《ISO-13565-1-1996.pdf》由会员分享，可在线阅读，更多相关《ISO-13565-1-1996.pdf（10页珍藏版）》请在三一文库上搜索。
1、 STD.ISO 135b5-L-ENGL L77b Y851703 07538qL 8 4 T INTERNATIONAL STANDARD IS0 13565-1 :1996 TECHNICAL CORRIGENDUM 1 Published 1998-06-1 5 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION MEWWMAFOIIHAR OPrAHH3AUHR il0 CTAHWPM3AUHH ORGANISATION INTERNATIONALE DE NORMALISATION Geometrical Product Specifica
2、tions (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 1: Filtering and general measurement conditions TECHNICAL CORRIGENDUM 1 Spcification gomtrique des produits (GPS) - Etat de surface: Mthode du profil; surfaces ayant des proprits fonctionnelles dif
3、frentes suivant les niveaux - Partie 1: Filtrage et conditions gnrales de mesurage RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to International Standard IS0 13565-1 :1996 was prepared by Technical Committee ISO/TC 21 3, Dimensional and geometrical product specifications and verification. This m
4、aterial is reproduced from IS0 documentc under International Organization for Standardization (ISO) Copyright License Number IHS/ICC/l996. Not for resale. No part of these IS0 documentc may be reproduced in any form, electronic retrieval system or otherwise, except as allowed in the copyright law of
5、 the country of use, or with the prior written consent of IS0 (Case postale 56, 121 1 Geneva 20, Switzerland, Fax +41 22 734 10 79), IHS or the 150 Licensors members. Page 1 Clause 2 Replace “IS0 4287:1996“ with IS0 4287:1997“. Page 4 Figure A.l Replace “Datum planes“ with “Datums“. ICs 17.040.20 Re
6、f. No. IS0 13565-1 :1996/Cor.l:1998(E) Descriptors: surface properties, surface condition. determination, characteristics, texture profiles, roughness measurement, general conditions. geometrical product specifications. 8 IS01998 Printed in Switzerland 1 NTE RNATI ON AL STANDARD IS0 13565-1 First ed
7、ition 1996-1 2-01 Geometrical Product Specifications (GPS) - Surface texture: Profile method; Surf aces having stratified f u nct i o na I properties - Part 1: Filtering and general measurement conditions Spcification gomtrique des produits (GPSI - tat de surface: Mthode du profil; surfaces ayant de
8、s proprits fonctionnelles diffrentes suivant les niveaux - Partie 7: Filtrage et conditions gnrales de mesurage This material is reproduced from IS0 documents unaer international Organization for Standardization (EO) Copyright License number IHSIICCI1996. Not for resale. No part of these IS0 documen
9、ts may be reproduced in any form, electronic retrieval system or otherwise, except as allowed in the copyright law of the country of use, or with the prior written consent of IS0 (Case postale 56, I211 Geneva 20, Switzerland, Fax +41 22 734 10 79), IHS or the IS0 Licensors members. . Reference numbe
10、r IS0 13565:1996(!3 STD-IS0 335b5-3-ENGL 1796 4853903 0733872 810 IS0 13565:1996(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out thro
11、ugh IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collabor
12、ates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at
13、 least 75 % of the member bodies casting a vote. International Standard IS0 13565-1 was prepared jointly by Technical Committees ISOTTC 57, Metrology and properties of surfaces, Sub- committee SC 1, Geometrical parameters - Instruments and procedures for measurement of surface roughness and waviness
14、, ISOflC 3, Limits and fits, and ISO/TC 1 O, Technical drawings, product definition and related documentation, Subcommittee SC 5, Dimensioning and tolerancing. IS0 13565 consists of the following parts, under the general title Geo- metrical product specifications (GPS) - Surface texture: Profile met
15、hod; Surfaces having stratified functional properties: - Part I: Filtering and general measurement conditions - Part 2: Height characterization using the linear material ratio curve - Part 3: Height characterization using the material probability curve Annexes A and B of this part of IS0 13565 are f
16、or information only. O IS0 1996 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. international Orga
17、nization for Standardization Case Postale 56 CH-1 21 1 Genve 20 Switzerland Printed in Switzerland II -,-,- STD*ISO 335bS-L-ENGL 399b H 4853903 0733873 757 W Q IS0 IS0 13565-1:1996(E) Introduction This part of IS0 13565 is a Geometrical Product Specification (GPS) standard and is to be regarded as a
18、 General GPS standard (see ISO/TR 14638). It influences chain links 2 and 3 of the chain of standards for roughness profile. For more detailed information of the relation of this standard to other standards and the GPS matrix model, see annex A. The roughness profile generated using the filter defin
19、ed in IS0 11562 suffers some undesirable distortions, when the measured surface consists of relatively deep valleys beneath a more finely finished plateau with minimal waviness. This type of surface is very common, for example in cylinder liners for internal combustion engines. This part of IS0 1356
20、5 provides a method of greatly reducing these distortions, thus enabling the parameters defined in IS0 13565-2 and IS0 13565-3 to be used for evaluating the above mentioned type of surface, with minimal influence from these distortions. . 111 STD-IS0 135b5-1-ENGL 177b E i851703 071387q b73 INTERNATI
21、ONAL STANDARD O IS0 IS0 13565-1:1996(E) Geometrical Product Specification (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 1: Filtering and general measurement conditions 1 Scope This part of IS0 13565 describes a filtering method for use with surfaces
22、 that have deep valleys below a more finely finished plateau with a relatively small amount of waviness. The reference line resulting from filtering according to IS0 11562 for such surfaces is undesirably influenced by the presence of the valleys. The filtering approach described in this standard su
