《ISO-12468-1-2003.pdf》由会员分享，可在线阅读，更多相关《ISO-12468-1-2003.pdf（30页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 12468-1:2003(E) ISO 2003 INTERNATIONAL STANDARD ISO 12468-1 First edition 2003-03-15 External exposure of roofs to fire Part 1: Test method Exposition des toitures un feu extrieur Partie 1: Mthode dessais Copyright International Organization for Standardization Provided by IHS
2、under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 12468-1:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file ma
3、y be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat acce
4、pts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that th
5、e file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any
6、form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749
7、09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking pe
8、rmitted without license from IHS -,-,- ISO 12468-1:2003(E) ISO 2003 All rights reserved iii Contents Page Forewordiv Introduction v 1 Scope1 2 Normative references .1 3 Terms and definitions.1 4 Symbols .3 5 Selection of test specimen pitch.3 6 Test specimens .4 6.1 General requirements.4 6.2 Select
9、ion of standard supporting elements.5 6.3 Positioning of joints6 6.4 Edge detailing7 7 Test equipment7 7.1 Exposure levels.7 7.2 Brands8 7.3 Wind10 7.4 Radiation10 7.5 Timing device 10 7.6 Calibration element.10 7.7 Specimen holder .10 7.8 Gas burner.14 7.9 Stand 15 8 Test conditions15 8.1 Test envi
10、ronment15 8.2 Calibration procedure.16 9 Conditioning and test preparation 16 9.1 Conditioning16 9.2 Protection of the edges17 10 Test procedure 17 10.1 General.17 10.2 Commencement of the test17 10.3 Ignition and positioning of the brands .18 10.4 End of the test .19 10.5 Post-test examination.19 1
11、1 Observations and measurements .19 11.1 General.19 11.2 External fire spread.19 11.3 Fire penetration.20 11.4 Opening20 11.5 Damage 20 12 Expression of test results20 13 Test report20 Annex A (normative) Direct field of application22 Copyright International Organization for Standardization Provided
12、 by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 12468-1:2003(E) iv ISO 2003 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldw
13、ide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on th
14、at committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in
15、accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard r
16、equires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12468-1 was prepared by Te
17、chnical Committee ISO/TC 92, Fire safety, Subcommittee SC 2, Fire containment. ISO 12468 consists of the following parts, under the general title External exposure of roofs to fire Part 1: Test method Part 2: Classification Copyright International Organization for Standardization Provided by IHS und
18、er license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 12468-1:2003(E) ISO 2003 All rights reserved v Introduction This part of ISO 12468 specifies a test method that relates to the effects o
19、f fires on roofs. The test method described in this part of ISO 12468 represents the effect of two levels of fire exposure. Level A: A large burning brand coming from a nearby building and falling onto the roof. Level A considers the effects of wind and additional radiant heat. Level B: A small burn
20、ing brand transported by the wind from a remote fire and falling onto the roof. Level B considers the effect of wind but without additional radiant heat. Any national regulation may refer to only one or both of the two levels of fire exposure. Copyright International Organization for Standardization
21、 Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/99807
22、55100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 12468-1:2003(E) ISO 2003 All rights reserved 1 External exposure of roofs to fire Part 1: Test method CAUTION The attention of all persons concerned with man
23、aging and carrying out this fire test is drawn to the fact that fire testing may be hazardous and that there is a possibility that toxic and/or harmful smoke and gases may be evolved during the test. Mechanical and operational hazards may also arise during the construction of the test elements or st
24、ructures, their testing and disposal of test residues. An assessment of all potential hazards and risks to health shall be made and safety precautions shall be identified and provided. Written safety instructions shall be issued. Appropriate training shall be given to relevant personnel. Laboratory
25、personnel shall ensure that they follow written safety instructions at all times. 1 Scope This part of ISO 12468 specifies a test method to determine the resistance of roofs to external exposure to fire. This method evaluates the behaviour of the roof when exposed to two types of burning brands comb
26、ined with wind and with or without heat radiation, concerning: a) the fire spread across the external surface of the roof; b) the fire spread within the roof; c) the fire penetration; d) the production of flaming droplets or debris falling through the roof, from the underside of the roof or from the
27、 exposed surface. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1394
28、3, Fire safety Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 13943 and the following apply. 3.1 assembly fabrication of materials and/or composites EXAMPLE Sandwich panels. Copyright International Organization for Standardization Provide
