《ISO-2320-2008.pdf》由会员分享，可在线阅读，更多相关《ISO-2320-2008.pdf（24页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 2320:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 2320 Fourth edition 2008-11-01 Prevailing torque type steel nuts Mechanical and performance properties crous autofreins en acier Caractristiques mcaniques et performances Copyright International Organization for Standardization P
2、rovided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 22:36:05 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 2320:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy,
3、this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secr
4、etariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to en
5、sure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publicat
6、ion may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 2
7、0 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 22:
8、36:05 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 2320:2008(E) ISO 2008 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 2 4 Symbols. 2 5 Thread 3 6 Lubrication 3 7 Mechanical properties of prevailing t
9、orque type nuts 3 8 Performance requirements for prevailing torque properties. 3 9 Test method. 12 9.1 General. 12 9.2 Proof load test. 12 9.3 Prevailing torque test. 12 Annex A (normative) Temperature resistance of prevailing torque non-metallic insert type nuts. 17 Annex B (informative) Basis for
10、the evaluation of the total coefficient of friction, tot. 18 Bibliography. 19 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 22:36:05 MSTNo reproduction or networking permitted without license f
11、rom IHS -,-,- ISO 2320:2008(E) iv ISO 2008 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical com
12、mittees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
13、 International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Internatio
14、nal Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be t
15、he subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2320 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 1, Mechanical properties of fasteners. This fourth edition cancels and replaces the third edition (ISO 2320:
16、1997), which has been technically revised. It also incorporates the Technical Corrigendum ISO 2320:1997/Cor.1:2006. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 22:36:05 MSTNo reproduction or
17、networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 2320:2008(E) ISO 2008 All rights reserved 1 Prevailing torque type steel nuts Mechanical and performance properties 1 Scope This International Standard specifies the mechanical and performance properties for prevailing to
18、rque type steel nuts when tested at an ambient temperature range of +10 C to +35 C. It includes a single test to determine the prevailing torque properties (performance properties) and/or the torque/clamp force properties. This International Standard applies to prevailing torque all metal type nuts
19、and prevailing torque non-metallic insert type nuts: a) with triangular ISO thread according to ISO 68-1; b) with diameter/pitch combination according to ISO 261 and ISO 262; c) with coarse pitch thread M3 to M39 and mechanical properties according to ISO 898-2; d) with fine pitch thread M81 to M393
20、 and mechanical properties according to ISO 898-6; e) within the temperature range of 50 C to +150 C for prevailing torque all metal type nuts; NOTE 1 See Clause 7, paragraph 3. f) within the temperature range of 50 C to +120 C for prevailing torque non-metallic insert type nuts. NOTE 2 See Clause 7
21、, paragraph 4. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 273:197
22、9, Fasteners Clearance holes for bolts and screws ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs ISO 898-2, Mechanical properties of fasteners Part 2: Nuts with specified proof load values Coarse thread ISO 898-6, Mechanical propert
23、ies of fasteners Part 6: Nuts with specified proof load values Fine pitch thread ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality ISO 16047, Fasteners Torque/clamp force testing Copyright Int
24、ernational Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 22:36:05 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 2320:2008(E) 2 ISO 2008 All rights reserved 3 Terms and definitions For t
25、he purposes of this document, the terms and definitions given in ISO 16047 and the following apply. 3.1 prevailing torque type nut nut which is not free-running on a mating thread by virtue of a self-contained prevailing torque feature, and which provides a degree of resistance to rotation independe
26、nt of clamping or compression forces 3.2 prevailing torque developed by the nut torque necessary to rotate the nut on its mating externally threaded component and with no axial force in the mating component 3.3 prevailing-on torque torque to rotate the nut on its mating externally threaded component
27、 with the torque measured while the nut is in motion and with no clamp force 3.4 prevailing-off torque torque to rotate after backing off the nut until the removal of the clamp force in the externally threaded component in the following 360 rotation of the nut 3.5 prevailing torque all metal type nu
28、t nut which has a one piece or a multiple piece metal construction and derives its prevailing torque characteristics from a controlled distortion of the nut thread and/or body or from metallic insert(s) 3.6 prevailing torque non-metallic insert type nut nut which has a multiple piece construction an
29、d derives its prevailing torque characteristics from insert(s) of non-metallic material located and retained in the nut 3.7 seating point point in the tightening process where clamp force first appears 4 Symbols For the purpose of this International Standard, the following symbols apply together wit
