《BS-5649-2-1978 EN-40-2-1976.pdf》由会员分享，可在线阅读，更多相关《BS-5649-2-1978 EN-40-2-1976.pdf（20页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 5649-2: 1978 EN 40-2 Incorporating Amendment No. 1 Specification for Lighting columns Part 2: Dimensions and tolerances This European Standard EN 40-2 was given, as from 30 November 1978, the status of a British Standard and will replace the relevant requirements of BS 1308, BS 1
2、840 and BS 3989 (see national foreword) UDC 624.971:628.971:621.753.1 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5649-2:1978 This British Standard was published under the authority of the Executive Board on 30 November 1978 BSI 09-19
3、99 The following BSI references relate to the work on this standard: Committee reference RDB/28 Draft for comment 74/41655DC ISBN 0 580 10403 6 Cooperating organizations The European Committee for Standardization, under whose supervision this European Standard was prepared, comprises the national st
4、andards organizations of the following Western European countries: Austriasterreichisches Normungsinstitut BelgiumInstitut Belge de Normalisation DenmarkDansk Standardiseringsraad FinlandSuomen Standardisoimisliitto, r.y. FranceAssociation Franaise de Normalisation GermanyDeutsches Institut fr Normu
5、ng E.V. IrelandInstitute for Industrial Research and Standards ItalyEnte Nazionale Italiano di Unificazione NetherlandsNederlands Normalisatie-instituut NorwayNorges Standariseringsforbund PortugalRepartio de Normalizao SpainInstituto Nacional de Racionalizacin y Normalizacin SwedenStandardiseringsk
6、ommissionen i Sverige SwitzerlandAssociation Suisse de Normalisation United KingdomBritish Standards Institution Amendments issued since publication Amd. No.Date of issueComments 3136December 1979 Indicated by a sideline in the margin Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 G
7、MT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5649-2:1978 BSI 09-1999i Contents Page Cooperating organizationsInside front cover National forewordii Brief history2 Foreword2 1Scope and field of application3 2Post top columns, main dimensions4 3Columns with brackets, main dimensions5 4Door openings an
8、d cable entry slots6 5Column foundation, planting depth and base plate7 6Flange plate8 7Connection dimensions for lanterns9 8Tolerances10 Annex11 National particularities11 National appendix A11 National appendix B11 National appendix C12 Figure 14 Figure 25 Figure 3 Position of door and cable entry
9、 slot6 Figure 4 Dimensions of cutout6 Figure 5a7 Figure 5b7 Figure 68 Figure 78 Figure 88 Figure 9a9 Figure 9b9 Figure 10a9 Figure 10b9 Figure 1110 Table 1 Factor G11 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5649-2:1978 ii BSI 09-1
10、999 National foreword This BS/EN is being produced in the following Parts: Part 1: Definitions and terms; Part 2: Dimensions and tolerances; Part 3: Materials1); Part 4: Surface protection of metal columns1); Part 5: Base compartment and cableways1); Part 6: Loads1); Part 7: Verification of structur
11、al design by calculations1); Part 8: Verification of structural design by testing1); Part 9: Special requirements for concrete columns1). A further Part dealing with special requirements for plastics columns is in an early stage of preparation. BS 5649 will be issued in Parts as they are completed a
12、nd approved, and until the whole document is published it will not be possible to supersede the present British Standards for lighting columns. As the Parts are issued recommendations will be given for their implementation together with a list of clauses in the existing standards which they will eve
13、ntually supersede. It is hoped that a gradual change-over will be obtained which will terminate with the total withdrawal of the existing standards. The British Standards affected are: BS 1308:1970, Specification for concrete street lighting columns. BS 1840:1960, Specification for steel columns for
14、 street lighting. BS 3989:1966, Specification for aluminium street lighting columns. It is anticipated that the affected clauses in the existing standards will be withdrawn in accordance with the following timetable: BS 1840 and BS 3989, One year from the publication of this Part of this standard. B
15、S 1308, Three years from the publication of Parts 6, 7, 8 and 9 of this standard. In the interim period it is permissible for dimensions and tolerances for lighting columns to be based on either the existing standards or on BS 5649-2. Purchasers specifying lighting schemes during the interim period
16、should, where possible, permit either alternative. BS 5649-2 covers some or all of the requirements also covered in the following clauses of the existing British Standards: BS 1308 1) In course of preparation 1.1Scope 1.8.2Straightness tolerances 1.8.3Column height and bracket projection 1.10Bracket
17、 projection 1.11Lantern fixing 1.12.1 Door and door opening 1.18Service connections Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5649-2:1978 BSI 09-1999iii BS 1840 BS 3989 This standard includes columns of height greater than those tha
18、t were envisaged in the scope of the existing BS 1308, BS 1840 and BS 3989. It is therefore inappropriate to use the design loading requirements in these British Standards for columns over 15 m in nominal height; for such columns the loading requirements should be agreed between the purchaser and th
19、e supplier, pending the issue of other Parts of this standard. Advice regarding the choice of planting depth is given in National appendix B. Convention. In this European Standard the comma has been used as a decimal marker. In British Standards it is current practice to use a full point on the base
20、line as the decimal marker. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. 1Scope 5Toler
21、ances 6Doors and door openings 8Base-plates 10Service slots 11Relative positions of door openings, service slots and bracket arms 12Recommended depth of columns in the ground 13Lantern fixing 1Scope 6Tolerances 8a)Doors and door openings 9Base-plate 11Service slot 12Relative positions of bracket arm
22、, door opening and service slot 13Recommended depths of columns in the ground 14Lantern fixing Summary of pages This document comprises a front cover, an inside front cover, pages i to iv, the EN title page, pages 2 to 12 and a back cover. This standard has been updated (see copyright date) and may
23、have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 200
24、6, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 40-2 Edition 1 June 1976 UDC 624.971:628.971:621.753.1 Key words: Luminaire, lighting column, dimension, dimensional tolerance English version Lighting columns Part 2: Dimensions and tolerances Candlabres Dimensions e
25、t tolrances Lichtmaste Masse und zulssige Abweichungen This European Standard was accepted by CEN on 1976-06-30. The CEN members are bound to adhere to the CEN Internal Regulations which specify under which conditions this European Standard has to be given, without any alteration, the status of a na
26、tional standard. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member. This European Standard is established by CEN in three official versions (English, French, German). A translation mad
27、e by another member under its own responsibility, in its own language, and notified to CEN has the same status. CEN members are the national standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and U
28、nited Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels Copyright reserved to all CEN members Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncon
29、trolled Copy, (c) BSI EN 40-2 BSI 09-1999 2 Brief history This European Standard, drawn up by technical committee CEN/TC 50 “Lighting poles and spigots” (secretariat DIN), was submitted to the ballot of CEN members in February 1976 with a view to its adoption as a European Standard. It was adopted a
30、s such by CEN on 30 June 1976 on the strength of its acceptance by the following member countries: Austria, France, Germany, Ireland, Italy, Netherlands, Portugal, Switzerland, United Kingdom. Foreword In producing this Part of this standard it was recognized that columns with nominal heights and/or
31、 bracket projections not specified in this standard will still be needed to replace columns in existing lighting schemes. However, all columns for new lighting schemes should be selected from the nominal heights and bracket projections specified in this document. Licensed Copy: sheffieldun sheffield
32、un, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 40-2 BSI 09-19993 1 Scope and field application This European Standard specifies the dimensions and tolerances for a chosen series of lighting columns adopted by CEN. It relates to post top columns for post top lanterns as wel
33、l as columns with brackets for side entry lanterns. The dimensional requirements are specified except that the connection dimensions in clause 7 represent, for the time being, a recommended choice. It is proposed to make them mandatory after an interim period. Licensed Copy: sheffieldun sheffieldun,
34、 na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 40-2 4 BSI 09-1999 2 Post top columns, main dimensions (in metres) Figure 1 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 40-2 BSI 09-19995 3 Columns with brackets,
