《ISO-96-2-1992.pdf》由会员分享，可在线阅读，更多相关《ISO-96-2-1992.pdf（12页珍藏版）》请在三一文库上搜索。
1、INTERNATIONAL STANDARD 96-2 First edi tion 1992-01-15 Textile machinery and accessories - Rings and travellers for ring spinning and ring doubling frames - Part 2: HZCH-, HZ- and J-rings and their appropriate travellers Materiel pour Iindustrie textile - Anneaux et curseurs pour machines 5 #Zer et A
2、 retordre - Partie 2: Anneaux “HZCH”, WZ” et “J et leurs curseurs appropri 8; 9,5 6,3; 8; 9,5; 10,3; 11,l 16,7 25,4 38,l 9,l; 11,l 17,4 Inside diameter d 45 48 50 (51) 55 (57) 60 65 70 75 (76) 80 58 54,5 61 57,5 63 59,5 (64) (6095) 68 64,5 (70) (6675) 73 69,5 78 74,5 83 79,5 88 84,5 VW W75) 93 89,5
3、103 101 113 111 123 121 VW (126) 138 136 WV VW 153 151 163 161 (168) (166) 173 171 193 191 213 - 238 - 263 - NOTE -Values shown in parentheses are non-preferred. 90 100 110 VW 125 VW 140 150 (155) 160 - 180 200 225 250 Fitting diameter n, nom. - - - - - - - 74,5 79,5 84,5 (8595) 89,5 - - - - - - - -
4、 - 86 (87) 91 - - - - - - - - - - - - 101 101 111 111 121 121 (126) (126) 136 136 (138) (138) - 151 151 161 161 (166) (166) 171 171 - 123 (128) 138 (140) _- 153 163 VW 173 191 191 193 211 211 213 236 236 238 261 261 263 52,5 55,5 57,5 ww 62,5 (645) 67,5 72,5 77,5 82,5 (83,5) 87,5 - 97,5 107.5 117,5
5、- - - - - - - - - - - - - - T - - - - - - - 76 81 86 VW 91 101 111 121 VW 136 (138) 151 161 WV 171 191 - - - toi.) 0 - 0,25 0 -Cl,32 -c_p 0 - 0,4 -_-_I_ 0 -0,55 -e_I_ 1) The tolerante refers to the diameter A, excluding any ovality. 1 3 Copyright International Organization for Standardization Provid
6、ed by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 21:55:29 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9602:1992(E) 3 Travellers Examples of travellers appropriate for HZ-rings (and HZCH-rings) and J-rings are
7、 shown in figures 4 and 5 and figures 6 and 7 respectively. NOTE - HZ- and HZCH-rings are equipped with the same travellers. Figure 4 - Example of a metal traveller on an HZ-ring NOTE - HZ- and HZCH-rings are equipped with the same travellers. Figure 5 - Example of a plastics traveller on an HZ-ring
8、 sa- 1 - 1 , 1 . - I 3 il I xz . - Figure 6 - Exampie of a metal traveiler on a J-ring Figure 7 - Example of a plastics traveller on a J-ring Wire section descriptions and Symbols, and traveller Symbols and numbers are specified in table2. Traveller numbers are taken from the R20 series of preferred
9、 numbers in accordance with ISO 3111. The range of traveller numbers comprises values from 9 to 20 000 inclusive. The traveller number represents the nominal mass! in grams, of 1000 travellers of the Same type. The tolerante on the nominal mass for 1000 travel- lers of the Same type is + 3 % for met
10、al travellers and 0 % for plastics traGIlers. 4 Designation of travellers The designation of a traveller for an HZCH-, HZ- or J-ring shall include the following information in the Order given: a) “Traveller”; b) reference to this part of ISO 96 (i.e. ISO 96-2); c) the Symbol “HZ” or IJ”; d) the heig
11、ht h, in millimetres, of the appropriate ring; e) the manufacturers designation for the traveiler style (optional); f) the wire section Symbol (if applicable); g) the traveller material; h) the surface finish (optional); i) the appearance (optional); j) the traveller number. 4 Copyright Internationa
12、l Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 21:55:29 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9602:1992(E) EXAMPLES A traveller for an HZ-ring of height h = 16
13、,7 mm, in half-round steel wire, and of No. 400 is designated as follows: A travelier for a J-ring of height h = 11,l mm, in plastics, and of No. 100 is designated as follows: Traveller ISO 96-2 - J 11 ,l pIastics-100 Traveller ISO 96-2 - HZ 16,7 dr-steel-400 Table 2 - Travelter specifications metal
14、 Symbol Material , Wre section Number description Symbol (g per 1000 travellers) T 0 flat f 10 9 63 71 450 500 3150 3550 11,2 80 560 4000 HZ 0 round r 12,5 14 100 90 630 710 4500 5000 16 112 800 5600 L “ dr half -round 20 18 125 140 1000 900 6300 7 100 plastics - 0 round a 22,4 160 1120 8000 25 180
15、1250 9 000 31,5 28 200 224 1400 1600 10000 11200 metal 35,5 250 1800 12500 - , J 40 280 2000 14000 dr half -round 45 315 2240 16000 50 355 2500 18000 plastics - - 56 400 2800 20000 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical
16、 Standards 1/9972545001 Not for Resale, 04/23/2007 21:55:29 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 96-29 992(E) Annex A (informative) Bibliography l ISO 3:1973, Preferred numbers - Series of preferred numbers. 6 Copyright International Organization for Standard
17、ization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 21:55:29 MDTNo reproduction or networking permitted without license from IHS -,-,- This page intentionally left blank Copyright International Organization for Standardization Prov
18、ided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 21:55:29 MDTNo reproduction or networking permitted without license from IHS -,-,- This page intentionally leff blank Copyright International Organization for Standardization Provided by IHS
19、under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 21:55:29 MDTNo reproduction or networking permitted without license from IHS -,-,- This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under licens
20、e with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 21:55:29 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 96-2:1992(E) - UDC 677.0523 Descriptors: designation. textile machinery, spinnlng frames, ring spinning frames, ring twisters, t
21、ravellers, specifications, dimensions, Price based on 6 pages - Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 21:55:29 MDTNo reproduction or networking permitted without license from IHS -,-,-