《ISO-13486-1-1999.pdf》由会员分享，可在线阅读，更多相关《ISO-13486-1-1999.pdf（16页珍藏版）》请在三一文库上搜索。
1、A Reference number ISO 13486-1:1999(E) INTERNATIONAL STANDARD ISO 13486-1 First edition 1999-10-01 Road vehicles Hydraulic braking systems Part 1: Double-flare pipes, tapped holes, male fittings and tube seats Vhicules routiers Dispositifs de freinage hydraulique Partie 1: Tuyauteries double renflem
2、ent, logements, raccords mles et sige-guides rapports -,-,- ISO 13486-1:1999(E) ISO 1999 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without per
3、mission in writing from the publisher. International Organization for Standardization Case postale 56 CH-1211 Genve 20 Switzerland Internetisoiso.ch Printed in Switzerland ii ContentsPage 1 Scope1 2 Normative references1 3 Pipes .1 3.1 Pipe without flares1 3.2 Double-flare pipes.1 3.3 Material requi
4、rements.1 3.4 Condition.1 4 Type A male fittings and type AS tapped holes3 4.1 Type A male fittings3 4.2 Type AS tapped holes 4 5 Type B male fittings and type BS tapped holes5 5.1 Type B male fittings5 5.2 Type BS tapped holes 6 6 Tube seats8 7 Marking.9 8 Identification statement 10 Bibliography11
5、 -,-,- ISOISO 13486-1:1999(E) iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body int
6、erested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnic
7、al Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publicat
8、ion as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 13486-1 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 2, Braking systems and equipment. ISO 13486 consists of the following parts, under
9、 the general title Road vehicles Hydraulic braking systems: Part 1: Double-flare pipes, tapped holes, male fittings and tube seats Part 2: Flare-to-flare connections -,-,- -,-,- INTERNATIONAL STANDARD ISOISO 13486-1:1999(E) 1 Road vehicles Hydraulic braking systems Part 1: Double-flare pipes, tapped
10、 holes, male fittings and tube seats 1 Scope This part of ISO 13486 specifies the essential dimensional and physical characteristics for double flares of metallic pipes (with and without surface protection), tapped holes, male fittings, and driving fit seats used in hydraulic braking systems for roa
11、d vehicles. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 13486. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to
12、 agreements based on this part of ISO 13486 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registe
13、rs of currently valid International Standards. ISO 4038:1996, Road vehicles Hydraulic braking systems Simple flare pipes, tapped holes, male fittings and hose end fittings. ISO 9227:1990, Corrosion tests in artificial atmospheres Salt spray tests. 3 Pipes 3.1 Pipe without flares Double-walled, rolle
14、d pipes shall be in accordance with ISO 4038 and Table 1. 3.2 Double-flare pipes Double-flare pipes shall meet the requirements of Figure 1 and Table 2. 3.3 Material requirements The material shall meet the requirements of Table 3. 3.4 Condition The inner and outer surfaces shall be free from oxidat
15、ion. The outer surface shall be protected against corrosion and shall withstand the salt spray test according to ISO 9227 for at least 96 h. -,-,- ISO 13486-1:1999(E) ISO 2 Table 1 Pipes Dimensions and tolerances in millimetres Outside diameter without nom.6,35 surface protection a, D1tol. 0,07 Wall
16、 thickness, B1 nom.0,7 tol. 0,07 Outside diameter, with surface protection, D1max.6,57 Minimum burst pressureMPa85 Average mass per metrekg/m0,1 NOTE Pipes with additional plastic coatings may be used; however, these pipes shall be compatible with male fittings, tapped holes, and flares as specified
17、 in this part of ISO 13486. a In this context, a “bare pipe“ means a pipe without surface treatment (nevertheless pipes which have been manufactured from surface- treated sheet material are considered as bare pipes). Dimensions in millimetres a Minimum sealing surface. Figure 1 Double-flare pipe -,-
18、,- ISOISO 13486-1:1999(E) 3 Table 2 Double-flare pipe Dimensions Dimensions in millimetres D1B1 0,07 B2 0,2 B3 min. D2 0,3 D3 0,35 E1 min. 4,750,71,416,93,3519 60,71,418,44,5521 6,350,71,418,854,8521 80,71,41,610,86,5521 100,71,41,613,38,5521 Table 3 Material requirements MaterialSteel Tensile stren
19、gth a, MPa 290 Yield strength, MPa 200 Percentage elongation at break a 25 a For pipes which are to be bent. 4 Type A male fittings and type AS tapped holes 4.1 Type A male fittings Type A male fittings shall meet the requirements of Figure 2 and Table 4. The inner and outer surfaces shall be free f
20、rom oxidation. The outer surface shall be protected against corrosion and shall withstand the salt spray test according to ISO 9227 for at least 96 h. Dimensions in millimetres Surface roughness values in micrometres a Depending on manufacturing methods, an undercut is optional. Figure 2 Type A male