23、ppresses the valley influence on the reference line such that a more satisfactory reference line is generated. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 13565. At the time of publication, the edi
24、tions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 13565 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently val
25、id International Standards. IS0 3274:1996, Geometrical Product Specifications IGPSI - Surface texture: Profile method - Nominal characteristics of con tact (stylus) instruments. IS0 4287: 1996, Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surfac
26、e texture parameters. IS0 1 1562:1996, Geometrical Product Specifications (GPS) - Surface texture: Profile method - Metrological characteristics of phase correct filters. 3 Definitions For the purposes of this part of IS0 13565, the definitions given in IS0 3274 and IS0 4287 apply. -,-,- STD-IS0 135
27、L5-L-ENGL L97b El 4853903 0733875 52T IS0 13565-1:1996(E) 0 IS0 4 Reference guide To measure profiles in accordance with this part of IS0 13565, a measuring system which incorporates an external reference is recommended. In case of arbitration the use of such a system is obligatory. 5 Traversing dir
28、ection The traversing direction shall be perpendicular to the direction of lay unless otherwise indicated. 6 Filtering process to determine the roughness profile The filtering process is carried out in several stages giving the modified profiles, sections of which are illustrated in figure la) to d)
29、. The first mean line is determined by a preliminary filtering of the primary profile with the phase correct filter in accordance with IS0 11562 using a cut-off wavelength Ac in accordance with clause 7 and corresponding measuring conditions in accordance with table 1 of IS0 3274:1996. All valley po
30、rtions which lie below this mean line (shown hatched in figure la) are removed. In these places the primary profile is replaced by the curve of the mean line. The same filter is used again on this profile with the valleys suppressed. The second mean line thus obtained (see figure 1 b) is the referen
31、ce line relative to which the assessment of profile parameters is performed. This reference line is tranferred to the original primary profile (see figure IC) and the roughness profile according to this part of IS0 13565 is obtained from the difference between the primary profile and the reference l
32、ine (see figure 1 d). 7 Selection of the cut-off wavelength A c and the evaluation length In The measurements shall preferably be carried out using a cut-off wavelength of Ac = 0,8 mm. In justified exceptional cases, Ac = 2,5 mm may be selected and this shall be stated in the specification and test
33、results. Table 1 provides the relationship between cut-off wavelength Ac and the evaluation length In Table 1 - Relationship between the cut-off wavelength Ac and the evaluation length In Dimensions in millimetres ac In 4 12,5 2 -,-,- Pm 5 L- Mean line 2.5 - O l a) Unfiltered primary profile (valley
34、s shown hatched) I I 2.5 I I T I i*m Reference line for roughness measurement 5- 2.5 I I 1 b) Unfiltered primary profile after suppression of valleys i*m 5- O I cl Position of the reference line in the primary profile 5 2.5 II I O I 2 mm 1 U d) Roughness profile in accordance with this standard Figu
35、re 1 - Filtering process 3 IS0 13565-1:1996(E) Chain link number 11121314 Annex A (informative) 5 6 Relation to GPS matrix model Size I For full details about the GPS matrix model see ISO/TR 14638. I A.l Information about this part of IS0 13565 and its use This part of IS0 13565 describes a filterin
36、g method for use with surfaces that have deep valleys below a more finely finished plateau with a relatively small amount of waviness. The roughness profile generated using the filter defined in IS0 11562 suffers some undesirable distortions, when measuring this type of surface, which is very common
37、. Distance This method serves to reduce these distortions, thus enabling the parameters defined in IS0 13565-2 and IS0 13565-3 to be used for evaluating the above-mentioned type of surface, with minimal influence from these distortions. I I I l A.2 Position in the GPS matrix model Total run-out I I
38、This part of IS0 13565 is a General GPS standard, which influences the chain links 2 and 3 of the chain of standards for roughness profile in the General GPS matrix, as graphically illustrated in figure A.1. I I Fundamental GPS standards Global GPS standards General GPS matrix Angle Form of line ind
39、ependent of datum Form of line dependent on datum Form of surface independent of datum Form of surface dei3endent on datum I Orientation IIIIIII I Location IIIIIII I Circular run-out IIIIIII Figure A.l A.3 Related standards The related International Standards are those of the chains of standards ind
40、icated in figure A.l. 4 -,-,- SD-IS0 135b5-L-ENGL 199b W Li851903 0733878 239 W Q IS0 IS0 13565-1 : 1996( E) Annex B (inform at ive) Bibliography 1 IS0 13565-2:1996, Geometrical Product Specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 2:
41、 Height characterization using the linear material ratio curve. IS0 13565-3:-1), Geometrical Product Specifications (GPS) - Surface texture: Profile method; Surfaces having stratified functional properties - Part 3: Height characterization using the material probability curve. I31 ISODR 14638:1995,
42、Geometrical Product Specifications (GPS) - Masterplan. I41 VIM - International vocabulary of basic and general terms in metrology. BIPM, IEC, IFCC, ISO, IUPAC, IUPAP, OIML, 2nd edition, 1993. 2 1) To be published. 5 STD-IS0 L35bS-L-ENGL 397b q85L903 0733877 175 IS0 IS0 13565-1 :1996(E) ICs 17.040.20 Descriptors: surface properties, surface condition, determination, characteristics, texture profiles, roughness measurement, general conditions, geometrical product specifications Price based on 5 pages