《BS-5131-2.6-1979.pdf》由会员分享，可在线阅读，更多相关《BS-5131-2.6-1979.pdf（8页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 5131-2.6: 1979 Methods of test for Footwear and footwear materials Part 2: Solings Section 2.6 Split tear strength of cellular solings NOTEIt is recommended that this Section should be read in conjunction with the information in the General introduction to BS 5131, published sepa
2、rately. UDC 685.31:620.1:685.312.122:539.412.1 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:59:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5131-2.6:1979 This British Standard, having been prepared under the direction of the Clothing Standards Committee, was published under the auth
3、ority of the Executive Board on 31 January 1979 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference CLT/7 Draft for comment 77/35353 DC ISBN 0 580 10627 6 A British Standard does not purport to include all the necessary provisions of a contract. Users of
4、 British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. This standard
5、has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:59:35 GMT+00:00 2006, U
6、ncontrolled Copy, (c) BSI BS 5131-2.6:1979 BSI 09-1999i Contents Page 1Scope1 2Reference1 3Principle1 4Apparatus1 5Test pieces1 6Conditioning and testing atmosphere1 7Procedure1 8Calculation and expression of results2 9Test report2 Figure 2.6/1 Knife and splitting jig2 Figure 2.6/2 Test piece after
7、preparation for test showing position of splits and reference lines3 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:59:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:59:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5131-
8、2.6:1979 BSI 09-19991 1 Scope This Section describes a method for determining the split tear strength of all types of flexible cellular solings. The test can also be used for solid and semi-expanded solings but in these cases may be of limited application owing to the tendency of the tear to run qui
9、ckly to one surface giving misleading results. This can also occur, but to a lesser extent, with cellular solings. NOTESection 2.6 is based on SATRA1) Physical Test Method PM 65. 2 Reference This Section refers to the following standards publication: BS 5131, Methods of test for footwear and footwea
10、r materials Section 2.7: Preparation of soling test pieces (in course of preparation). 3 Principle A test piece is split for part of its length parallel to the surface of the rubber so that the split is midway between the two surfaces. The two tabs so formed are pulled apart and the maximum force re
11、quired to propagate the split as a tear is determined. 4 Apparatus The following apparatus is required. 4.1 A low-inertia type tensile machine, preferably autographic, with a constant rate of traverse of 100 20 mm/min, a force range of 0 to 200 N and preferably higher and lower ranges also. 4.2 A sp
12、litting jig and knife to use for making the initial cuts. NOTEThe SATRA knife and jig STD 191 are suitable and are illustrated diagrammatically in Figure 2.6/1. 5 Test pieces Cut rectangles each measuring 75 mm 25 mm, three in the direction along the soles or sheet material and three at right angles
13、 to this from samples which have already been reduced to the standard testing thickness for cellular solings of 5.0 0.2 mm by the procedure described in BS 5131-2.7. Using the splitting jig and knife, split one end of each test piece half-way between the top and bottom surfaces for a distance of app
14、roximately 15 mm. (The split should not be longer than 20 mm and the test is difficult if it is less than 12 mm.) Make sure the split portion ends in a clean cut. This forms two tongues at the end and leaves a piece approximately 60 mm 25 mm intact. Turn the test piece round and cut the other end in
15、 the same way so that two ends are split and the centre portion is not. Draw two lines across the test piece 12 mm beyond the end of each split portion. A prepared test piece is then as shown in Figure 2.6/2. 6 Conditioning and testing atmosphere Condition the test material for at least 6 h at 20 2
16、C after reducing it to the standard thickness and carry out the test in this atmosphere. The time interval between cutting out the test pieces and testing is not critical. 7 Procedure 7.1 Select the force range most suitable for the test; usually this is the 0 to 200 N range but occasionally strong
17、materials give results above 200 N and for very weak materials it may be desirable to use a 0 to 100 N range to improve the accuracy of the results. Fold back the two tongues at one end of the test piece and insert and clamp one in each jaw of the machine. 7.2 Start the machine so that the jaws sepa
18、rate at 100 mm/min, and record a trace of the force as the test continues. If autographic force recording is not available on the tensile machine being used, set it to show the maximum force reached during the test. When the test piece has been torn for 12 mm, which will be indicated by the line acr
19、oss the test piece, stop the test. The test piece might however tear to one surface before the 12 mm tear length is completed, in which case this is noted and the maximum force reached is measured. Clamp the other end of the test piece in the jaws and test in the same way. 1) Shoe and Allied Trades
20、Research Association. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:59:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5131-2.6:1979 2 BSI 09-1999 7.3 Repeat for other test pieces cut in the same direction. 7.4 Test the test pieces cut in the other direction, in the same way. 8 Calculat
21、ion and expression of results 8.1 For each direction of test record the highest force observed for each of the six tears and take the arithmetic mean of the three highest results. Divide this mean by the width of the test piece (25 mm) and record the split tear strength in that direction as N/mm wid
22、th, to one decimal place. 8.2 State how many (if any) of the three results contributing to the average were for tests which had torn to one surface within the specified 12 mm. 9 Test report Include the following items in the test report: a) the average tearing strength per unit width (split tear str
23、ength) for each direction, tested in accordance with 8.1; b) the number of test results in which the tear ran to one surface, in accordance with 8.2; c) the nature and full identification of the sample(s); d) reference to the method of test (i.e. BS 5131-2.6); e) the date of testing. Figure 2.6/1 Kn
24、ife and splitting jig Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:59:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5131-2.6:1979 BSI 09-19993 Figure 2.6/2 Test piece after preparation for test showing position of splits and reference lines Licensed Copy: sheffieldun sheffieldun, na,
25、 Mon Dec 04 13:59:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5131-2.6: 1979 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the int
26、ernational level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services.
27、 We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individu
28、al updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response t
29、o orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its
30、Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standar
31、ds developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of t
32、he publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior writ
33、ten permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:59:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI