《ISO-5446-1980.pdf》由会员分享，可在线阅读，更多相关《ISO-5446-1980.pdf（6页珍藏版）》请在三一文库上搜索。
1、International Standard INTERNATIONAL ORGANIZATION FOR STANDARDlZATlON*MEYHAPOLHAR OPTAHHBALWIR n0 CTAHAAPTbI3Al.W.ORGANlSATlON lNTERNATlONALE DE NORMALISATION Ferromanganese - Specification and conditions of delivery Ferro-manganbe - Spkifications et conditions de livraison First edition - 1980-12-1
2、5 3 UDC 669.15 74-198 Ref. No. IS0 5446-1980 (E) see IS0 565. 5.3.2 If the purchaser requires particle size ranges and/or tolerances other than those given in table 7, these shall be agreed upon between supplier and purchaser. 5.4 Extraneous contamination The material shall be as free as possible fr
3、om extraneous con- tamination. 6 Testing 6.1 Sampling for chemical analysis and sieve analysis 6.1.1 Sampling for chemical analysis and sieve analysisa shall preferably be carried out by the method specified in IS0 3713sj, but other methods of sampling having similar precision may also be used. 6.1.
4、2 Sampling is usually carried out at the supplier s stockyard, unless otherwise agreed. Wherever sampling is car- ried out, representatives of both supplier and purchaser may be present. 6.1.3 If required, arbitration sampling shall be carried out by an arbitrator chosen by mutual agreement between
5、supplier and purchaser. Sampling shall be carried out by the method specified in IS0 371331, but other methods of sampling having similar precision may be agreed upon between supplier, pur- chaser and arbitrator. The sample obtained by arbitration shall be accepted by both parties. 6.2 Analysis 6.2.
6、1 The chemical analysis of ferromanganese shall preferably be carried out by the method specified in IS0 4159, but other methods of chemical analysis having similar precision may also be used. 6.2.2 Ferromanganese shall be furnished with an analysis cer- tificate, established by the supplier, for th
7、e manganese content and, if agreed, the contents of other elements either specified in tables 1 to 6 or additionally agreed and, upon request of the purchaser, with a sample representative of the consignment. 6.2.3 In case of dispute, one of the following two procedures may be used. 6.2.3.1 Contradi
8、ctory analysis The chemical analysis shall be carried out on the same sample and preferably by the method specified in IS0 4159. Other methods of chemical analysis having similar precision may be used, but shall be agreed upon between supplier and pur- chaser. If the difference between the results o
9、f the two analyses is within x %4), the mean value shall apply. If the difference ex- ceeds x %, then, provided that no other agreement is reached, arbitration analysis shall be carried out by an arbitrator chosen by mutual agreement between supplier and purchaser. 1) The point of delivery is define
10、d as that point where the responsibility for the consignment passes from supplier to purchaser. If neither the supplier nor the purchaser is responsible for the transportation, then the point at which the values become valid shall be agreed upon. 2) Sieve analysis of ferroalloys will form the subjec
11、t of IS0 4551. 3) A method of sampling specific to ferromanganese will form the subject of IS0 4553. 4) The value of x will be specified later. In the meantime, the value should be agreed upon between purchaser and supplier. 2 Copyright International Organization for Standardization Provided by IHS
12、under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 00:05:52 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 5446-1990 (E) 6.2.3.2 Arbitration analysis disputed values or not more than y %tr outside one of these values. Arbit
13、ration analysis shall preferably be carried out by the method specified in IS0 4159. Other methods of chemical analysis having similar precision may be used, but shall be agreed upon between supplier, purchaser and arbitrator. 7 Despatch and storage The arbitrator s result is final, provided it is w
14、ithin the two Ferromanganese shall be packed, stored and transported according to international regulations.zr Table 1 - High carbon FeMn Designation Mn Chemical composition, % C Si P S max. max. max. max. FeMn75C80VHP FeMn75C80MP From 70.0 up to and including 82,0 W 2.0 0,030 FeMn75C80VLP Table 2 -
15、 Medium carbon FeMn Designation Mn Chemical composition, % C Si P S over up to and max. max. max. including I,5 2.0 LO 0,35 0.20 From 75.0 up to and including 85,0 ,O 1,5 2.0 0,35 0,030 0.20 0.5 1.0 2.0 0,35 0.20 Table 3 - Medium carbon FeMn Designation il;, FeMn90C20 FeMnSOC20LP FeMn90C15 FeMnSOCl5
16、LP Over 85,0 up to and including 95,0 185 2,o LO 0.35 0,20 0,35 - 8 1,5 2.0 0,030 0.20 I I I I I FeMn90ClO FeMnSOClOLP 0.5 18 2.0 0,35 0,20 I) This value, as an overall precision, will be specified as &-JM. 2) Examples of appropriate international regulations are : a) RID : Reglement International c
17、oncernant le transport des marchandises dangereuses par chemin de fer, Annexe C. b) International maritime dangerous goods code. 3 , Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/20
18、07 00:05:52 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 5446-1980 (E) Table 4 - Low carbon FeMn Chemical composition, % Designation I I Mn C over I up to and including Si P I I S max. max. max. 0.10 l-l 2.0 TO 0.30 0,15 I4 0,030 03 0.15 Table 5 - Low carbon FeMn Des
19、ignation Mn Chemical composition, % C Si P s over up to and max. max. max. including Over 85.0 up to and including 95,0 Table 6 - FeMn, nitrogen-containing Smelted Sintered Sintered Designation FeMn8OC05N2 FeMn70C05N5 FeMn70ClONS Mn min. NO 89.0 Chemical composition, % C Si P S N over up to and max.
20、 max. max. over up to and including including or1 0,5 2 0,15 0,030 1,5 23 a1 0,5 2 0,30 0,15 0,030 4.0 8,O 035 zo 2 0,35 0,20 0,030 Table 7 - Particle size Class Particle size range Undersize, max. % by mass Oversize, max. mm total below 3,15 mm % by mass 1 loo to 315 15 57 10 2 25 to 200 15 7 ) No
21、piece to ex- 3 10 to 100 15 7 ) teed 1,15 x the maximum limit of 4 3.15 to 50 7 the size range 5 3,15 to 25 7 specified in two 8 up to 3,15 - or three directions. 1) If not otherwise specified, these values are for information only. 4 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/28/2007 00:05:52 MDTNo reproduction or networking permitted without license from IHS -,-,-