29、d by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 12468-1:2003(E) 2 ISO 2003 All rights reserved 3.2 burned material material that has been destroyed by combustion or pyrolys
30、is 3.3 composite combination of materials which are generally recognized in building construction as discrete entities EXAMPLE Coated or laminated product such as roofing felt. 3.4 continuous deck deck supporting the roof covering in which the gap between adjacent elements is not greater than 0,5 mm
31、 (5,0 mm in the case of wooden planks with plain edges) 3.5 damaged material material that has been burned, melted or otherwise visually changed by heat but does not include discoloration and soot deposits 3.6 exposed surface external surface of the calibration element or of the specimen which is su
32、bject to the heat conditions 3.7 external fire spread progression and extent of sustained flaming across the exposed surface of the specimen 3.8 fire penetration any opening, sustained flaming or glowing due to combustion on the underside that appears during the test and/or the occurrence of any fla
33、ming droplets or debris falling through the specimen or from the underside NOTE Charring or discoloration is not be regarded as fire penetration. 3.9 fire spread within the roof extent of burned material in each functional layer inside the specimen 3.10 flaming droplets or debris burning material fa
34、lling from or through the specimen that continues to burn on the floor for at least 5 s 3.11 internal damage extent of damaged material in each functional layer inside the specimen 3.12 material basic single substance or a uniformly dispersed mixture of substances EXAMPLE Metal, stone, wood, bitumen
35、, concrete or mineral wool. 3.13 measuring zone area of the specimen within which measurements are made Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking p
36、ermitted without license from IHS -,-,- ISO 12468-1:2003(E) ISO 2003 All rights reserved 3 3.14 opening any hole greater than 10 mm 10 mm that appears during the test which penetrates completely through the specimen 3.15 product material (3.12), composite (3.3) or assembly (3.1) about which informat
37、ion is required 3.16 profile pitch repeating length between sections of a uniformly corrugated or undulating roof deck 3.17 roof covering and sealing systems including any insulating layers or vapour barriers with their supporting elements and roof lights or other closures for roof apertures that ar
38、e intended to provide a weatherproof surface NOTE Elements with a slope greater than 70 are not considered as roofs in this part of ISO 12468. 3.18 roof covering material (3.12) attached to the deck 3.19 specimen representative section of the roof prepared for the purpose of test 3.20 sustained flam
39、ing flaming arising from an observed location, which persists for 5 s or longer 3.21 underside bottom surface of the specimen 4 Symbols Symbol Description Unit v1, v2, v3, v4, v5, v6, v7 Velocity of the air at the measuring points metres per second (m/s) Pitch (slope) degrees () 5 Selection of test
40、specimen pitch Roof systems designed for only one pitch shall be tested at the actual design pitch. Roof systems designed for more than one pitch shall be tested as follows: a) for pitch () less than 5, test at zero pitch; b) for pitch () from 5 to 20, test at 15; c) for pitch () greater than 20, te
41、st at 30. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 12468-1:2003(E) 4 ISO 2003 All rights reserved 6 T
42、est specimens 6.1 General requirements For each level of fire exposure, two specimens shall be tested with dimensions measuring 1 200 mm 10 mm in width 2 000 mm 10 mm in length for each test pitch. (See Figures 1 and 2.) When this is not possible due to the size of the roof light or other closure, a
43、 larger specimen shall be used. NOTE Roof lights cause difficulties due to their size, shape, composition and fire behaviour. Further guidance on the testing of roof lights will be presented in the next revision of this part of ISO 12468. The specimens shall be representative in all details of the r
44、oof in practice. Dimensions in millimetres with tolerances of 10 mm Key 1 radiant panel position 2 A Brands 3 measuring zone Figure 1 Measuring zone and position of the brands for Level A Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco
45、HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 12468-1:2003(E) ISO 2003 All rights reserved 5 Dimensions in millimetres with tolerances of 10 mm Key 1 measuring zone 2 B Brands Figure 2 Measuring zone and position of th
46、e brands for Level B 6.2 Selection of standard supporting elements 6.2.1 For continuous decks 6.2.1.1 General The test deck shall be selected in accordance with the following. a) In the case of roof coverings intended to be installed over a continuous deck other than a profiled metal deck, a roof de
47、ck in accordance with 6.2.1.2 or 6.2.1.4 shall be used. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/16/2007 10:05:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1246
48、8-1:2003(E) 6 ISO 2003 All rights reserved b) If the materials will only be laid over a profiled metal deck, then a trapezoidal profiled metal deck, in accordance with 6.2.1.3, shall be used as the deck. 6.2.1.2 Wood particleboard decks 6.2.1.2.1 The wood particleboard shall consist of wood particles bon