《ISO-17030-2003.pdf》由会员分享，可在线阅读，更多相关《ISO-17030-2003.pdf（10页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO/IEC 17030:2003(E) ISO 2003 INTERNATIONAL STANDARD ISO/IEC 17030 First edition 2003-10-01 Conformity assessment General requirements for third-party marks of conformity valuation de la conformit Exigences gnrales pour les marques de conformit par tierce partie ISO/IEC 17030:2003
2、(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this fi
3、le, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info r
4、elative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. IS
5、O 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the
6、 country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reserved ISO/IEC 17030:2003(E) ISO 2003 All rights reserved iii Foreword ISO (the Int
7、ernational Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees establ
8、ished by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the
9、field of conformity assessment, the ISO Committee on conformity assessment (CASCO) is responsible for the development of International Standards and Guides. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. Draft International Standards are cir
10、culated to the national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held re
11、sponsible for identifying any or all such patent rights. ISO/IEC 17030 was prepared by the ISO Committee on conformity assessment (CASCO). It was circulated for voting to the national bodies of both ISO and IEC, and was approved by both organizations. ISO/IEC 17030:2003(E) iv ISO 2003 All rights res
12、erved Introduction Marks of conformity take many forms and different uses. They can convey useful information about a product, or indicate particular characteristics of a product such as its safety, quality, performance, reliability or impact on the environment. They are found on products, certifica
13、tes and publications denoting the conformity to specified requirements of a product, management system, service, process, person or an organization. Most important for all marks of conformity is to gain the confidence of the market, including consumers, in products and other objects of conformity as
14、sessment to which these marks have been applied. The prime purpose of this International Standard is to enable a uniform approach to the use of third-party marks of conformity, to fill relevant gaps in existing ISO, IEC, ISO/IEC Standards and Guides, to address potential problems arising from differ
15、ent uses of third-party marks of conformity, to provide a clear and rational basis for their use, and to set out general requirements. This International Standard concentrates on third- party marks of conformity but may also be used as guidance for other applications of marks of conformity. This Int
16、ernational Standard is based on market feedback and demands from various users and issuers of marks of conformity assessment. It takes account of the ISO report on Marks of conformity assessment, published in May 1999. The use of this International Standard should lead to improved market confidence,
17、 international recognition and consumer acceptance of third-party marks of conformity. INTERNATIONAL STANDARD ISO/IEC 17030:2003(E) ISO 2003 All rights reserved 1 Conformity assessment General requirements for third-party marks of conformity 1 Scope This International Standard provides general requi
18、rements for third-party marks of conformity, including their issue and use. NOTE This International Standard can also be used as guidance in using marks of conformity in other than third- party conformity assessment activity. 2 Normative references The following referenced documents are indispensabl
19、e for the application of this document. For dated references, only the edition cited apply. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 17000, Conformity assessment General vocabulary1) 3 Terms and definitions For the purposes of
20、this document, the terms and definitions given in ISO/IEC 17000 and the following apply. 3.1 third-party mark of conformity protected mark issued by a body performing third-party conformity assessment, indicating that an object of conformity assessment (product, process, person, system or body) is i
21、n conformity with specified requirements EXAMPLES Third-party marks of conformity can be: product certification marks, quality/environment management system certification marks, environmental conformity marks, etc. NOTE 1 A protected mark is a mark legally protected against unauthorized use. NOTE 2
22、The specified requirements are generally stated in “normative” documents such as International Standards, regional or national standards, regulations and specifications. 3.2 owner of a third-party mark of conformity person or organization that has legal rights to a third-party mark of conformity 1)
23、To be published. ISO/IEC 17030:2003(E) 2 ISO 2003 All rights reserved 3.3 issuer of a third-party mark of conformity body that grants the right to use a third-party mark of conformity NOTE The issuer may not be the owner of the third-party mark of conformity, and may be authorized to sub-licence oth
24、er bodies. 4 General requirements 4.1 The owner of a third-party mark of conformity shall be responsible for protecting the mark legally against unauthorized use. 4.2 The owner and/or issuer of the third-party mark of conformity shall a) have rules governing the use of the third-party mark of confor
25、mity, b) take measures to minimize misunderstandings and lack of clarity regarding the third-party mark of conformity that could lead to a reduction in its effectiveness, c) have rules to ensure that the third-party mark of conformity and any accompanying information are not misleading and take acti
26、on against their use in a misleading way, d) have measures to protect and monitor the use of the third-party mark of conformity, e) take actions to resolve misuses of the third-party mark of conformity, including withdrawal of the mark or appropriate legal action, and f) take action on and keep a re
27、cord of all complaints relating to the use of the third-party mark of conformity. 4.3 When the owner or issuer of the third-party mark of conformity grants a licence for the use of that mark by others, a binding agreement shall be made according to the rules referred to in 4.2 a). 5 Design and appli
28、cation of third-party marks of conformity 5.1 The design of the third-party mark of conformity, or accompanying or publicly available information, shall identify the issuer and the aspects covered by the mark (e.g. safety, environmental, performance, ethics) in a way that avoids any potential misund
