《ISO-6365-1-1988.pdf》由会员分享，可在线阅读，更多相关《ISO-6365-1-1988.pdf（6页珍藏版）》请在三一文库上搜索。
1、INTERNATIONAL STANDARD INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION MEXQYHAPOAHAR OPrAHkl3AMR n0 CTAHflAPTkl3AMM Wrought aluminium and aluminium alloy cold-drawn wire - Part 1 : Technical conditions for inspection and delivery Fils b) the metallurgical
2、temper of the material for delivery (degree of hardness or heat treatment condition) and, if dif- ferent, the metallurgical temper for use; c) the International Standard or specification number, or, where none exists, the test methods and properties agreed between the supplier and the purchaser; d)
3、the dimensions and shape of the product and/or reference to a drawing defining the product; e) tolerances on the dimensions and form, with reference to the appropriate International Standard; f) quantity; 1) To be published. 1 Copyright International Organization for Standardization Provided by IHS
4、under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 21:32:09 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6365-l : 1966 (E) g) any requirements for certificates of conformity, test and/or analysis; Unless otherwise agreed,
5、 the purchaser may only reject those products having dimensions not complying with the specified tolerances. h) any special requirements such as additional testing, marking, surface protection, packaging or inspection prior to delivery, agreed between the supplier and the purchaser and specified at
6、the inquiry stage. 6 Test procedures 5 Requirements 6.1 Sampling 5.1 Production and manufacturing processes 6.1.1 Specimens Unless otherwise specified in the order, the production and manufacturing processes shall be left to the discretion of the producer. Unless explicitly stated otherwise in the o
7、rder, no obligation shall be placed on the producer to use the same pro- cesses for subsequent and similar orders. The selection, identification and preparation of specimens for chemical analysis and for mechanical and physical testing shall be carried out in accordance with IS0 2142. Specimens shal
8、l be taken in the longitudinal direction. 5.2 Quality control 6.1.2 Number of specimens The supplier shall be responsible for the performance of all in- spection and tests required bv the relevant International Stan- dard, specification or order, prior to shipment of the product. If the purchaser wi
9、shes to inspect the product at the supplier s works, he shall notify the supplier at the time of placing the order. Unless otherwise specified, the minimum rate of sampling shall be as follows : - for products of diameter or thickness up to and in- eluding 10 mm, one specimen shall be taken for each
10、 lot of 500 kg or part thereof but no more than one specimen per original coil; 5.3 Chemical composition - for products of diameter or thickness greater than The chemical composition shall comply with the requirements specified in ISO/R 209. 10 mm up to and including 25 mm, one specimen shall be tak
11、en for each lot of 1 000 kg or part thereof but no more than one specimen per original coil. 5.4 Mechanical properties The mechanical properties shall be in conformity with those specified in IS0 6365-2 or those agreed upon between the sup- plier and the purchaser and stated on the order. In additio
12、n, not less than one test piece representing any one inspection lot, nor less than one test piece representing any one heat-treatment lot shall be taken. 6.1.3 Test pieces 5.5 Surface finish The unmachined wire shall be taken as the test piece. The products shall be free from defects detrimental to
13、their suitable and proper use. Whilst an operation designed to mask a fault is not permitted, the elimination of a superficial fault is permissible, provided that the dimensional tolerances continue to be observed. 6.1.4 Number of test pieces One test piece shall be taken from each specimen, 5.6 Dim
14、ension and form tolerances 6.2 Methods of test The dimension and form tolerances of products delivered shall be in conformity either with the requirements of the national standards when no International Standards exist on the sub- ject, or with the requirements agreed upon between the sup- plier and
15、 the purchaser and specified in the order. International Standards are in preparation; they will have the reference numbers indicated in table 1. 6.2.1 Chemical composition Methods of analysis shall be at the discretion of the supplier. In case of dispute concerning the chemical composition, referen
16、ce analysis shall be carried out by the methods specified in the relevant International Standards and the results obtained by these methods shall be accepted. Table 1 6.2.2 Mechanical and physical tests international Standard Product The tensile testing shall be carried out in accordance with IS0 66
17、92. IS0 6365-3 IS0 6365-4 General purpose wire Rivet wire If other mechanical or physical tests are required, these shall be agreed between the supplier and the purchaser. These tests 2 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Tech
18、nical Standards 1/9972545001 Not for Resale, 04/27/2007 21:32:09 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6365-l : 1988 (E) shall be carried out either in accordance with the existing Inter- national Standards or agreed upon by the supplier and the pur- chaser. 6
19、.2.3 Measurement of dimensions The dimensions shall be measured by means of measuring in- struments which are of the accuracy required by the dimen- sions and dimensional tolerances. All dimensions shall be checked at the ambient temperature of the workshop or laboratory, and, in case of dispute, at
20、 a temperature between 15 OC and 35 OC. the requirements of the relevant standards and the order. This document shall certify that, according to examinations and results of representative tests, the products for delivery are in conformity with the relevant standards and with the additional requireme
21、nts in the order, if any. 7.2 Quality control test report If requested by the purchaser on the order and after being agreed upon by the supplier, the latter shall provide a test report detailing the current production controls carried out on identical products made using the same method as the prod-
22、 ucts for delivery, but not necessarily on the products for delivery themselves. 6.2.4 Surface finish 7.3 Certificate of test Unless otherwise specified, examination of surface appearance shall be carried out, without the assistance of magnifying ap- paratus, on products before delivery. 6.3 Retests
23、 6.3.1 Mechanical properties If one of the test pieces first selected fails to meet the re- quirements for the mechanical tests, two further specimens shall be taken from the same lot, one being from the same unit of product from which the original specimen was taken, unless that unit of product has
24、 been withdrawn by the supplier. If both test pieces from these additional specimens meet the re- quirements, the lot which they represent shall be deemed to comply with the requirements of this part of IS0 6365. Should one test piece fail, the inspection lot shall be deemed not to comply with the r
25、equirements of this part of IS0 6365. 6.3.2 Other properties The retesting procedures shall be determined by consultation between the supplier and the purchaser. 7 Conformity with standards 7.1 Certificate of conformity If requested by the purchaser on the order, the supplier shall provide a certifi
26、cate indicating that the material complies with If required on the order, the supplier shall provide a certificate detailing the limits of chemic 4 composition and the results of prescribed mechanical tests. This document shall certify that tests have been carried out on specimens taken from among t
27、he products for delivery themselves. The delivery of such a certificate generally implies inspection tests on individual lots or production units. 8 Marking Marking of products is only undertaken when specified in the product standard or specification or agreed upon between the supplier and the purc
28、haser and stated on the order. This marking shall not adversely affect the final use of the product. 9 Packing Unless otherwise specified in International Standards relating to special products or specified in the order, the method of packing shall be determined by the supplier who shall take all su
29、itable precautions to ensure that, under the usual conditions of transportation, the products will be delivered in a condition suitable for use. 10 Arbitration tests In cases of dispute concerning conformity with the re- quirements of the material standard or specification cited on the order, testin
30、g should be carried out by an arbitrator chosen by mutual agreement between supplier and purchaser. The arbitrator s decision shall be final. 3 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resal
31、e, 04/27/2007 21:32:09 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6365-l : 1966 (E) UDC 669.71-124.2-426 : 656.77 Descriptors : wrought products, aluminium products, cold-drawn products, wire, specifications. Price based on 3 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 21:32:09 MDTNo reproduction or networking permitted without license from IHS -,-,-