《ISO-10911-1994.pdf》由会员分享,可在线阅读,更多相关《ISO-10911-1994.pdf(5页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 10911 First edition 1994-l I-1 5 Solid hardmetal end mills with parallel shank - Dimensions Fraises cylindriques deux tail/es monobloc en mktaux-durs - Dimensions Reference number IS0 10911 :I 994(E) Copyright International Organization for Standardization Provided by IHS
2、under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 04:58:21 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 10911:1994(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of nationa
3、l standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internation
4、al organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committee
5、s are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 10911 was prepared by Technical Committee lSO/TC 29, Small too/s, Subcommittee SC 9, Tools with cutting edges
6、made of hard cutting materials. 0 IS0 1994 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Interna
7、tional Organization for Standardizatron Case Postale 56 l CH-1211 Geneve 20 . Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 04:58:21 MDTNo
8、 reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD 8 IS0 IS0 10911:1994(E) Solid hardmetal end mills with parallel shank - Dimensions 1 Scope This International Standard specifies the dimensions of solid hardmetal end mills with parallel shank. The designatio
9、n of these end mills will be the subject of a future International Standard. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publi- cation, the edition indicated was valid. Al
10、l standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most re- cent edition of the standard indicated below. Mem- bers of IEC and IS0 maintain registers of currently valid International Standa
11、rds. IS0 3338-I :I 993, Parallel shanks for milling cutters - Part 1: Dimensional characteristics of plain parallel shanks. 3 Dimensions Dimensions of solid hardmetal end mills with plain parallel shank are specified in figure 1 and table 1. NOTE 1 The dimensions given in table 1 also apply to solid
12、 hardmetal end mills with flatted parallel shanks in ac- cordance with IS0 3338-2:1985, Parallel shanks for milling cutters - Part 2: Dimensional characteristics of flatted parallel shanks 4 Centre cutting End mills with two flutes shall be centre-cutting (slot drills). End mills with three flutes o
13、r more may be centre- cutting. 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 04:58:21 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 10911:1994
14、(E) Plain parallel shank IS0 3338-l (see note I) Figure 1 Table 1 Dimensions in millimetres I , 3 38 4 3 38 1.5 4 43 3 + 4 3 38 2 4 43 7 I 3 38 2.5 4 43 3 38 3 6 57 4 43 3,5 6 57 I I 4 43 4 6 57 I 7 8 63 8 8 63 9 10 72 I 76 12 12 83 14 14 83 I 26 16 16 89 18 18 92 20 20 101 tol. +1 0 Cutting diamete
15、r 4 h10 Shank diameter 4 1 Overall length 4 nom. tol. Cutting length h nom. I 1) For the tolerance, see IS0 3338-l I Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 04:58:21 MDTN
16、o reproduction or networking permitted without license from IHS -,-,- IS0 10911:1994(E) ICS 25.100.20 Descriptors: tools, cutting tools, milling cutters, end mills, dimensions, parallel shanks Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 04:58:21 MDTNo reproduction or networking permitted without license from IHS -,-,-