29、erstanding. A third-party mark of conformity should be so designed as to minimize the risk of counterfeiting or other forms of misuse. 5.2 A third-party mark of conformity may be accompanied by additional information to make the meaning of the mark more clearly understood. Such information shall not
30、 be misleading and should be in a language understood by the intended recipients. NOTE It is preferable to use symbols that are universally understandable rather than descriptive words. 5.3 A third-party mark of conformity shall be traceable back to the specified requirements to which the object of
31、conformity assessment conforms. 5.4 Only a third-party mark of conformity issued in accordance with product conformity assessment may be displayed on the product or product packaging. All other third-party marks of conformity, such as those relating to quality or environmental management systems and
32、 services, shall not be displayed on a product, product packaging, or in a way that may be interpreted as denoting product conformity. -,-,- ISO/IEC 17030:2003(E) ISO 2003 All rights reserved 3 5.5 When a third-party mark of conformity relates to a tangible product, the mark shall be directly applie
33、d to each product, except where the physical size of the product does not permit this or when the application is not appropriate for the type of product, in which case it may be applied on the package or other accompanying information. If a third-party mark of conformity only relates to certain part
34、s of a product, the rules governing its use shall include requirements to minimize any misunderstanding that the mark applies to the entire product. 5.6 A reference to third-party marks of conformity may also be used on documents, promotional material, etc. 6 Issuing third-party marks of conformity
35、6.1 Issuing of the third-party mark of conformity shall be based on a conformity assessment system or scheme that contains at least the following elements: a) determination of characteristics of the object of conformity assessment, consisting of, as appropriate, testing, examination of persons, asse
36、ssment of bodies, auditing of management systems, etc.; b) review, i.e. examination of the extent to which an object of conformity assessment fulfils specified requirements; c) a decision following review that an object of conformity assessment fulfils specified requirements; d) licensing, or other
37、methods, giving authorization to others to use the third-party mark of conformity unless covered by 6.2; e) surveillance, evaluating the continued conformity of the object of conformity assessment to specified requirements sufficient to assure continued confidence in the third-party mark of conformi
38、ty unless covered by 6.2. 6.2 In conformity assessment systems or schemes for which the issuer evaluates each object of conformity assessment produced prior to the application of the third-party mark of conformity, licensing and surveillance are not required. 6.3 The third-party mark of conformity s
39、hall only be applied under the rules laid down in a publicly available conformity assessment system or scheme. 6.4 An appropriate maximum period of time for applying a third-party mark of conformity after the specified standard or other normative document is revised or becomes obsolete shall be esta
40、blished by the rules of the conformity assessment system or scheme. 7 Ownership and control 7.1 Information 7.1.1 The owner or issuer shall provide, on request, information that explains the meaning of the third-party mark of conformity. Specific responses to questions or concerns from interested pa
41、rties regarding the third- party mark of conformity shall be provided. 7.1.2 The owner or issuer shall maintain and update a list of objects of conformity assessment which have been granted the third-party mark of conformity and that list shall be available on request.2) 2) This requirement is simil
42、ar in meaning to those in ISO/IEC Guide 61:1996, 2.1.7.1 g); ISO/IEC Guide 62:1996, 2.1.7.1 g) and ISO/IEC Guide 65:1996, 4.8.1 g). ISO/IEC 17030:2003(E) 4 ISO 2003 All rights reserved 7.1.3 The owner or issuer of the third-party mark of conformity shall maintain, update and make available on reques
43、t, a description of the rights and obligations of licensees, and other restrictions or limitations on the use of the mark. 7.2 Licence 7.2.1 The binding agreement specified in 4.3 shall contain provisions to assure that the licensee follows the rules of the system or scheme. 7.2.2 A licence shall re
44、quire the licensee a) to control the use of the third-party mark of conformity, b) to take corrective actions in case of non-conformity, and c) to keep a record of all complaints relating to the use of the third-party mark of conformity and make these available to the owner/issuer. 7.3 Monitoring th
45、e use of third-party marks of conformity 7.3.1 The owner or issuer shall establish a procedure to deal with any alleged incorrect or misleading uses of the third-party mark of conformity and shall take suitable actions. NOTE Suitable actions can include periodical surveillance of licensees, correcti
46、ve action, withdrawal of licence, publication of the transgression and, if necessary, other legal action. This subclause also applies in situations of misuse by a party not under contract with the owner of the third-party mark of conformity. 7.3.2 A corrective action plan shall be established in res
47、pect of each misuse of the third-party mark of conformity. The corrective action plan should include steps to cooperate with other interests as far as possible, depending on the extent to which their involvement will minimize the negative consequence of the misuse. NOTE Each corrective action plan c
48、an be different since the situation surrounding each misuse of the third-party mark of conformity will vary. -,-,- ISO/IEC 17030:2003(E) ISO 2003 All rights reserved 5 Bibliography 1 ISO/IEC Guide 61:1996, General requirements for assessment and accreditation of certification/registration bodies 2 I
49、SO/IEC Guide 62:1996, General requirements for bodies operating assessment and certification/- registration of quality systems 3 ISO/IEC Guide 65:1996, General requirements for bodies operating product certification systems 4 ISO/IEC Guide 66:1999, General requirements for bodies operating assessment and certification/- registration of environmental management systems (EMS) 5 ISO 14024:1999, Environmental labels and declarations Type I environment