《BS-5276-3-1979.pdf》由会员分享，可在线阅读，更多相关《BS-5276-3-1979.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 5276-3: 1979 Specification for Pressure vessel details (dimensions) Part 3: Dimensional tolerances for ferrous pressure vessels UDC 621.772.4:621.642.3:66.023 Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3:1979
2、 This British Standard, having been prepared under the direction of Pressure Vessel Standards Committee, was published under the authority of the Executive Board and comes into effect on 28 February 1979 BSI 07-1999 First published as DD 42 October 1974 First published as BS 5276-3 February 1979 The
3、 following BSI references relate to the work on this standard: Committee reference PVE/11 Draft for approval DD 42 ISBN 0 580 10662 4 Cooperating organizations The Pressure Vessel Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the foll
4、owing Government department and scientific and industrial organizations: Associated Offices Technical Committee* Association of Shell Boilermakers British Chemical Engineering Contractors Association* British Gas Corporation* British Insurance (Atomic Energy) Committee* British Steel Industry* CBMPE
5、* Chemical Industries Association* Department of Trade (Marine Division) Electricity Supply Industry in England and Wales* Engineering Equipment Users Association* Health and Safety Executive Institution of Chemical Engineers Institution of Gas Engineers* Institution of Mechanical Engineers* Lloyds
6、Register of Shipping* Oil Companies Materials Association* Process Plant Association* United Kingdom Atomic Energy Authority University of Manchester Institute of Science and Technology Water-tube Boilermakers Association Welding Institute The organizations marked with an asterisk in the above list,
7、 together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Association of Consulting Engineers National Association of Drop Forgers and Stampers Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: she
8、ffieldun sheffieldun, na, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3:1979 BSI 07-1999i Contents Page Cooperating organizationsInside front cover Forewordii 1Scope1 2Tangent lines1 3Tolerances1 Figure 1 Vertical pressure vessel3 Figure 2 Horizontal pressure vessel4 Table
9、 1 Tolerance on length (L) between reference planes1 Table 2 Out of level tolerance on base ring1 Table 3 Tolerance on bolt circle diameter1 Table 4 Tolerance on location of welded saddles1 Table 5 Tolerance on level of tray support rings2 Table 6 Tolerance on level of top of weir2 Publications refe
10、rred toInside back cover Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3:1979 ii BSI 07-1999 Foreword This British Standard has been prepared under the direction of the Pressure Vessel Standards Committee to cover the dimensions of
11、 pressure vessel details. It has been arranged in Parts as follows: Part 1: Davits for branch covers; Part 2: Saddle supports for horizontal cylindrical pressure vessels; Part 3: Dimensional tolerances for ferrous pressure vessels; Part 4: Standardized pressure vessels. This Part replaces DD 42 “Rec
12、ommendations for dimensional tolerances for pressure vessels”, which was published in 1974 to obtain experience of the practical application of the recommended dimensional tolerances. The result of this experience is reflected in this present Part. DD 42 is now withdrawn. It is recognized that certa
13、in processes demand vessels having features positioned to tolerances closer than those specified in this Part; in these cases the tolerances are subject to agreement between purchaser and manufacturer. A British Standard does not purport to include all the necessary provisions of a contract. Users o
14、f British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a bac
15、k cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3:1979 BS
16、I 07-19991 1 Scope This Part of BS 5276 specifies dimensional tolerances for ferrous pressure vessels and the non-pressure-containing parts associated with them. The tolerance values specified represent good practice based upon economical manufacture. NOTE 1If wider tolerances are acceptable or clos
17、er tolerances are required these should be agreed between the purchaser and the manufacturer (see foreword). NOTE 2The requirements for aluminium alloy and other non-ferrous vessels are being considered for inclusion at a later date. 2 Tangent lines see Figure 1(a) and Figure 2(a) Tangent lines are
18、taken as reference planes. The vessel axis is taken as the straight line passing through the centre of the reference planes. 3 Tolerances 3.1 Tolerance on length (L) between reference planes see Figure 1(a) and Figure 2(a). The tolerances shall be as detailed in Table 1. Table 1 Tolerance on length
19、(L) between reference planes NOTENo tolerance for lengths over 30 m is specified. This is dependent on an agreement between purchaser and manufacturer. Special consideration may have to be given to the effect of shrinkage due to welding. 3.2 Diameter, circumference, straightness and out-of-roundness
20、. The tolerances on these dimensions shall be as specified in the applicable Design Code, e.g. BS 5500. 3.3 Radial orientation see Figure 1 (c). Tolerance on the radial orientation of downcovers and seal pans measured on the internal surface of the vessel shall be 6 mm. 3.4 Tolerance on supports for
21、 vertical vessels see Figure 1(a). The tolerances shall be as follows: a) distance from underside of support feet to reference plane: + 12 mm, 0; b) distance from underside of base ring to reference plane: + 0, 12 mm. 3.5 Base ring out of level, measured over any diameter see Figure 1 (a). The toler
22、ances shall be as detailed in Table 2. Table 2 Out of level tolerance on base ring 3.6 Bolt circle diameter (for holding down bolts in base plates) see Figure 1(a). The tolerances shall be as detailed in Table 3 and 3.6.1. Table 3 Tolerance on bolt circle diameter 3.6.1 Circumferential position of b
