《ISO-4301-2-1985.pdf》由会员分享,可在线阅读,更多相关《ISO-4301-2-1985.pdf(4页珍藏版)》请在三一文库上搜索。
1、International Standard ( 4301 I2 0 a 4 ai!bb ,NTERNAT,ONAC ORGANIZATION FOR STANDARDIZATtON*MEXtAYHAPOAHAR OPrAHH3AUMR fl0 CTAHAAPTbl3AUHH*ORGANlSATlON INTERNATIONACE OE NORMALlSATlON Lifting appliances - Classification - Part 2: Mobile cranes Appareils de levage - Classification - Partie 2: Grues m
2、obiles First edition - 1985-08-15 iii i UDC 621.873.2/.3 Ref. No. ISO4301/2-1985 (E) 7 ?! Descriptors : lifting equipment, cranes (hoists), classification. 5 Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical
3、 Standards 1/9972545001 Not for Resale, 04/25/2007 10:21:02 MDTNo reproduction or networking permitted without license from IHS -,-,- Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing In
4、ternational Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaiso
5、n with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the IS0 Council. They are approved in accordance with IS0 procedures requiring at least 75
6、% approval by the member bodies voting. International Standard IS0 4301/2 was prepared by Technical Committee ISO/TC 96, Cranes, lifting appliances and related equipment. 0 international Organization for Standardization, 1985 0 Printed initzerland Copyright International Organization for Standardiza
7、tion Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 10:21:02 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 4301/2-1985 (E) Lifting appliances - Classification - Part 2: Mobile cra
8、nes 0 Introduction This part of IS0 4301 is one of a series covering classification of cranes. Other parts in the series will be as follows: Part 1: General. NOTE - Part 1 will be a revision of the existing IS0 4301. Part 3: Tower cranes, Part 4: Portal and pedestal cranes. Part 5: Overhead travelli
9、ng and gantry cranes. 1 Scope and field of application This part of IS0 4301 establishes a classification of mobile cranes and related crane mechanisms based on the number of operating cycles to be carried out during the expected life of the mobile crane or mechanism and on a load spectrum factor wh
10、ich represents a nominal state of loading. It applies to basic types of self-propelled mobile cranes and their parts as defined in IS0 4306/2. 2 References IS0 4301, Lifting appliances - Classification. IS0 430612, Llictng appliances - Vocabulary - Part2: Mobile cranes. IS0 4308, Cranes - Selection
11、of wire ropes. 3 Classification The group classifications of a mobile crane and its mechanism are based on the operating (service) conditions given in table 1. Table I - Mobile crane group classification* Crane operating conditions Group Cranes for general hook duties, not used for continuous servic
12、e Al Crane equipped with bucket, grapple or magnet A3 Heavy duty, for example container handling or general dock service A4 * See also table 3 of IS0 4301, which gives the related series of Q (state of loading) and U (class of utilization) factors. 1 Copyright International Organization for Standard
13、ization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 10:21:02 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 4301/2-1995 (E) 4 Mechanism group classification The group classifications of mechanisms of
14、mobile cranes are shown in table 2. Table 2 - Mechanism group classification (see notes) Crane operating conditions Action Al A3 A4 Hoist M3 M4 M5 Slew M2 M3 M4 Luff M2 M3 M3 Telescope Ml M2 Ml* Travel fat work site only) : wheel mounted Ml Ml Ml crawler mounted Ml M2 M2 l The telescoping function i
15、s not performed with a suspended load. NOTES 1 See table 6 of IS0 4301. 2 For Ml, M2, M3, M4 and M5, the related series of L (state of loading) and T (class of utilization) factors as stated in table 6 of IS0 4301 apply. 3 The classifications presented do not relate to the Z, values for ropes and h
16、values for drum and sheave ratio. (See IS0 4308.1 2 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 10:21:02 MDTNo reproduction or networking permitted without license from IHS -,-,-