《ISO-2584-1972.pdf》由会员分享,可在线阅读,更多相关《ISO-2584-1972.pdf(3页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD INTERNATIONAL ORGANIZATION FOR STANDARDlZATlON .MEXYHAPOflHAR OPTAHM3ALMI “0 CTAHhWTM3A”MM .ORGANISAT,ON ,NTERNAT,ONALE DE NORMALISATION Cylindrical cutters with plain bore and key drive - Metric series First edition - 1972- 12-01 UDC 621.914.28 Descripteurs : tools, cutting t
2、ools, milling cutters, dimensions. Ref. No. IS0 2584-1972 (E) Price based on 1 page Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 09:53:04 MDTNo reproduction or networking perm
3、itted without license from IHS -,-,- FOREWORD IS0 (the International Organization for Standardization) is a worldwide federation of national standards institutes (IS0 Member Bodies). The work of developing International Standards is carried out through IS0 Technical Committees. Every Member Body int
4、erested in a subject for which a Technical Committee has been set up has the right to be represented on that Committee. International organizations, governmental and nongovernmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the Technical Committees ar
5、e circulated to the Member Bodies for approval before their acceptance as International Standards by the IS0 Council. International Standard IS0 2584 was drawn up by Technical Committee ISO/TC 29, Small tools. It was approved in February 1972 by the Member Bodies of the following countries : Austria
6、 Italy Belgium Japan Egypt, Arab Rep. of Netherlands France Poland Hungary Romania India South Africa, Rep. of Israel Spain Sweden Switzerland Thailand Turkey United Kingdom U.S.A. U.S.S.R. The Member Body of the following country expressed disapproval of the document on technical grounds : Czechosl
7、ovakia 0 International Organization for Standardization, 1972 l Printed in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 09:53:04 MDTNo reproduction or networking p
8、ermitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 2584-1972 (E) Cylindrical cutters with plain bore and key drive - Metric series 1 SCOPE AND FIELD OF APPLICATION This International Standard specifies the dimensions of metric series cylindrical cutters with plain bore and key drive,
9、 intended for fitting to cutter arbors. It is applicable to solid cutters and also to interlocking cutters. Solid cutters are made either with straight teeth or with helicoidal teeth angled to the right or left; interlocking cutters are always made with straight or helicoidal teeth angled to the lef
10、t and right alternately. The range of outside diameters of these cutters is taken from ISO/R 523, Recommended range of outside diameters for milling cutters. 2 REFERENCE ISOIR 240, Interchangeability dimensions for milling cutters and cutter arbors or cutter mandrels - Metric series and inch series.
11、 3 DIMENSIONS 3.1 Solid cutters FIGURE 1 -Solid cutter FIGURE 2 - Interlocking cutter TABLE 1 3.2 Interlocking cutters TABLE 2 Dimensions in millimetres Dimensions in millimetres D d“ L is16 H7 80 100 125 160 200 1 250 80 32 X X 100 40 X X 125 50 X X -. 160 60 X X l The bore and keyway dimensions sh
12、all be in accordance with the metric series of ISO/R 240. 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 09:53:04 MDTNo reproduction or networking permitted without license from IHS -,-,-