21、 fitting -,-,- ISO 13486-1:1999(E) ISO 4 Table 4 Type A male fitting Dimensions Dimensions in millimetres D1 aD4 b D5D6D7EL1L2L3S 0 015+ , 6g 0 01+ , 0,2 js14min.nom.tol. 4,754,98 M10 1 6,87,811,5165910 022 0, 6,356,59 M12 1 8,49,413,9176912 88,29 M14 1,5 10,411,416,220,5611,514 027 0, 1010,29 M16 1
22、,5 12,413,419,622,5811,517 a Type A male fittings are not applicable to D1 = 6 mm. b Depending on the thickness of the surface protection of the pipe, diameter D4 may be adapted according to the agreement between manufacturer and user. 4.2 Type AS tapped holes Type AS tapped holes shall meet the req
23、uirements of Figures 3 and 4, and Table 5. Dimensions in millimetres Surface roughness values in micrometres Figure 3 Type AS 1 tapped hole -,-,- ISOISO 13486-1:1999(E) 5 Dimensions in millimetres Key 1Tube seat (see clause 6) Figure 4 Type AS 2 tapped hole Table 5 Type AS tapped hole Dimensions Dim
24、ensions in millimetres D1 a, b D5 6H D9D10 0,3 D11 0,05 0,15 + + L5L6 0,5 L7 min. L8 min. 4,75 M10 1 3,23,859,57,568,5 6,35 M12 1 4,55,36,49,57,568,5 8 M14 1,5 5,56,87,611,59,5810,5 10 M16 1,5 7,58,89,511,59,5810,5 a For indication only. b Type AS tapped holes are not applicable to D1 = 6 mm. 5 Type
25、 B male fittings and type BS tapped holes 5.1 Type B male fittings Type B male fittings shall meet the requirements of Figure 5 and Table 6. The inner and outer surfaces shall be free from oxidation. The outer surface shall be protected against corrosion and shall withstand the salt spray test accor
26、ding to ISO 9227 for at least 96 h. -,-,- ISO 13486-1:1999(E) ISO 6 Dimensions in millimetres Surface roughness values in micrometres a Depending on manufacturing methods, an undercut is optional. Figure 5 Type B male fitting Table 6 Type B male fitting Dimensions Dimensions in millimetres D1 aD4 b
27、D5D6D7EL1L2L3L9S 0 0 15+ , 6g 0 0 1+ , 0,2 0,2min. 0 0 5+ , nom.tol. 4,754,98M10 16,58,311,513511310 0 22 0 , 66,24M12 1810,313,915511312 0 27 0 , 6,356,59M12 18,110,313,912611312 0 27 0 , a Type B male fittings are not applicable to D1 = 8 mm and 10 mm. b Depending on the thickness of the surface p
28、rotection of the pipe, diameter D4 may be adapted according to the agreement between manufacturer and user. 5.2 Type BS tapped holes Type BS tapped holes shall meet the requirements of Figures 6 and 7, and Table 7. -,-,- ISOISO 13486-1:1999(E) 7 Dimensions in millimetres Surface roughness values in
29、micrometres Figure 6 Type BS 1 tapped hole Key 1Tube seat (see clause 6) Figure 7 Type BS 2 tapped hole -,-,- ISO 13486-1:1999(E) ISO 8 Table 7 Type BS tapped hole Dimensions Dimensions in millimetres D1 a D5 6H D9 04 0 , D10 0,3 D11 + 0,15 + 0,05 L5 b L6 0,2 L7 min. 4,75 M10 1 3,33,8511,59,57,5 6 c
30、M12 1 4,156,411,59,57,5 6,35 M12 1 4,55,36,411,59,57,5 a Tapped holes type BS are not applicable to D1 = 8 mm and 10 mm. b For indication only. c Type BS1 only. 6 Tube seats Tube seats shall meet the requirements of Figure 8 and Table 8. Dimensions in millimetres Surface roughness values in micromet
31、res Figure 8 Tube seat -,-,- ISOISO 13486-1:1999(E) 9 Table 8 Tube seat Dimensions Dimensions in millimetres D1D8D10 0,3 D11 0,05 D12 0,2 D13D14 0,05 L10 0,2 L11 0,1 4,753,2 0,13,85,27,56,257,53,2 6,354,5 0,25,36,69,57,76,484,5 85,5 0,26,87,811,89,27,68,85,5 107,5 0,28,89,713,510,59,5107,5 7 Marking
32、 7.1 Male fittings of types A and B shall be marked in accordance with 7.2 or 7.3. 7.2 Fittings manufactured by forging shall be marked with three dents in accordance with Figure 9 and Table 9. Figure 9 Marking on fittings manufactured by forging Table 9 Marking on fittings manufactured by forging D
33、imensions Dimensions in millimetres D1W 0 0 5+ , H 0 0 2+ , D15 max. D16 min. 4,75107 6 129 6,350,50,3 81410,5 101712,5 -,-,- ISO 13486-1:1999(E) ISO 10 7.3 Fittings manufactured on turning lathes shall be step marked according to Figure 10 and Table 10. Figure 10 Marking on fittings manufactured on
34、 turning lathes Table 10 Marking on fittings manufactured on turning lathes Dimensions Dimensions in millimetres D1D8L4 02 0 , 4,759 6 11 6,350,7 813 1016 8 Identification statement Use the following statement in test reports, catalogues and sales literature when electing to comply with this part of
35、 ISO 13486: “Dimensions and designs for double flare pipes, tapped holes, male fittings and tube seats are in accordance with ISO 13486-1:1999, Road vehicles Hydraulic braking systems Part 1: Double flare pipes, tapped holes, male fittings and tube seats.“ -,-,- ISOISO 13486-1:1999(E) 11 Bibliograph
36、y 1ISO 1302:1992, Technical drawings Method of indicating surface texture. 2ISO 3996:1995, Road vehicles Brake hose assemblies for hydraulic braking systems used with a non- petroleum base hydraulic fluid. 3ISO 6120:1995, Road vehicles Brake hose assemblies for hydraulic braking systems used with petroleum base hydraulic fluid. -,-,- ISO 13486-1:1999(E) ISO ICS 43.040.40 Price based on 11 pages -,-,-