《BS-5667-15-1979 ISO-5041-1977.pdf》由会员分享，可在线阅读，更多相关《BS-5667-15-1979 ISO-5041-1977.pdf（8页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 5667-15: 1979 ISO 5041:1977 Specification for Continuous mechanical handling equipment Safety requirements Part 15: Unit loads: crate-carrying chain conveyors having biplanar chains for flat-bottomed unit loads ISO title: Continuous mechanical handling equipment for unit loads Cr
2、ate-carrying chain conveyors having biplanar chains for flat-bottomed unit loads Safety code UDC 621.867:614.8 + 621.867.1 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:42:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5667-15:1979 This British Standard, having been prepared under the
3、direction of the Mechanical Engineering Standards Committee, was published under the authority of the Executive Board on 31 January 1979 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference MEE/128 Draft for comment 76/72202 DC ISBN 0 580 10518 0 Cooperat
4、ing organizations The Mechanical Engineering Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: The organizations marked with an asterisk in the above list,
5、together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Associated Offices Technical Committee*Department of the Environment Association of Consulting Engineers*Department of Trade (Marine Division) Association of Hydraulic Equ
6、ipment Engineering Equipment Users Association* ManufacturersFederation of Manufacturers of Construction Association of Mining, Electrical and Equipment and Cranes Mechanical EngineersHealth and Safety Executive* British Compressed Air SocietyInstitution of Gas Engineers British Electrical and Allie
7、d Manufacturers Institution of Mechanical Engineers Association (BEAMA)Institution of Plant Engineers British Gas CorporationInstitution of Production Engineers* British Gear Manufacturers AssociationLondon Transport Executive British Internal Combustion Engine Machine Tool Trades Association Manufa
8、cturers AssociationMinistry of Defence British Pump Manufacturers AssociationNational Coal Board* British Steel CorporationOil Companies Materials Association British Steel IndustryProcess Plant Association Chartered Institution of Building ServicesRailway Industry Association of Great Britain Crown
9、 Agents for Oversea Governments and Society of Motor Manufacturers and Traders AdministrationsLimited Department of Industry (Mechanical Telecommunication Engineering and Engineering)Manufacturing Association (TEMA) Department of Industry (National Engineering Water-tube Boilermakers Association Lab
10、oratory) Amalgamated Union of Engineering WorkersElectricity Supply Industry in British Quarrying and Slag FederationEngland and Wales British Rubber Manufacturers AssociationInstitution of Mining and Metallurgy Chain Testers Association of Great BritainInstitution of Mining Engineers Coke Oven Mana
11、gers AssociationMechanical Handling Engineers Association Electrical, Electronic, Telecommunications and Metal Packaging Manufacturers Association Plumbing UnionSand and Gravel Association Limited Society of Dairy Technology Amendments issued since publication Amd. No.Date of issueComments Licensed
12、Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:42:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5667-15:1979 BSI 09-1999i Contents Page Cooperating organizationsInside front cover National forewordii 1Scope1 2Field of application1 3Reference1 4Special safety rules1 Publications referred toInsid
13、e back Cover Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:42:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5667-15:1979 ii BSI 09-1999 National foreword This British Standard has been prepared under the direction of the Mechanical Engineering Standards Committee. This Part is identic
14、al with ISO 5041 “Continuous mechanical handling equipment for unit loads Crate-carrying chain conveyors having biplanar chains for flat-bottomed unit loads Safety code”, developed by Technical Committee ISO/TC 101, Continuous mechanical handling equipment. This Part, which forms one of a series, im
15、plements the safety code and should be read in conjunction with BS 5667-1. Terminology and conventions. The text of the International Standard has been approved as suitable for publication, without deviation, as a British Standard. Some terminology and certain conventions are not identical with thos
16、e used in British Standards; attention is especially drawn to the following. Wherever the words “International Standard” appear, referring to this standard, they should be interpreted as “British Standard” Cross-references. The following International Standards are referred to in the text and for ea
17、ch there is a corresponding British Standard; these are as listed below: A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer i
18、mmunity from legal obligations. International StandardCorresponding British Standard ISO 1819:1977BS 5667 Specification for continuous mechanical handling equipment Safety requirements Part 1:1978 General (Identical) Summary of pages This document comprises a front cover, an inside front cover, page
19、s i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:42:50 GMT
20、+00:00 2006, Uncontrolled Copy, (c) BSI BS 5667-15:1979 BSI 09-19991 1 Scope This International Standard specifies, in addition to the general safety rules set out in ISO 1819, the special safety rules for the following continuous mechanical handling equipment for unit loads: crate-carrying chain co
21、nveyors having biplanar chains for flat-bottomed unit loads. 2 Field of application The safety rules laid down in this International Standard apply regardless of the use for which the equipment is intended. These safety rules limit the suppliers responsibility to continuous mechanical handling equip
22、ment properly so called, excluding the structures to which such equipment is fixed. 3 Reference ISO 1819, Continuous mechanical handling equipment Safety code General rules. 4 Special safety rules The design, construction and operation of crate-carrying chain conveyors having biplanar chains for fla
23、t-bottomed unit loads shall meet the legal and local requirements relating to safety in general (see Appendix Z of ISO 1819); the principles laid down in clause 1 of ISO 1819; the general rules laid down in clause 2 of ISO 1819; the following special rules. 4.1 In the construction stage (design and
24、manufacture) 4.1.1 All chain traction mechanism drives shall be equipped with a load limiter (with or without motor cut-out) which responds when the permissible traction force is exceeded, i.e. independently of the overload safety devices of the electrical switchgear. 4.1.2 In addition to rules 2.1.
25、2 and 2.1.3 of ISO 1819 relating to sloping or non-sloping conveyors, a safety device shall be provided (rods, or upper guides) if occasional lateral slipping of the materials can be foreseen under normal operating conditions. 4.2 During the installation stage (layout, erection and entry into servic
26、e) 4.2.1 The conveyors shall be erected and aligned with care. This applies not only to the framework but also to the mechanical components and the chains. 4.3 During the utilization stage (operation and maintenance) 4.3.1 The chain and its track shall be the subject of special attention and of regu
27、lar and correct lubrication. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:42:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 blank Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:42:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5667-15:1979 BSI 09-1999 Publications referred
28、 to See national foreword Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:42:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5667-15: 1979 ISO 5041:1977 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparin
29、g British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.
30、It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside f
31、ront cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be add
32、ressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide r
33、ange of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 711
34、1. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyrig
35、ht subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or
36、 by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for a
37、ny other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 13:42:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI