermedi
29、ate between A and D bearing in mind that any given set of exposure conditions can have different results depending upon the type of wood and on the article or fabrication in question. DSuitable for full exposure to weather or to water immersion. SCould be suitable in special cases, but is not used i
30、n general practice. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 15:59:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5442-3:1979 BSI 07-1999 Publications referred to BS 476, Fire tests on building materials and structures. BS 745, Animal glue for wood (joiners glue) (dry glue; jelly or
31、liquid glue). BS 1088 & BS 4079, Plywood for marine craft1). BS 1186, Quality of timber and workmanship in joinery. BS 1186-2, Quality of workmanship. BS 1203, Synthetic resin adhesives (phenolic and aminoplastic) for plywood. BS 1204, Synthetic resin adhesives (phenolic and aminoplastic) for wood.
32、BS 1204-1, Gap-filling adhesives. BS 1204-2, Close-contact adhesives. BS 1444, Cold-setting casein adhesive powders for wood. BS 1455, Plywood manufactured from tropical hardwoods1). BS 1811, Methods of test for wood chipboards and other particle boards. BS 2604, Resin-bonded wood chipboard. BS 3444
33、, Blockboard and laminboard1). BS 4071, Polyvinyl acetate (PVA) emulsion adhesives for wood. BS 4169, Glue-laminated timber structural members. BS 5291, Finger joints in structural softwood. BS 5442, Classification of adhesives for construction. BS 5442-1, Adhesives for use with flooring materials1)
34、. BS 5442-2, Adhesives for use with interior wall and ceiling coverings (excluding decorative flexible materials in roll form)1). 1) Referred to in the foreword only. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 15:59:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5442-3: 1979 BSI 389 Ch
35、iswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updat
36、ed by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British
37、Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the lat
38、est editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of t
39、hose that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information serv
40、ices are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For de
41、tails of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the C
42、opyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing
43、the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 15:59:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI