《ISO-5610-1998.pdf》由会员分享，可在线阅读，更多相关《ISO-5610-1998.pdf（16页珍藏版）》请在三一文库上搜索。
1、A Reference number ISO 5610:1998(E) INTERNATIONAL STANDARD ISO 5610 Fifth edition 1998-11-15 Single-point tool holders for turning and copying, for indexable inserts Dimensions Porte-plaquette de tournage et de copiage active unique Dimensions Copyright International Organization for Standardization
2、 Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5610:1998(E) ISO 1998 All rights reserved. Unless otherwise specified, no part of this publication
3、may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 CH-1211 Genve 20 Switzerland Internetisoiso.ch Printed in Switze
4、rland ii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for
5、which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non- governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on a
6、ll matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS
7、O 5610 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials. This fifth edition cancels and replaces the fourth edition (ISO 5610 :1995), subclause 4.4.1 and the first sentence of subclause 4.4.4 of which have been mod
8、ified. In addition clause 5 (table 5) has been augmented by inclusion of tool holder, style L for W-shape inserts. Annex A of this International Standard is for information only. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical S
9、tandards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISOISO 5610:1998(E) 1 Single-point tool holders for turning and copying, for indexable inserts Dimensions 1 Scope This International Standard spe
10、cifies the general dimensions of turning and copying single-point tool holders for indexable inserts, and specifies preferred tool holders (see clause 5). 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this Internation
11、al Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreement based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of
12、 IEC and ISO maintain registers of currently valid International Standards. ISO 3002-1 :1982, Basic quantities in cutting and grinding Part 1 : Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers. 3 Remark The designation of turning a
13、nd copying tool holders is dealt with in ISO 5608; however, it should be noted that for preferred tool holders in accordance with clause 5, a dash replaces the letter symbol identifying tool length. 4 Dimensions 4.1 Shank See figure 1 and table 1. Copyright International Organization for Standardiza
14、tion Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5610:1998(E) ISO 2 Figure 1 Table 1 Dimensions in millimetres h h1381012162025324050 b h13 b =
15、h b = 0,8 h 810 8 12 10 16 12 20 16 25 20 32 25 40 32 50 40 l1 k16 long tool holders short tool holders 60 40 70 50 80 60 100 70 125 80 150 100 170 125 200 150 250 h1 js14h1 = h 4.2 Head length l2 See figure 1 and table 2. The head lengths given in table 2 do not apply to tool holders with rhombic i
16、ndexable inserts shapes D and V (see ISO 5608). Table 2 Dimensions in millimetres Diameter of the inscribed circle of the insert l2 max. 6,3525 9,52532 12,736 15,87540 19,0545 25,450 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technic
17、al Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISOISO 5610:1998(E) 3 4.3 Dimensions f See the figures in clause 5 and table 3. Table 3 Dimensions in millimetres f bSeries 11)Series 2Series 3Series 4Series 5 + 0,
18、5 0 + 0,5 0 + 0,5 0 + 0,5 0 8478,5910 105910,51112 1261112,51316 1681316,51720 20101720,52225 2512,52225,52732 321627333540 402035414350 502543515360 For tool holders style D, N, VB, TARF, G, H, J, K, L, S 1) Tolerance for symmetrical tool holders (styles D and V): Tolerance for non-symmetrical tool
19、 holders (style N): 0,25 + 0,5 0 4.4 Identification of dimensions l1, f and h1 4.4.1 The length dimension l1 is the distance from the specified point K (see figures 2 to 5) to the end of the shank. Dimension f is the distance between the specified point K and the rear backing surface of the tool hol