35、main dimensions (in metres) Figure 2 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 40-2 6 BSI 09-1999 4 Door openings and cable entry slots (dimensions in millimetres) Figure 4 Dimensions of cutout Figure 3 Position of door4) and cable
36、entry slot 1) Supplementary dimensions for concrete columns. 2) For metal columns only. 3) It is recommended that this dimension be approximately 600, but in no case shall it be less than 300; no maximum is specified. 4) It is recommended that the door opening is positioned parallel to the bracket o
37、n the side away from the direction of traffic. Figure 3 shows the position for right hand drive roads. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 40-2 BSI 09-19997 5 Column foundation, planting depth and base plate (dimensions in mil
38、limetres) Figure 5a Figure 5b 1) The planting depth, e, shall be selected from the values given in the table taking into consideration the calculations made beforehand and the ground conditions. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BS
39、I EN 40-2 8 BSI 09-1999 6 Flange plate (dimensions in millimetres) Figure 6 Figure 7 Figure 8 h m csa min. ad1a u 52608200M18 u 1240010300M24 u 20 400 500 20 300 400 M27 d1a d2 la min. M1822400 M2430500 M2733700 a These dimensions shall be checked by calculation. Licensed Copy: sheffieldun sheffield
40、un, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 40-2 BSI 09-19999 7 Connection dimensions for lanterns (in millimetres)2) 2) See clause 1. d1bl1 6070 76130 102250 Figure 9a Figure 9b a Post top lanterns d2b l2 42100 60 100 250 Figure 10a Figure 10b a Side entry lanterns a T
41、his design does not apply to concrete columns. b Diameters of steel spigots should be as given in the International Standard of ISO 64:1974 “Steel tubes, outside diameters” for steel tubes of the nearest size. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontroll
42、ed Copy, (c) BSI EN 40-2 10 BSI 09-1999 8 Tolerances 8.1 Straightness x u 0,003 l; l = h + e %x u 0,003 %l; %l W 1 m See Figure 11. Measurement shall be carried out in unloaded state (column lying horizontally). 8.2 Total length of post top columns 8.2.1 Longitudinally welded columns 8.2.2 Seamless
43、columns 8.3 Total length of columns with brackets 8.4 Projection (without spigot) 2 % 8.5 Fixing angle The tolerance for the fixing angle of the lantern fixing axis, from the horizontal, shall be 2 when not under load; the deviation between the bracket axis and lantern fixing axis shall also not exc
44、eed2. 8.6 Door opening and cable entry slot 8.7 Column cross-section 8.7.1 Metal columns 8.7.1.1 Column circumference tolerance: 1 % 8.7.1.2 Deviation in shape 8.7.1.2.1 Circular cross-section: 3 % of the diameter calculated from the measured circumference (disregarding a welded seam bead) 8.7.1.2.2
45、 Polygonal cross-section: 4 % of the nominal value over the flats of the polygon 8.7.2 Concrete columns 8.7.2.1 Column circumference tolerance: 1 % 8.7.2.2 Deviation in shape Cross-section dimensional tolerances: 5 %, min. value 10 mm 8.8 Connection dimensions for lanterns 8.8.1 Length of lantern co
46、nnection for l1 or l2: 2 mm 8.8.2 Diameter of lantern connection (ungalvanized) for d1 or d2: see ISO 64:1974 Figure 11 With planted section:0,5 % or 25 mm With flange plate: 0,6 % (the greater value shall apply) With planted section:0,5 % or 50 mm With flange plate: 0,6 % (the greater value shall a
47、pply) Column with planted section:1 % Column with flange plate: 1,2 % For the opening dimensions:+ 5 mm 0 mm Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 16:30:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 40-2 BSI 09-199911 Annex National particularities In France it is admissible to u
48、se in addition to the bracket projections fixed in clause 3 also the bracket projections w = 1 m and w = 1,5 m. National appendix A The United Kingdom participation in the preparation of this European Standard came under the direction of the Road Engineering Standards Committee of BSI. The following
49、 organizations were involved in the work on this standard: Aluminium Federation Association of Public Lighting Engineers British Plastics Federation British Precast Concrete Federation Ltd. British Steel Industry Cement and Concrete Association County Surveyors Society Department of Transport Design Council Electricity Supply Industry in England and Wales Institution of Highway Engineers Institution of Mechanical Engineers Institution of Municipal Engineers Lighting Column Manufa