《ISO-98-2001.pdf》由会员分享，可在线阅读，更多相关《ISO-98-2001.pdf（10页珍藏版）》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 98 Third edition 2001-03-01 Reference number ISO 98:2001(E) ISO 2001 Textile machinery and accessories Spinning preparatory and spinning machinery Main dimensions of coverings for top rollers Matriel pour lindustrie textile Matriel de prparation de filature et de filature
2、Dimensions principales des garnitures pour cylindres suprieurs Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:04 MDTNo reproduction or networking permitted without license
3、 from IHS -,-,- ISO 98:2001(E) ii ISO 2001 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on
4、the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used
5、 to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please in
6、form the Central Secretariat at the address given below. ISO 2001 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec- tronic or mechanical, including photocopying and microfilm, without permission in writing fr
7、om either ISO at the address below or ISOs mem- ber body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland Copyright International Organization for Standard
8、ization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:04 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 98:2001(E) ISO 2001 All rights reserved iii Foreword ISO (the International Organization for
9、 Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical com- mittees. Each member body interested in a subject for which a technical committee has been established has th
10、e right to be represented on that committee. International organizations, governmental and non-governmental, in liai- son with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Intern
11、ational Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the mem
12、ber bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 98 was prepared by Technical Comm
13、ittee ISO/TC 72,Textile machinery and machinery for dry-cleaning and industrial laundering, Subcommittee SC 1,Spinning preparatory, spinning, twisting and winding machinery and accessories. This third edition cancels and replaces the second edition (ISO 98:1977), which has been technically revised.
14、Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:04 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standa
15、rdization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:04 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 98:2001(E) ISO 2001 All rights reserved 1 Textile machinery and acce
16、ssories Spinning preparatory and spinning machinery Main dimensions of coverings for top rollers 1Scope This International Standard specifies the main dimensions of coverings for ready-for-use top rollers (synthetic cover- ings). It is applicable to spinning preparatory and spinning machinery. 2Symb
17、ols bare roller diameter diameter with covering (finished ground) width of covering saddle force Btype of execution of covering with rectangular sides (see Figure 1 and Figure 2) Ctype of execution of covering with beveled sides (see Figure 1 and Figure 2) Dtype of execution of covering with rounded
18、 sides (see Figure 1 and Figure 2) d1 d2 b F Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:04 MDTNo reproduction or networking permitted without license from IHS -,-,- IS
19、O 98:2001(E) 2 ISO 2001 All rights reserved 3Dimensions 3.1Single-boss top rollers The main dimensions of coverings for single-boss top rollers used for spinning preparatory machinery (e.g. draw- frames and comber), are given in Figure 1 and Tables 1, 2 and 3 (see Figure 2 for twin-boss top rollers)
20、. In the case of single-boss top rollers with removable bushings execution is similar to that shown in Figure 3. Figure 1 Diameters and covering widths for single-boss top rollers Table 1 Bare roller diameter Dimensions in millimetres 1618192326283035404550556065707580 NOTEFor, in increments of 10.
21、Table 2 Roller diameter with covering (finished ground) Dimensions in millimetres 25283234364045505560657075808590 NOTEFor, in increments of 10. Table 3 Width of covering Dimensions in millimetres 8090100110125140160180200220250280315355400450 d1 d180 d2 d290 b Copyright International Organization f
22、or Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:04 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 98:2001(E) ISO 2001 All rights reserved 3 3.2Twin-boss top rollers The main dimen
23、sions of coverings for twin-boss top rollers used for spinning and roving frames are given in Figure 2 and Tables 4, 5 and 6. In the case of twin-boss top rollers with removable bushings, execution is similar to that shown in Figure 3. Figure 2 Diameters and covering widths for twin-boss top rollers
24、 Table 4 Bare roller diameter Dimensions in millimetres 1923252830354045505560 NOTEFor, in increments of 10. Table 5 Roller diameter with covering (finished ground) Dimensions in millimetres 2528303235404550556065707580 NOTEFor, in increments of 5. Table 6 Width of covering Dimensions in millimetres
25、 2528303234354045505560 NOTEFor, in increments of 10. Figure 3 Covering fixed to a removable bushing d1 d160 d2 d280 b b 60 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:
26、04 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 98:2001(E) 4 ISO 2001 All rights reserved 4Designation of coverings The designation shall include a reference to this International Standard, followed by the dimensions,andex- pressed in millimetres, the Shore A hardnes
27、s, the type of execution and the saddle forceexpressed in decanew- tons. If no specification is given by the buyer, the manufacturer may supply any of the three executions, B, C or D. EXAMPLEA covering in accordance with ISO 98 of dimensions,and, a Shore A hard- ness of 80, of execution type B and a
28、 forcedecanewtons is designated as follows: ISO 98-28 ? ? ? ? 40 ? ? ? ? 160-80-B-40 d1d2b F d1=28 mmd2=40 mmb =160 mm F =40 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18
29、:04 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:04 MDTNo reproduction or networking permitted
30、without license from IHS -,-,- ISO 98:2001(E) ICS 59.120.10 Price based on 4 pages ISO 2001 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:18:04 MDTNo reproduction or networking permitted without license from IHS -,-,-