23、olt holes measured on the bolt circle: tolerance shall be 3 mm. 3.7 Saddles (see Figure 2) 3.7.1 For location of welded saddles, a) from saddle centreline to reference plane, b) between saddles, the tolerances shall be as detailed in Table 4. Table 4 Tolerance on location of welded saddles 3.7.2 Tol
24、erance on bolt hole centres in a saddle base plate shall be 3 mm. 3.7.3 Tolerance on the height of welded-on saddles shall be + 0, 6 mm. 3.7.4 Deviation from level of the saddle base plate along its length shall be 3 mm max. 3.7.5 Deviation from level of the saddle base plate across its width shall
25、be 1.5 mm max. 3.8 Nozzle. Tolerances on nozzles shown on vertical vessels (see Figure 1) apply equally to horizontal vessels although they are not all illustrated in Figure 2. LengthTolerance mm Up to and including 2.5 m 6 Over 2.5 m up to and including 5 m 10 Over 5 m up to and including 10 m 13 O
26、ver 10 m up to and including 15 m 16 Over 15 m up to and including 30 m 20 Over 30 msee note Vessel diameterTolerance mm Up to and including 2 m3 Over 2 m5 Vessel diameterTolerance mm Up to and including 2.2 m 3 Over 2.2 m 6 Dimension (a) and (b)Tolerance mm Up to and including 4 m 3 Over 4 m up to
27、and including 7 m 6 Over 7 m up to and including 10 m 9 Over 10 m 13 Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3:1979 2 BSI 07-1999 3.8.1 Tolerance on dimensions locating a nozzle (not manways) to the reference plane shall be 6
28、 mm, with the following exceptions see Figure 1(a) and Figure 2(a): a) tolerance on the dimension from support ring to nozzles related to trays and draw-off pans shall be 3 mm; b) tolerance on locating dimension for nozzles used as reboiler connection shall be 3 mm; c) tolerance on nozzles where dim
29、ensions are marked “MAINTAIN” (see 3.8.6). 3.8.2 Tolerance on the orientation of nozzles and other attachments (not manways) measured by external strapping of the shell shall be 6 mm see Figure 1(b) and Figure 1(c). 3.8.3 Tolerance on the dimension between the flange face of a nozzle and the outside
30、 surface of a shell or reference plane shall be 5 mm see Figure 1(a) and Figure 2(a). 3.8.4 The flange face of a nozzle shall not deviate from parallelism with the indicated plane by more than 1 mm per 100 mm of flange diameter ( ) to a maximum of 6 mm see Figure 1(a). 3.8.5 Maximum rotational displ
31、acement of bolt holes in the bolt circle of nozzle flanges shall not exceed the diametrical clearance in the bolt holes see Figure 1(b). 3.8.6 Where dimensions between nozzles are marked “MAINTAIN” e.g. level gauge connections, the following tolerances shall apply see Figure 1(a) and Figure 1(e): a)
32、 distance between nozzles shall be 1.5 mm; b) difference in vertical alignment shall not exceed 1.5 mm; c) flange faces shall not deviate from the vertical plane by more than 1.5 mm; d) flange faces shall not deviate from parallelism, when compared with a flat surface, by more than 0.5 mm per 100 mm
33、 of flange diameter. 3.9 Manways 3.9.1 Manways shall be positioned within 13 mm of their indicated position see Figure 1(a) and Figure 2(a). 3.9.2 Tolerance on the dimension between the flange face of a manway and the outside surface of the shell shall be 10 mm see Figure 1(a) and Figure 2(a). 3.9.3
34、 The maximum tilt across the flange face of a manway shall not exceed 6 mm see Figure 1(a) and Figure 2(a). 3.10 Tray support rings 3.10.1 Tolerance on the dimension between the first tray support ring and the reference plane shall be 5 mm see Figure 1(a). 3.10.2 Tolerance on distance between adjace
35、nt tray support rings and related parts (height of weirs and orifice openings) shall be 3 mm see Figure 1(a). 3.10.3 The tray support rings across the diameter shall be level within the limits detailed in Table 5 see Figure 1(a). Table 5 Tolerance on level of tray support rings 3.10.4 Welded tray su
36、pport rings shall be at right angles to the shell within a tolerance of 1 mm per 50 mm of support ring width see Figure 1(d). 3.11 Weirs, etc. 3.11.1 Tolerance on weir location to far side of the tower shall be 10 mm see Figure 1(a). 3.11.2 The top of the weir shall be level within the limits detail
37、ed in Table 6 see Figure 1(a). Table 6 Tolerance on level of top of weir Tray diameterDifference between high and low point mm Up to and including 1.2 m3 Over 1.2 m up to and including 2.4 m5 Over 2.4 m6 Vessel diameterDifference between high and low point mm Up to and including 1.2 m3 Over 1.2 m up
38、 to and including 2.4 m5 Over 2.4 m6 Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3:1979 BSI 07-19993 NOTENumbers on the drawing refer to text subclauses. Figure 1 Vertical pressure vessel Licensed Copy: sheffieldun sheffieldun, n
39、a, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3:1979 4 BSI 07-1999 NOTENumbers on the drawing refer to text subclauses. Figure 2 Horizontal pressure vessel Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3
40、:1979 BSI 07-1999 Publications referred to BS 5276, Pressure vessel details (dimensions)1). BS 5276-1, Davits for branch covers. BS 5276-2, Saddle supports for horizontal cylindrical pressure vessels. BS 5276-4, Standardized pressure vessels. BS 5500, Unfired fusion welded pressure vessels. 1) Refer
41、red to in foreword only. Licensed Copy: sheffieldun sheffieldun, na, Fri Dec 01 14:29:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5276-3: 1979 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standa
42、rds. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the consta
43、nt aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:
44、 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Custom
45、er Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informat
46、ion on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996
47、 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in a
48、ll BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means el
49、ectronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payme