《ISO-15612-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-15612-2004.pdf(14页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 15612:2004(E) ISO 2004 INTERNATIONAL STANDARD ISO 15612 First edition 2004-08-01 Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure Descriptif et qualification dun mode opratoire de soudage pour
2、 les matriaux mtalliques Qualification par rfrence un mode opratoire de soudage standard Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:14:48 MDTNo reproduction or networking
3、 permitted without license from IHS -,-,- ISO 15612:2004(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the
4、 computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to
5、 create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please infor
6、m the Central Secretariat at the address given below. ISO 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from ei
7、ther ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2004 All rights reserved Copyright Internatio
8、nal Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:14:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15612:2004(E) ISO 2004 All rights reserved iii Foreword ISO (th
9、e International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committ
10、ee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechn
11、ical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member
12、bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying
13、any or all such patent rights. ISO 15612 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the Agreement
14、 on technical cooperation between ISO and CEN (Vienna Agreement). This first edition of ISO 15612 cancels and replaces ISO 9956-7:1995, of which it constitutes a technical revision. Throughout the text of this document, read “.this European Standard.” to mean “.this International Standard.”. Annex Z
15、A provides a list of corresponding International and European Standards for which equivalents are not given in the text. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:14:48
16、MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15612:2004(E) iv ISO 2004 All rights reserved Contents Page Forewordv Introductionvi 1 Scope 1 2 Normative references 1 3 Terms and definitions .2 4 Preliminary welding procedure specification (pWPS) .2 5 Qualification by
17、adoption of the standard welding procedure .2 5.1 General2 5.2 Parent metal .2 6 Use of a standard welding procedure .3 6.1 General3 6.2 Related to the user of a standard welding procedure3 6.3 Related to the welding equipment .3 6.4 Related to the personnel.3 7 Validity 4 8 Preparation and document
18、ation.4 Annex ZA (normative) Normative references to international publications with their relevant European publications5 Bibliography6 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/2
19、1/2007 11:14:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15612:2004(E) ISO 2004 All rights reserved v Foreword This document (EN ISO 15612:2004) has been prepared by Technical Committee CEN/TC 121 “Welding”, the secretariat of which is held by DIN, in collaborati
20、on with Technical Committee ISO/TC 44 “Welding and allied processes”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2005, and conflicting national standards shall be withdrawn at the la
21、test by February 2005. This document supersedes EN 288-7:1995. Normative references to International Standards are listed in annex ZA. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Aus
22、tria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Copyright International Organiz
23、ation for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:14:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15612:2004(E) vi ISO 2004 All rights reserved Introduction In EN ISO 15607
24、, one of the methods of welding procedure qualification is by adoption of a standard welding procedure. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:14:48 MDTNo reproductio
25、n or networking permitted without license from IHS -,-,- ISO 15612:2004(E) ISO 2004 All rights reserved 1 1 Scope This standard gives the necessary information to explain the requirements referenced in EN ISO 15607 about the qualification by adoption of a standard welding procedure, and establishes
26、the conditions, limits and ranges of qualification necessary for the use of a standard welding procedure. This standard gives the manufacturer the possibility to use welding procedures based on welding procedure tests performed by other organisations. This standard is a part of a series of standards
27、, details of this series are given in EN ISO 15607:2003, annex A. The use of this standard can be restricted by an application standard or a specification. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the
28、 edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 287-1,Qualification test of welders - Fusion welding - Part 1: Steels. EN 287-2, Approval testing of welders Fusion welding Part 2 : Aluminium and aluminium alloys. EN
29、 719, Welding coordination Tasks and responsibilities. EN 729-1, Quality requirements for welding Fusion welding of metallic materials Part 1: Guidelines for selection and use. EN 729-2, Quality requirements for welding Fusion welding of metallic materials Part 2: Comprehensive quality requirements.
30、 EN 729-3, Quality requirements for welding Fusion welding of metallic materials Part 3: Standard quality requirements. EN 729-4, Quality requirements for welding Fusion welding of metallic materials Part 4: Elementary quality requirements. EN 1418, Welding personnel Approval testing of welding oper
31、ators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials. EN ISO 9606-3, Approval testing of welders Fusion welding Part 3: Copper and copper alloys (ISO 9606-3:1999) EN ISO 9606-4, Approval testing of welders Fusion welding Part 4: Nickel
32、 and nickel alloys. (ISO 9606-4:1999) EN ISO 9606-5, Approval testing of welders Fusion welding Part 5: Titanium and titanium alloys, zirconium and zirconium alloys (ISO 9606-5:2000) EN ISO 15607:2003, Specification and qualification of welding procedures for metallic materials General rules. (ISO 1
33、5607:2003) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:14:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15612:2004(E) 2 ISO 2004 All rig
34、hts reserved EN ISO 15609-1, Specification and approval of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding. (ISO 15609-1:2004) EN ISO 15609-2, Specification and qualification of welding procedures for metallic materials Welding procedure specification Pa
35、rt 2: Gas welding. (ISO 15609-2:2001) EN ISO 15609-3, Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 3: Electron beam welding. (ISO 15609-3:2004) EN ISO 15609-4, Specification and qualification of welding procedures for metallic mate
36、rials Welding procedure specification Part 4: Laser beam welding. (ISO 15609-4:2004) EN ISO 15614 (all parts), Specification and qualification of welding procedures for metallic materials Welding procedure test. 3 Terms and definitions For the purposes of this European Standard, the terms and defini
37、tions given in EN ISO 15607:2003 apply. 4 Preliminary welding procedure specification (pWPS) The qualification by adoption of a standard welding procedure shall be based on a pWPS according to the appropriate part of EN ISO 15609. This pWPS shall specify the range for all the relevant parameters. 5
38、Qualification by adoption of the standard welding procedure 5.1 General The qualification of the welding procedure shall be carried out by an examiner or an examiner body according to EN ISO 15607. It shall be verified that examination and testing have been carried out in accordance with the appropr
39、iate part of EN ISO 15614. After qualification, the preliminary welding procedure specification will be considered as a standard welding procedure specification. Changes outside the range of qualification given in the appropriate part of EN ISO 15614 as modified in 5.2 shall require a new qualificat
40、ion welding procedure. The welding procedure shall be qualified by the manufacturer and if applicable, verified by an examiner or examining body in accordance with EN ISO 15607. 5.2 Parent metal This standard is applicable for parent material groups defined in Table 1. Copyright International Organi
41、zation for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:14:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15612:2004(E) ISO 2004 All rights reserved 3 Table 1 Applicable parent ma
42、terial groups Parent material groups used for the qualification of the welding procedure Range of qualification 1-1 1-1 1- 11 1 - 1 1 - 11 11 11 8 a 8 8 21 21 21 22.1 - 22.2 22.1 - 22.1 22.2 - 22.2 22.1 - 22.2 31 through 38 a each group welded with compatible filler material 41 through 47 a each gro
43、up welded with compatible filler material a excluding those alloys which are extremely sensitive to hot cracking. 6 Use of a standard welding procedure 6.1 General A standard welding procedure prepared and documented in accordance with clause 8 can be used without further tests providing the followi
44、ng requirements and limitations are observed. 6.2 Related to the user of a standard welding procedure The user of a standard welding procedure is responsible for the appropriate selection and application of the standard welding procedure. The use of a standard welding procedure requires welding coor
45、dination in accordance with EN 719 and that the user fulfils quality requirements in accordance with the appropriate part of EN 729. 6.3 Related to the welding equipment The standard welding procedure is qualified for use in production with welding power sources and welding equipment having electric
46、al and mechanical characteristics which are capable of achieving those used in preparing the test weld for qualification of the standard welding procedure as specified in the welding procedure specification WPS. The equipment used during production shall permit control of all essential welding param
47、eters. 6.4 Related to the personnel A standard welding procedure shall only be used by welders or welding operators for mechanized equipment qualified in accordance with the relevant part of EN 287 or EN ISO 9606 or EN 1418. Copyright International Organization for Standardization Provided by IHS un
48、der license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 11:14:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15612:2004(E) 4 ISO 2004 All rights reserved 7 Validity A standard welding procedure remains valid until it is withdrawn or revised. 8 Preparation and documentation The standard welding procedure s