20、der. Dimension h1 is the height of specified point K above the base of the tool holder. The values of l1 as specified in 4.1, f as specified in 4.3 and h1, as specified in 4.1 are given for tool holders equipped with master inserts having corner radii in accordance with 4.4.3. For tools style S, sid
21、e rake is equal to back rake. Special case of tool styles D and S with round inserts: For tools style D (see figure 6), point K is defined as the intersection of: a plane parallel to Pf passing through the axis of the insert; a plane perpendicular to Pf and tangential to the cutting edge; a plane co
22、ntaining Ag. For tools style S (see figure 7), there are two cases of point K. These are defined by two planes Pf in directions of two main perpendicular feeds and which are tangential to the cutting edge of the insert. Copyright International Organization for Standardization Provided by IHS under l
23、icense with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5610:1998(E) ISO 4 Figure 2Figure 3 Figure 4Figure 5 Copyright International Organization for Standardization Provided by I
24、HS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISOISO 5610:1998(E) 5 Figure 6Figure 7 4.4.2 The specified point K is defined as follows: Consider planes Pf (assumed
25、 working plane) and Ps (tool cutting edge plane) according to ISO 3002-1 for a selected point on the major cutting edge (for example point of tangency of major cutting edge with inscribed circle). a)For kr 90, point K is defined as the intersection of plane Ps, a plane parallel to plane Pf tangent t
26、o the corner radius and a plane containing the tool face Ag (see figures 2 and 3). b)For kr . 90, point K is defined as the intersection of a plane parallel to plane Pf tangent to the corner radius, a plane perpendicular to plane Pf tangent to the corner radius and a plane containing the tool face A
27、g (see figures 4 and 5). 4.4.3 The corner radius re of the master inserts used for the definition of dimensions l1, f and h1 is a function of the diameter of the inscribed circle of the insert, as indicated in table 4. Table 4 Dimensions in millimetres Diameter of the inscribed circle 6,357,949,5251
28、2,715,87519,0525,4 Corner radius re (nominal) 0,40,81,22,4 NOTE 1 Dimensions l1, f and h1 are based on corner radii re converted from inch values, i.e. re = 0,397 mm, 0,794 mm, 1,191 mm and 2,381 mm. 4.4.4 The tolerance 0,25 mm on dimension f for series 1 refers to symmetrical tool holders (styles D
29、 and V). Therefore, deviating from the definition given in 4.4.2, the values in table 3 are given in relation to the theoretical intersection of the cutting edges (theoretical corner T). For particular tool holders, dimension f shall be given in accordance with the definition in 4.4.2, and shall the
30、refore be corrected to a value rounded off to 0,1 mm depending on the included angle er, the corner radius re (see 4.4.6) and the cutting edge angle kr. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not
31、for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5610:1998(E) ISO 6 4.4.5 The tolerance 0,25 mm on dimension f for series 1 does not include the tolerance on the shank width b. 4.4.6 Tool holders may be equipped with inserts of size in acc
32、ordance with clause 5 and any corner radius re. For corner radii re other than those specified in 4.4.3, dimensions l1 and f shall be corrected by using the values x and y (see figures 2 to 5), which are the distances from the specified point K to the theoretical corner T. The new dimensions l1 and
33、f are found from the differences between x and y corresponding to the corner radius according to 4.4.3, and x and y corresponding to the real corner radius. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001
