《ISO-6413-1988.pdf》由会员分享，可在线阅读，更多相关《ISO-6413-1988.pdf（8页珍藏版）》请在三一文库上搜索。
1、INTERNATIONAL STANDARD INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION MEXAYHAPOAHAR OPrAHM3AllR I-IO CTAHAAPTklSAWkl Technical drawings - Representation of splines and serrations Dessins techniques - Reprksentation des cannelures et des dentelures IS0 641
2、3 First edition 1988-12-01 Reference number IS0 6413 : 1988 (E) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 20:05:19 MDTNo reproduction or networking permitted without licens
3、e from IHS -,-,- IS0 6413 : 1989 (El Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body
4、interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrote
5、chnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the IS0 Council. They are approved in accordance with
6、IS0 procedures requiring at least 75 % approval by the member bodies voting. International Standard IS0 5413 was prepared by Technical Committee ISO/TC 10, Technical drawings. Annex A forms an integral part of this International Standard. 0 International Organization for Standardization. 1988 Printe
7、d in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 20:05:19 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 641
8、3 : 1999 (E) Technical drawings - Representation of splines and serrations 1 Scope This International Standard specifies the rules and graphical symbols for the representations of splines and serrations on technical drawings. Two methods of representation are specified as follows : a1 true represent
9、ation; b) simplified representation. The rules and graphical symbols specified in this International Standard are applicable to detail drawings of the parts (shafts and hubs) and to assembly drawings of joints. NOTE - For uniformity all figures in this International Standard are drawn in the first-a
10、ngle orthographic projection. It should be understood that the third-angle orthographic projection could equally well have been used without prejudice to the principles established. 3 Definitions For the purposes of this International Standard, the following definitions apply. 3.1 spline joint : Con
11、necting, co-axial, elements that trans- mit torque through the simultaneous engagement of equally spaced teeth situated around the periphery of a cylindrical external member with similar spaced mating spaces situated around the inner surface of the related cylindrical internal member. ISO 4156 : 198
12、11 3.2 involute spline : One member of a spline joint having teeth or spaces that have involute flank profiles. lSO4156: 19811 3.3 straight-sided spline : One member of a spline joint having teeth or spaces that have straight-sided flank profiles. 3.4 serration : One member of a spline joint having
13、teeth or spaces that generally have flank profiles of 60 pressure angle. 2 Normative references The following standards contain orovisions which, throuah reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All s
14、tandards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards listed below. Members of IEC and IS0 maintain registers of currently valid International Standards. 4 D
15、esignation The designation of spline joints shall consist of the graphical symbol of the type and the designation of joint specified in the relevant International Standard (see clause 2) or any other stan- dard dealing with this subject. 4.1 Graphical symbols IS0 14 : 1982, Straight-sided splines fo
16、r cylindrical shafts with in ternal ten tering - Dimensions, tolerances and verification. IS0 128 : 1982, Technical drawings - General principles of presentation. The type of spline joint is indicated by graphical symbols. The graphical symbols for the straight-sided spline (see IS0 14) are shown in
17、 figure 1 and for the involute spline (see IS0 41%) and for serrations are shown in figure 2. IS0 3998-l : 1974, Technical drawings - Lettering - Part 1: CurrenUy used characters. IS0 3461-2 : 1987, General principles for the creation of graphical s ymbols - Part 2 : Graphical symbols for use in tec
18、h- nical product documentation. IS0 4156 : 1981, Straight cylindrical involute splines - Metric module, side fit - Generalities, dimensions and inspection. I-L A Figure 1 Figure 2 The proportion and dimensions of the graphical symbols are specified in annex A. 1 Copyright International Organization
19、for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 20:05:19 MDTNo reproduction or networking permitted without license from IHS -,-,- 1s0 6413 : 1988 (El 4.2 Method for indicating designation The designation should be
20、indicated near the feature but always connected to the contour of the spline joint by a leader line (see figure 3). Figure 3 Where a spline joint is not in accordance with a standard as mentioned above, or where the requirement is modified, the necessary data shall be tabulated on the drawing or any
21、 other associated document and shall be cross-referenced by a leader line and graphical symbol to the applicable contour. 5 Complete representation of spline joints A complete representation of spline joints showing all details with their true dimensions is generally not necessary in a technical dra
22、wing and should be avoided. If such a representation has to be made, the drawing rules laid down in IS0 128 shall be applied. If necessary, a designation of the spline joint in accordance with clause 4 may be added. Figure 4 shows an example of a complete representation of a straight-sided spline jo
