《ISO-8334-1985.pdf》由会员分享,可在线阅读,更多相关《ISO-8334-1985.pdf(3页珍藏版)》请在三一文库上搜索。
1、International Standard (! 8334 0 a 4 4JJiylim INTERNATIONAL ORGANIZATION FOR STANDARDlZATION*MEYHAPOHAR OPrAHH3AUHR fl0 CTAHAPT!43Al&lM.ORGANlSATlON INTERNATIONALE DE NORMALISATION Forestry machinery - Portable chain-saws - Determination of balance Matiriel forestier - Sties B chaine portatives - D&
2、termination de Iuquilibre First edition - 1965-10-15 UDC 621.936.6 : 634.036 Ref. No. ISO6334-1965 (E) Descriptors : agricultural machinery, forest equipment, portable equipment, saws, tests, determination, balancing. Price based on 1 page Copyright International Organization for Standardization Pro
3、vided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 09:22:42 MDTNo reproduction or networking permitted without license from IHS -,-,- Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national sta
4、ndards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International or
5、ganizations, govern- mental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the IS0 Council. They are approv
6、ed in accordance with IS0 procedures requiring at least 75 % approval by the member bodies voting. International Standard IS0 8334 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry. Users should note that all International Standards undergo revision f
7、rom time to time and that any reference made herein to any other International Standard implies its latest edition, unless otherwise stated. 0 international Organization for Standardization, 1985 0 Printed in Switzerland Copyright International Organization for Standardization Provided by IHS under
8、license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 09:22:42 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 8334-1985 (E) Forestry machinery - Portable chain-saws - Determination of balance 1 Scope and field
9、 of application This International Standard specifies a test method and requirements for the longitudinal balance of portable hand-held combustion engine chain-saws for use primarily in forestry. 2 Test method 2.1 The chain-saw fuel and oil tanks shall be half-full. The saw shall be fitted with guid
10、e-bars and chains within the dimensions recommended by the manufacturer. The test may be carried out with or without a spiked bumper. 2.2 The chain-saw shall be suspended from the front handle gripping area, a (see figure 11, at the point giving the best lateral balance, with the crankshaft horizont
11、al. 2.3 Measure the angle between the centreline of the guide-bar and the horizontal plane. (See clause 3.1 2.4 Chain-saws with an engine displacement of 82 cm3 or more which cannot meet the recommended angle requirement in clause 3 shall be positioned on a flat horizontal surface, standing steady o
12、n the base of the saw as shown in figure 2. With the saw thus, the guide-bar shall not touch the horizontal plane. Figure 1 - Handle gripping 3 Test requirements Figure 2 - Free-standing position of the saw In the interests of user safety and good ergonomics, the angle measured in 2.3 should not exceed 30”. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/25/2007 09:22:42 MDTNo reproduction or networking permitted without license from IHS -,-,-