《ISO-7787-4-2002.pdf》由会员分享,可在线阅读,更多相关《ISO-7787-4-2002.pdf(28页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 7787-4:2002(E) ISO 2002 INTERNATIONAL STANDARD ISO 7787-4 First edition 2002-03-15 Dental rotary instruments Cutters Part 4: Miniature carbide laboratory cutters Instruments rotatifs dentaires Fraises techniques Partie 4: Fraises techniques miniatures en carbure pour laboratoir
2、e Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) PDF disclai
3、mer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties acc
4、ept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the
5、file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2002 All righ
6、ts reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the
7、 requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2002 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO
8、 Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) ISO 2002 All rights reserved iii Contents Page Foreword.iv Introduction.v 1 Scope1 2 Normative references1 3
9、 Symbols1 4 Requirements.2 4.1 Materials .2 4.2 Shapes2 4.3 Dimensions and number of blades2 4.4 Toothing19 4.5 Run-out.19 5 Test procedure.19 5.1 Shapes19 5.2 Dimensions and number of blades19 5.3 Toothing19 5.4 Run-out.19 6 Acceptance quality limit (AQL) 19 7 Designation of toothing and number of
10、blades19 8 Marking.20 9 Labelling on the package20 10 Packaging.20 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permit
11、ted without license from IHS -,-,- ISO 7787-4:2002(E) iv ISO 2002 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out th
12、rough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collab
13、orates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Stan
14、dards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of
15、 this part of ISO 7787 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7787-4 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 4, Dental instruments. ISO 7787 consists of the following parts, under th
16、e general title Dental rotary instruments Cutters: Part 1: Steel laboratory cutters Part 2: Carbide laboratory cutters Part 3: Carbide laboratory cutters for milling machines Part 4: Miniature carbide laboratory cutters Copyright International Organization for Standardization Provided by IHS under l
17、icense with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) ISO 2002 All rights reserved v Introduction This part of ISO 7787 is one of a series of stand
18、ards relating to dental rotary instruments. The various dimensional and other requirements specified for miniature carbide laboratory cutters are those considered important to ensure the interchangeability and safe usage of these instruments in the dental laboratory. The nominal diameters of the wor
19、king part listed in Tables 1 to 16 comply with the diameters specified in ISO 2157, Dental rotary instruments Nominal diameters and designation code number. Attention is drawn to ISO 6360, which specifies a 15-digit number coding system for the identification of dental rotary instruments of all type
20、s. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organ
21、ization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 7787-4:2002(E) ISO 2002 All rights
22、 reserved 1 Dental rotary instruments Cutters Part 4: Miniature carbide laboratory cutters 1 Scope This part of ISO 7787 specifies the shape and dimensional characteristics, number of blades, type of toothing and run-out for the ten most common miniature carbide laboratory cutters, which are predomi
23、nantly used in the dental laboratory. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 7787. For dated references, subsequent amendments to, or revisions of, any of these publications do not a
24、pply. However, parties to agreements based on this part of ISO 7787 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO
25、and IEC maintain registers of currently valid International Standards. ISO 1797-1, Dental rotary instruments Shanks Part 1: Shanks made of metals ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
26、ISO 6360-1, Dental rotary instruments Number coding system Part 1 General characteristics ISO 8325, Dental rotary instruments Test methods 3 Symbols For the purposes of this part of ISO 7787, the following symbols apply. d1 diameter of working part, head diameter; d2 neck diameter; l length of worki