23、int. Figure 4 Figure 5 shows an example of a complete representation of an involute spline joint. Figure 5 Figure 6 shows an example of a complete representation of a serration. + Figure 6 6 Simplified representation 6.1 General A simplified representation for straight-sided splines and for in- volu
24、te splines as shown in table 1 is usually adequate to convey all the necessary information. 2 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 20:05:19 MDTNo reproduction or netwo
25、rking permitted without license from IHS -,-,- IS0 6413 : 1988 (El Table 1 - Simplified representation Straight-sided splines Involute splines and serrations A-L. ) A. ) 1) If necessary, the designation of the spline joint in accordance with clause 4 shall be added (for examples, see figures 13 and
26、14). 6.2 Representation of details (shafts and hubs) As a fundamental principle, the parts of a spline joint shall be represented as a solid part without teeth, but with the addition of the root surface in a continuous thin line (see IS0 128, line type B) or the pitch surface in a thin chain line (s
27、ee IS0 128, line type G). 6.2.1 Contours and edges The contours and edges of a shaft (e.g. an external spline) or a hub (e.g. an internal spline) shall be drawn as if they were - in an unsectioned view, solid parts (without teeth) bounded by a cylinder representing the tip surface (outside diameter,
28、 for example, of an external spline or inside diameter, for example, of an internal spline); - in an axial section, a shaft or hub having two diametri- cally opposed teeth (shown unsectioned), regardless of tooth spacing. 6.2.2 Root surface For straight-sided splines, the root surface (minor diamete
29、r of external splined part, major diameter of internal spline) shall be drawn with a continuous thin line (see IS0 128, line type B). In the axial section of a splined shaft or hub, however, the root surface shall be drawn with a continuous thick line (see IS0 128, line type A) in accordance with ta
30、ble 1. 3 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 20:05:19 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6413 : 1988 (El 6.2.3 Pitch surfac
31、e 6.2.7 Detailed drawing of tooth profile The pitch surface (pitch diameter) shall be drawn with a thin chain line (see IS0 128, line type G) for involute splines and ser- rations. If the designation is not sufficiently clear, a detailed drawing of the tooth profile should be added (see figure IO).
32、6.2.4 Usable length The usable length of the splined part shall be represented with a continuous thick line (see IS0 128, line type A) (see figure 7). Usually, only the usable length of a splined part shall be drawn. 6.2.5 Tool run-out Figure IO If necessary, the tool run-out may be represented by a
33、n oblique line or a radius with the same line as used for the root surface (see figures 7 and 8). Figure 7 Figure 8 6.2.8 Surface texture If it is necessary to specify the surface texture of the contacting surfaces (excluding root and tip diameter), the graphical sym- bol, the designation and the dr
34、awing indications used for sur- face texture should be indicated on a common leader line as shown in figure 11. I,6 J-llSO14-6x23f7x26 d Figure 11 6.2.6 Position of teeth 7 Assembly drawings If it is essential to indicate the position of the teeth in relation to a given axial plane, one or two teeth
35、 may be drawn with a con- tinuous thick line (see IS0 128, line type A) (see figure 9). The rules specified for the representation of details are also ap- plicable to assembly drawings (see figure 12). .j . + / Figure 9 Figure 12 4 Copyright International Organization for Standardization Provided by
36、 IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 20:05:19 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 5413 : 1955 (El In assembly drawings, the designations of both parts (hub and shaft) shall be combined as shown
37、 in figures 13 and 14. J-l IS0 14-6x23H7lf7x26 AlNT/EXT24Zx2,5mx30Rx5H15f I IS0 4156 Figure 13 I +z- -_-.-.-.- - A- _-.- Figure 14 Annex A (normative) Proportions and dimensions of graphical symbols In order to harmonize the sizes of the graphical symbols specified in this International Standard wit
38、h those of the other drawing indications, the following rules, in accordance with IS0 3481-2, shall be applied. A.1 General requirements A.l.l The graphical symbols shown in clause 4 shall be in- dicated using a line thickness d equal to one-tenth of the height h of the lettering used for the dimens
39、ions in the relevant drawing. A.1.2 The numerals and letters used for the additional specifications shall be drawn using the same line thickness d, height h and type of lettering as used for dimensions in the rele- vant drawing, and in accordance with IS0 3898-l (lettering type B, vertical). A.2 Pro
40、portions The graphical symbols shall be drawn in accordance with figures A.1 and A.2. Figure A.1 A.3 Dimensions Figure A.2 The range of sizes to be used for the graphical symbols and additional specifications are given in table A. 1. Table A.1 - Dimensions Dimensions in millimetres Height of numeral
41、s and letters, h 3,5 5 7 10 14 20 Line thickness for symbols, d , and lettering, d 0,35 0,5 0.7 1 1.4 2 Height of symbol, h 3,5 5 7 10 14 20 5 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale
42、, 04/26/2007 20:05:19 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6413 : 1666 (E) UDC 744.4 : 621-46 Descriptors : drawings, technical drawings, splines, graphic methods. Price based on 5 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 20:05:19 MDTNo reproduction or networking permitted without license from IHS -,-,-