《ISO-6395-2008.pdf》由会员分享，可在线阅读，更多相关《ISO-6395-2008.pdf（50页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 6395:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 6395 Second edition 2008-03-15 Earth-moving machinery Determination of sound power level Dynamic test conditions Engins de terrassement Dtermination du niveau de puissance acoustique Conditions dessai dynamique ISO 6395:2008(E) P
2、DF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, p
3、arties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relati
4、ve to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIG
5、HT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
6、 ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reserved -,-,- ISO 6395:2008(E) ISO 2008 All rights reserved
7、iii Contents Page Foreword. v Introduction. vi 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 1 4 Instrumentation. 2 5 Test environment 2 5.1 General. 2 5.2 Test site and environmental correction, K2A 2 5.3 Test site . 3 5.4 Background noise correction, K1A 4 5.5 Climatic conditions.
8、 4 6 Measurement of time-averaged A-weighted sound pressure levels. 4 6.1 Size of measurement surface 4 6.2 Microphone positions on the hemispherical measurement surface. 4 6.3 Positioning the machine 5 7 Set-up and operation of machine 6 7.1 General. 6 7.2 Engine speed. 7 7.3 Fan speed 7 7.4 Travel
9、 mode operation of machine. 7 8 Determination of A-weighted sound power level 8 8.1 Measurement procedure 8 8.2 Calculation of A-weighted sound power level. 8 8.3 Determination of measurement result 9 9 Information to be recorded 9 10 Information to be reported. 10 10.1 Information 10 10.2 Declarati
10、on of sound emission data and uncertainty. 10 Annex A (normative) Basic length, l, and additional machine specifications. 11 Annex B (normative) Excavators (hydraulic or cable-operated). 23 Annex C (normative) Dozers. 25 Annex D (normative) Loaders. 26 Annex E (normative) Backhoe loaders 28 Annex F
11、(normative) Dumpers 30 Annex G (normative) Graders. 32 Annex H (normative) Landfill compactors. 33 Annex I (normative) Trenchers . 34 Annex J (normative) Scrapers 35 Annex K (normative) Pipelayers. 37 -,-,- ISO 6395:2008(E) iv ISO 2008 All rights reserved Annex L (normative) Ride-on operated rollers
12、39 Annex M (informative) Additional guidelines for measurement of A-weighted sound power level of earth-moving machinery Dynamic test conditions.41 Annex N (normative) Declaration of sound emission data and uncertainty 42 Bibliography .43 -,-,- ISO 6395:2008(E) ISO 2008 All rights reserved v Forewor
13、d ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technica
14、l committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of ele
15、ctrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to th
16、e member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for ide
17、ntifying any or all such patent rights. ISO 6395 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 2, Safety requirements and human factors in collaboration with Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 1, Noise. This second edition cancels and
18、replaces the first edition (ISO 6395:1988), which has been technically revised. It also incorporates the Amendment ISO 6395:1988/Amd. 1:1996. ISO 6395:2008(E) vi ISO 2008 All rights reserved Introduction This International Standard is a specific test code for earth-moving machinery as defined in ISO
19、 6165. A simulated dynamic test condition, rather than an actual work cycle, is used. Simulated dynamic test conditions provide noise emission data which are repeatable and representative. Actual work cycle tests are complex and repeatability can be a problem. Specific procedures are described in th
20、is International Standard to enable the sound power emission in dynamic test conditions to be determined in a manner which is repeatable. Attachments (bucket, dozer, etc.) for the manufacturers production version are intended to be fitted since this is the configuration most likely to exist when the
21、 machine is in actual use. This International Standard enables compliance with noise limits to be determined, if applicable. It can also be used for evaluation purposes in noise reduction investigations. A complementary test code is given in ISO 6396. This other specific test code is intended to be
22、used to determine the noise emitted by earth-moving machinery, measured at the operators position in terms of the A-weighted sound pressure level with the machine under dynamic test conditions. Corresponding measurements of noise emitted to the environment and noise at the operators position under s
23、tationary test conditions are described in ISO 6393 and ISO 6394, respectively. INTERNATIONAL STANDARD ISO 6395:2008(E) ISO 2008 All rights reserved 1 Earth-moving machinery Determination of sound power level Dynamic test conditions 1 Scope This International Standard specifies a method for determin
24、ing the noise emitted to the environment by earth- moving machinery, measured in terms of the A-weighted sound power level while the machine is operating under dynamic test conditions. It is applicable to earth-moving machinery as specified in Annex A and as defined in ISO 6165. 2 Normative referenc
25、es The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3744:1), Acoustics Determination of sound
26、power levels and sound energy levels of noise sources using sound pressure Engineering method for an essentially free field over a reflecting plane ISO 6165, Earth-moving machinery Basic types Identification and terms and definitions ISO 6393:2008, Earth-moving machinery Determination of sound power
27、 level Stationary test conditions ISO 9249, Earth-moving machinery Engine test code Net power IEC 61672-1, Electroacoustics Sound level meters Part 1: Specifications 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 3744, ISO 6165 and the following app
28、ly. 3.1 time-averaged A-weighted sound pressure level LpA,T A-weighted sound pressure level averaged on an energy basis over the whole measurement period, T 3.2 A-weighted sound power level LWA quantity obtained from the time-averaged A-weighted sound pressure levels averaged over the measurement su