27、ng part, head length; angle of working part. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license fr
28、om IHS -,-,- ISO 7787-4:2002(E) 2 ISO 2002 All rights reserved 4 Requirements 4.1 Materials 4.1.1 Working part The working part shall be made of tungsten carbide. The selection of the type of tungsten carbide and its treatment are at the discretion of the manufacturer. 4.1.2 Shank The material of th
29、e shank shall comply with ISO 1797-1. 4.2 Shapes The shapes of the working part shall be as specified in Figures 1 to 15. Variations of the shapes are permitted within the limited dimensions and the descriptions used in the subclause titles. Testing shall be carried out in accordance with 5.1. 4.3 D
30、imensions and number of blades 4.3.1 Working part 4.3.1.1 General Dimensions are given in millimetres and angles are given in degrees. The dimensions of the working part shall be as specified in Figures 1 to 15 as appropriate and Tables 1 to 15 as appropriate. The number of blades shall be as specif
31、ied in Table 16. Testing shall be carried out in accordance with 5.2. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking per
32、mitted without license from IHS -,-,- ISO 7787-4:2002(E) ISO 2002 All rights reserved 3 4.3.1.2 Spherical, round Figure 1 Table 1 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max. l 0,5 010 1,0 0,75 0,85 012 1,2 0,85 1,05 014 1,4 0,95 1,25 016 1,6 1,05 1,4 018 1,8 1,20 1,6 021
33、 2,1 1,35 1,9 023 2,3 1,45 2,1 025 2,5 1,50 2,3 027 2,7 1,60 2,5 031 3,1 1,80 2,6 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or ne
34、tworking permitted without license from IHS -,-,- ISO 7787-4:2002(E) 4 ISO 2002 All rights reserved 4.3.1.3 Inverted conical 4.3.1.3.1 Inverted conical, regular Figure 2 Table 2 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max. l 0,5 014 1,4 0,95 1,2 018 1,8 1,25 1,55 031 3,1
35、2,35 3,0 10 to 16 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:200
36、2(E) ISO 2002 All rights reserved 5 4.3.1.3.2 Inverted conical, long Figure 3 Table 3 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max. l 0,5 014 1,4 0,95 4,75 016 1,6 1,10 4,75 023 2,3 1,45 5,5 Copyright International Organization for Standardization Provided by IHS under lic
37、ense with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) 6 ISO 2002 All rights reserved 4.3.1.4 Cylindrical 4.3.1.4.1 Cylindrical, regular Figure 4 Tabl
38、e 4 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max. l 0,5 014 1,4 1,30 4,75 023 2,3 1,85 5,5 025 2,5 2,35 5,5 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for
39、 Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) ISO 2002 All rights reserved 7 4.3.1.4.2 Cylindrical, long Figure 5 Table 5 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max. l 0,5 023 2,3 2,35 15,0 Copyr
40、ight International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) 8 ISO 2002 All rig
41、hts reserved 4.3.1.5 Hemispherical, cylindrical 4.3.1.5.1 Hemispherical, cylindrical, regular Figure 6 Table 6 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max. l 0,5 014 1,4 1,30 4,75 023 2,3 1,85 5,5 Copyright International Organization for Standardization Provided by IHS un
42、der license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) ISO 2002 All rights reserved 9 4.3.1.5.2 Hemispherical, cylindrical, long Figure 7 Table
43、 7 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max. l 0,5 016 1,6 1,6 9,5 023 2,3 2,35 15,0 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007
44、 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) 10 ISO 2002 All rights reserved 4.3.1.6 Truncated conical, domed 4.3.1.6.1 Truncated conical, domed, regular Figure 8 Table 8 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max
45、. l 0,5 014 1,4 1,25 4,75 016 1,6 1,50 5,0 018 1,8 1,60 5,5 023 2,3 1,95 5,5 10 to 14 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction o
46、r networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) ISO 2002 All rights reserved 11 4.3.1.6.2 Truncated conical, domed, long Figure 9 Table 9 Dimensions Designation of nominal diameter (Nominal size) d1 0,1 d2 max. l 0,5 016 1,6 1,6 9,5 023 2,3 2,35 11,5 6 to 10 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Shell Global Solutions International B.V./5924979112 Not for Resale, 04/17/2007 10:53:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7787-4:2002(E) 12