30、h those defined in ISO 16047. Symbol Designation d nominal diameter d4 diameter of the hole of the fixture FP proof load F65 lower load limit for the evaluation of the coefficient of total friction at 65 % of FP F75 upper load limit for the evaluation of the coefficient of total friction at 75 % of
31、FP F80 test clamp force (shut-down force for the tightening process) at 80 % of FP P pitch of the thread TFv prevailing-on torque, in newton metres Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009
32、 22:36:05 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 2320:2008(E) ISO 2008 All rights reserved 3 TFd prevailing-off torque, in newton metres T65 lower torque limit for the evaluation of the coefficient of total friction at F65 T75 upper torque limit for the evaluat
33、ion of the coefficient of total friction at F75 T80 test torque corresponding to 80 % of the proof load, in newton metres (see Tables 1 to 8) tot coefficient of total friction 5 Thread Threads for prevailing torque type nuts shall be in accordance with ISO 965-2 except for the prevailing torque feat
34、ure: a) for prevailing torque non-metallic insert type nuts, the GO gauge shall be suitable for free installation (by hand) until it is seated against the prevailing torque feature; b) for prevailing torque all metal type nuts, the GO gauge shall be suitable for free installation (by hand) to one pi
35、tch at least. 6 Lubrication At the option of the manufacturer a lubricant may be applied to the manufacturing lot to fulfil the performance requirements. 7 Mechanical properties of prevailing torque type nuts The mechanical properties of prevailing torque type nuts shall conform to ISO 898-2 or ISO
36、898-6. With regard to proof load, the test method specified in 9.2 shall apply. For prevailing torque all metal type nuts, users should consult an experienced fastener materials expert for temperatures outside the range of 50 C to +150 C to determine appropriate choices for a given application. For
37、prevailing torque non-metallic insert type nuts, use at or near the temperature limits of 50 C and +120 C may reduce the prevailing torque capability and may require the use of an adequate non-metallic material. Users should consult an experienced fastener materials expert for temperatures outside t
38、he range of 50 C to +120 C to determine appropriate choices for a given application. 8 Performance requirements for prevailing torque properties The prevailing-on torque shall not exceed the value specified for the applicable nut in Tables 1 to 8. The prevailing-off torque shall exceed the value spe
39、cified for the applicable nut in Tables 1 to 8. For delivery inspection, the 1st installation/removal test applies, unless otherwise agreed. For initial type testing and in case of dispute, a 5th removal test shall also be applied unless otherwise agreed. Prevailing torque performance decreases as a
40、 function of the number of reuses; the consumer should take into consideration the consequences of the decreased performance before any reuse of the nut. By request of the customer, a temperature resistance test for prevailing torque non-metallic insert type nuts as given in Annex A may be carried o
41、ut. Paragraphs 3 and 4 of Clause 7 also apply to performance requirements. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 22:36:05 MSTNo reproduction or networking permitted without license from
42、 IHS -,-,- ISO 2320:2008(E) 4 ISO 2008 All rights reserved Table 1 Test clamp force and prevailing torques for prevailing torque type nuts of property class 04 Clamp force for evaluation of total friction coefficient tot b Prevailing torque Nm Thread d P Test clamp force F80a N Upper limit F75c N Lo
43、wer limit F65d N 1st installation TFv,maxe 1st removal TFd,minf 5th removal TFd,minf M3 1 528 1 433 1 242 0,43 0,12 0,08 M4 2 672 2 505 2 171 0,9 0,18 0,12 M5 4 320 4 050 3 510 1,6 0,29 0,2 M6 6 112 5 730 4 966 3 0,45 0,3 M7 8 800 8 250 7 150 4,5 0,65 0,45 M8 11 120 10 425 9 035 M81 11 920 11 175 9
44、685 6 0,85 0,6 M10 17 600 16 500 14 300 M101,25 18 640 17 475 15 145 M101 19 600 18 375 15 925 10,5 1,5 1 M12 25 600 24 000 20 800 M121,5 26 800 25 125 21 775 M121,25 28 000 26 250 22 750 15,5 2,3 1,6 M14 34 960 32 775 28 405 M141,5 38 000 35 625 30 875 24 3,3 2,3 M16 47 760 44 775 38 805 M161,5 50
45、800 47 625 41 275 32 4,5 3 M18 58 400 54 750 47 450 M181,5 65 360 61 275 53 105 42 6 4,2 M20 74 480 69 825 60 515 M201,5 82 720 77 550 67 210 54 7,5 5,3 M22 92 080 86 325 74 815 M221,5 101 200 94 875 82 225 68 9,5 6,5 M24 107 280 100 575 87 165 M242 116 720 109 425 94 835 80 11,5 8 M27 139 520 130 8
46、00 113 360 M272 150 800 141 375 122 525 94 13,5 10 M30 170 560 159 900 138 580 M302 188 800 177 000 153 400 108 16 12 M33 210 960 197 775 171 405 M332 231 360 216 900 187 980 122 18 14 M36 248 400 232 875 201 825 M363 262 960 246 525 213 655 136 21 16 M39 296 720 278 175 241 085 M393 313 120 293 550
47、 254 410 150 23 18 NOTE The evaluation of results from the prevailing torque test by statistical process control methods (SPC) has no statistical relevance. a The clamp force for property class 04 nuts is equal to 80 % of the proof load of property class 04 nuts for 3 mm u d u 39 mm. Proof loads for
48、 nuts are given in ISO 898-2 and ISO 898-6. b See Annex B. c The value of the upper limit of the clamp force is equal to 75 % of the proof load, see Annex B. d The value of the lower limit of the clamp force is equal to 65 % of the proof load, see Annex B. e The prevailing torques for first assembly apply for all metal type nuts only. For prevailing torque non-metallic insert type nuts, the maximum torques shall be 50 % of the values. f Values in this table are required for te