34、Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISOISO 5610:1998(E) 7 5 Preferred tool holders See table 5. Table 5 Dimensions in millimetres Style h b l1 k16 h1 js14 08 08 60 8 10 10 70 10 12 12 80 12 16 16 100 16 20 20 125 20 25 25 150
35、25 32 25 170 32 32 32 170 32 40 32 150 40 40 32 200 40 40 40 200 40 50 50 250 50 A f 0 0 5+, (series 3) l (desig- nation l2 max. 8,5 06 25 10,5 06 25 f 0 0 5+, (series 3) l (desig- nation l2 max. 12,5 11 25 16,5 11 25 20,5 16 32 25,5 16 32 25,5 16 32 33 22 36 41 22 36 B f 0 0 5+, (series 2) l (desig
36、- nation l2 max. a 1) 7 06 25 1,6 9 06 25 1,6 11 06 25 1,6 f 0 0 5+, (series 2) l (desig- nation l2 max. a 1) 13 09 32 2,2 17 12 36 3,1 22 12 36 3,1 22 12 36 3,1 27 19 45 4,6 35 19 45 4,6 43 25 50 5,9 Copyright International Organization for Standardization Provided by IHS under license with ISO Lic
37、ensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5610:1998(E) ISO 8 Table 5 (continued) Style h b l1 k16 h1 js14 08 08 60 8 10 10 70 10 12 12 80 12 16 16 100 16 20 20 125 20 25 25 150 25 32 2
38、5 170 32 32 32 170 32 40 32 150 40 40 32 200 40 40 40 200 40 50 50 250 50 D 2) f 0,25 (series 1) l (desig- nation l2 max. 6 09 32 8 09 32 10 12 36 12,5 12 36 12,5 12 36 16 19 45 f 0,25 (series 1) d (desig- nation 4 06 5 06/08 6 06/08 8 06/ 08/10 10 06/ 08/ 10/12 12,5 06/ 08/ 10/ 12/ 16 12,5 12/16 16
39、 20 20 25 F f 0 0 5+, (series 5) l (desig- nation l2 max. 10 06 25 12 06 25 f 0 0 5+, (series 5) l (desig- nation l2 max. 16 11 25 20 11/16 25/32 25 16 32 32 16/22 32/36 32 16/22 32/36 40 22 36 50 22/27 36/40 Copyright International Organization for Standardization Provided by IHS under license with
40、 ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISOISO 5610:1998(E) 9 Table 5 (continued) Style h b l1 k16 h1 js14 08 08 60 8 10 10 70 10 12 12 80 12 16 16 100 16 20 20 125 20 25 25 150
41、25 32 25 170 32 32 32 170 32 40 32 150 40 40 32 200 40 40 40 200 40 50 50 250 50 G f 0 0 5+, (series 5) l (desig- nation l2 max. 10 06 25 12 06 25 f 0 0 5+, (series 5) l (desig- nation l2 max. 16 11 25 20 11/16 25/32 25 16 32 32 16/22 32/36 32 16/22 32/36 40 22 36 50 22/27 36/40 60 27 40 H f 0 0 5+,
42、 (series 5) l (desig- nation l2 max. 12 07 25 16 07/11 25/32 20 11 32 25 11/15 32/40 32 15 40 32 15 40 f 0 0 5+, (series 5) l (desig- nation l2 max. 16 11/13 25/32 20 11/13 25/32 25 13/16 32/40 32 16 40 32 16 40 Copyright International Organization for Standardization Provided by IHS under license w
43、ith ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5610:1998(E) ISO 10 Table 5 (continued) Style h b l1 k16 h1 js14 08 08 60 8 10 10 70 10 12 12 80 12 16 16 100 16 20 20 125 20 25 25
44、 150 25 32 25 170 32 32 32 170 32 40 32 150 40 40 32 200 40 40 40 200 40 50 50 250 50 f 0 0 5+, (series 5) l (desig- nation l2 max. 10 07 25 12 07 25 16 11 32 20 11 32 25 15 40 32 15 40 32 15 40 40 15 40 J f 0 0 5+, (series 5) l (desig- nation l2 max. 25 16 32 32 16/22 32/36 32 16/22 32/36 40 22/27
45、36/40 f 0 0 5+, (series 5) l (desig- nation l2 max. 16 11/13 25/32 20 11/13 25/32 25 13/16 32/40 32 16 40 32 16 40 K f 0 0 5+, (series 5) l (desig- nation l2 max. a 1) 10 06 25 1,6 12 06 25 1,6 f 0 0 5+, (series 5) l (desig- nation l2 max. a 1) 16 09 32 2,2 20 09/12 32/36 2,2/3,1 25 12 36 3,1 32 12/
46、19 36/45 3,1/4,6 32 12/19 36/45 3,1/4,6 40 19 45 4,6 50 19/25 45/50 4,6/5,9 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:37:47 MDTNo reproduction or networking permitted wi
47、thout license from IHS -,-,- ISOISO 5610:1998(E) 11 Table 5 (continued) Style h b l1 k16 h1 js14 08 08 60 8 10 10 70 10 12 12 80 12 16 16 100 16 20 20 125 20 25 25 150 25 32 25 170 32 32 32 170 32 40 32 150 40 40 32 200 40 40 40 200 40 50 50 250 50 L f 0 0 5+, (series 5) l (desig- nation l2 max. 10 06 25 12 06 25 16 09 32 20 09/19 32/36 25 12 36 32 12/19 36/45 32 12/19 36/45 40 19 40 50 19 45 f 0 0 5+, (series 5) l for inserts style W (desig- nation l2 max. 10 04 25 12 04 25 16 04 25 20 06 36 25 06/ 08 36/ 45 32 06/ 08 36/ 45 32 06/ 08 36/ 45 40 08 45 N f 0 0 5+, (series 1) l (des