29、rface on an energy basis 1) To be published. (Revision of ISO 3744:1994.) -,-,- ISO 6395:2008(E) 2 ISO 2008 All rights reserved 3.3 basic length l length used to define the radius of the measurement hemisphere NOTE The dimension of the basic length, l, is determined in Annex A. 3.4 Machine centre po
30、int 3.4.1 machine centre point all machines, except those with slewing upper structure midpoint of the basic length, l, at the machine longitudinal centre line 3.4.2 machine centre point machines with slewing upper structure centre of rotation of the upper structure 3.5 Fan speed 3.5.1 maximum worki
31、ng speed of the fan fan speed at which the fan provides maximum cooling performance for the machine under the most severe operating conditions 3.5.2 fan drive with continuous variable fan speed fan drive that varies the fan speed continuously throughout a variable range to minimize its speed for the
32、 needed cooling performance in relation to the heat load 4 Instrumentation The instrumentation shall be capable of carrying out the measurements according to Clause 8. The preferred instrumentation system for acquiring the data is an integrating-averaging sound level meter complying with the require
33、ments of IEC 61672-1 for a class 1 instrument. 5 Test environment 5.1 General For the purposes of this International Standard, the test environment specified in ISO 3744:, Clause 4 and Annex A, apply. Additional requirements are given in 5.2 to 5.5. Humidity, air temperature, barometric pressure, vi
34、bration and stray magnetic fields shall be within the limits specified by the manufacturer of the instrumentation. 5.2 Test site and environmental correction, K2A For test-site measurement ground surfaces consisting of a hard reflecting plane such as concrete or non- porous asphalt (5.3.1 a) and b)
35、and having negligible sound-reflecting obstacles within a distance from the source equal to three times the measurement hemisphere radius, it may be assumed that the absolute value of environmental correction, K2A, is less than or equal to 0,5 dB, and can therefore be disregarded. In this case, K2A
36、shall be equal to 0 dB. For the all-sand test site 5.3.1 c), the value of environmental correction, K2A, shall be determined and used in the sound power calculation. -,-,- ISO 6395:2008(E) ISO 2008 All rights reserved 3 5.3 Test site 5.3.1 General The following three types of test-site measurement g
37、round surface, described in 5.3.2, 5.3.3 and 5.3.4, are allowed: a) hard reflecting plane (concrete or non-porous asphalt); b) combination of hard reflecting plane and sand; c) all-sand plane. The hard reflecting plane, as described in 5.3.2, shall be used for testing the following: rubber-tyred mac
38、hines, all modes of operation; excavators, all modes of operation; crawler loaders, stationary hydraulic mode of operation; rollers, all modes of operation. The combination of hard reflecting plane and sand, as described in 5.3.3, may be used for rollers with raised pads and landfill compactors. The
39、 combination of hard reflecting plane and sand, as described in 5.3.3, or the all-sand plane, as described in 5.3.4, shall be used for crawler-type machines (e.g. crawler dozers, crawler loaders, crawler dumpers, etc.) in travel and stationary hydraulic modes, provided that the environmental correct
40、ion, K2A, determined in accordance with ISO 3744:, Annex A, is less than 2,0 dB, and for the all-sand plane, as described in 5.3.4, and where K2A is greater than 0,5 dB, the correction is accounted for in the calculation of the sound power level. 5.3.2 Hard reflecting plane The test area bordered by
41、 the vertical projection of the microphones to the ground shall consist of concrete or non-porous asphalt. 5.3.3 Combination of hard reflecting plane and sand The travel path of the machine shall consist of humid sand of grain size up to 2 mm. The minimum depth of the sand shall be 0,3 m. If 0,3 m i
42、s not deep enough for track penetration, the depth shall be increased accordingly. The ground surface between the machine and the microphones shall be a hard reflecting plane, as described in 5.3.2. It is possible to use a combination site of minimum size comprising only a single reflecting plane wi
43、th a sand path along the side. In this case, the machine shall be operated in a forward travel mode twice, each time in the opposite direction, for each of the three microphone positions. The reverse travel mode shall be carried out in the same manner. 5.3.4 All-sand plane The sand shall be as speci
44、fied in 5.3.3. -,-,- ISO 6395:2008(E) 4 ISO 2008 All rights reserved 5.4 Background noise correction, K1A The requirements for background noise, as specified in ISO 3744, shall be fulfilled. Corrections for background noise shall be made as specified in ISO 3744:, 8.3.2. 5.5 Climatic conditions Meas
45、urements shall not be carried out under the following conditions: a) when there is precipitation, i.e. rain, snow or hail; b) when the ground surface is covered with snow; c) when the temperature is below 10 C or above +35 C; d) when the wind speed exceeds 8 m/s; for wind speeds in excess of 1 m/s,
46、a microphone windscreen shall be used and appropriate compensation for the effect of its use allowed for when calibrating. 6 Measurement of time-averaged A-weighted sound pressure levels 6.1 Size of measurement surface The measurement surface to be used for the test shall be a hemisphere. The radius
47、 of the hemisphere shall be determined by the basic length, l, of the machine as specified in Annex A. The radius shall be 4 m when the basic length, l, of the machine to be tested is less than 1,5 m, 10 m when the basic length, l, of the machine to be tested is greater than or equal to 1,5 m but le
48、ss than 4 m, 16 m when the basic length, l, of the machine to be tested is greater than or equal to 4 m but less than 8 m, and the smallest radius of the sequence, 16 m, 18 m, 20 m. when the basic length, l, of the machine to be tested is greater than 8 m and the hemisphere radius exceeds twice the characteristic length, d0, of the machine to be tested. NOTE Characteristic length, d0, is as defined in ISO 3744, with the machine length, l, equal to l1. 6.2 Microphone positions on the hemispherical measureme