《ISO-TR-15070-AMD-1-2005.pdf》由会员分享，可在线阅读，更多相关《ISO-TR-15070-AMD-1-2005.pdf（10页珍藏版）》请在三一文库上搜索。
1、TECHNICAL REPORT ISO/TR 15070 First edition AMENDMENT 1 1996-08-1 5 2005-05-01 Series I freight containers - Rationale for structural test criteria AMENDMENT 1 : Guidance on structural integrity Conteneurs de la srie 1 - Fondement des critres de rsistance AMENDEMENT 1: Lignes directrices pour lintgr
2、it de la structure Reference number ISO/TR 15070:1996/Amd.l:2005(E) 0 IS0 2005 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permitted without license
3、from IHS -,-,- ISO/TR 15070:1996/Amd.l:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer per
4、forming the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The IS0 Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the sofiware products used to create this
5、PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IS0 member bodies. In the unlikely event that a problem relating to it is found, please inform the Central
6、 Secretariat at the address given below. O IS02005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IS0 at
7、the address below or ISOs member body in the country of the requester. IS0 copyright office Case postale 56 CH-I211 Geneva 20 Tel. + 41 22 749 O 1 11 Fax +41 227490947 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii O IS0 2005 -All rights reserved Copyright International Organiza
8、tion for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 15070:1996/Amd.l:2005(E) Foreword IS0 (the International Organization for Standardization
9、) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repr
10、esented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (i EC) on all matters of electrotechnical standardization. International Standards a
11、re drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internatio
12、nal Standard requires approval by at least 75 % of the member bodies casting a vote. In exceptional circumstances, when a technical committee has collected data of a different kind from that which is normally published as an International Standard (“state of the art“, for example), it may decide by
13、a simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely informative in nature and does not have to be reviewed until the data it provides are considered to be no longer valid or useful. Attention is drawn to the possibility that some of the e
14、lements of this document may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISOTR 15070: 1996 was prepared by Technical Committee ISOTC 104, Freight containers, Subcommittee SC 1, General purpose containers. O IS0 2005
15、 -All rights reserved iii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization f
16、or Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 15070:1996/Amd.l:2005(E) Series I freight containers - Rationale for structural test criteria A
17、MENDMENT 1 : Guidance on structural integrity Page IO, 4.8.2.1 In the first line of the first paragraph, replace “the ability of the floor” with “the ability of the whole surface of the floor”. Page 13, affer the content Of 4.12.3 Add the following new text. 5 Prototype test criteria and sequence of
18、 tests 5.1 For 20 ft containers See Table 2. Table 2 - Prototype test criteria and sequence of tests for 20 ft containers Sequence of tests 1 2 2 . 1 2.2 3 3 . 1 3.2 3.3 Test a IS0 test number Dimensions check Floor strength: 8 7 260 kg Stacking: 3 8 1 6 kN 1 1,8R- T Dimensions check To confirm that
19、 all dimensions are in accordance with IS0 668: 1995 Bottom side rails Crossmem bers Corner post (horizontal dimensions) Bottom side rails Crossmem bers Maximum allowable residual deformation mm nla 3 4 2 3 3 O IS0 2005 -All rights reserved 1 Copyright International Organization for Standardization
20、Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 15070:1996/Amd.l:2005(E) Table 2 (continued) Dimensions check Maximum allowable residual deformation mm Sequence o
21、f IS0 test tests number Test a Lifting from top corner fittings: 2R- T 4 2 Bottom side rails Crossmem bers 3 3 Lifting from bottom corner fittings: 2R- T 5 3 5 . 1 I I Bottom side rails 3 5.2 I I Crossmembers 3 Lifting from fork-lift pockets: 1,6R - T 6 1 1 Bottom side rails Crossmem bers 3 3 4 71 R
22、estraint (longitudinal) Vertically Longitudinally 3 6 Rigidity (transverse) End frame b,c diagonally 10 Rigidity (longitudinal) Side frame at top fittings 6 End walls and doors Front end panel 7 10.2 I I Doors 6 6 I Strength of side walls Side panel 8 Strength of the roof 12.1 I 4 7 After testing, m
23、aximum allowable residual deformation for crossmem bers 15 rlOTE 1 rlOTE 2 All dimensions are in accordance with IS0 668:1995. After testing, no dimensions are allowed to be outside the planes of the corner-castings. Tis the tare of the container. Deformation should not affect security and door oper
24、ation. These values do not apply for one door off operation. ) ; 2 O IS0 2005 -All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permit
25、ted without license from IHS -,-,- ISO/TR 15070:1996/Amd.l:2005(E) 5.2 For 40 ft containers See Table 3. Table 3 - Prototype test criteria and sequence of tests for 40 ft containers Maximum allowable residual deformation Sequence of tests Dimensions check mm 1 To confirm that all dimensions are in a
26、ccordance with IS0 668: 1995 nla Dimensions check 2 Floor strength: 7 260 kg 2 . 1 Bottom side rails 3 2.2 Crossmem bers 4 2.3 Gooseneck 5 3 Stacking: 3 8 1 6 kN 3 . 1 Corner post (horizontal dimensions) 2 3.2 Bottom side rails 3 3.3 Crossmem bers 3 4 2 Lifting from top corner fittings: 2R - T 4.1 B
27、ottom side rails 3 4.2 Crossmem bers 3 5 3 Lifting from bottom corner fittings: 2R - T 5 . 1 Bottom side rails 3 5.2 Crossmem bers 3 6 1 1 Lifting from fork-lift pockets: 1,6R- T 6.1 Bottom side rails nla 6.2 Crossmem bers nla 7 Restraint 7 . 1 Vertically Longitudinally 4 7.2 10 O IS0 2005 -All righ
28、ts reserved 3 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 15070:1996/Amd.l:2005(E) Table 3 (continued
29、) Test a Dimensions check Sequence of IS0 test tests number I I I 8 9 I Rigidity (transverse) I 8.1 I I I End frame b,c diagonally 9 I 10 I Rigidity (longitudinal) I 9.1 I I I Side frame at top fittings 10 I 5 IEndwallsanddoors I 10.1 I I I Front end panel 10.2 I I I Doors 11 6 Strength of side wall
30、s 11.1 Side panel 12 7 strength of the roof 12.1 roof panel 14 I 13 I Waterproofness I all areas 15 After testing, maximum allowable residual deformation for crossmem bers Maximum allowable residual deformation mm 10 9 7 6 8 4 nla 6 NOTE 1 NOTE 2 All dimensions are in accordance with IS0 668:1995. A
31、fter testing, no dimensions are allowed to be outside the planes of the corner-castings. a Tis the tare of the container. Deformation should not affect security and door operation. These values do not apply for one door off operation. The container should allow no water ingress. Pages 13 and 14 Chan
32、ge the numbering of Clause5 and subclauses 5.1, 5.1.1, 5.1.2 and 5.2 to 6, 6.1, 6.1.1, 6.1.2 and 6.2, respectively. 4 O IS0 2005 -All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/20
33、09 19:07:17 MSTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permitted without l
34、icense from IHS -,-,- ISO/TR 15070:1996/Amd.l:2005(E) ICs 55.180.10 Price based on 4 pages O IS0 2005 -All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 03/04/2009 19:07:17 MSTNo reproduction or networking permitted without license from IHS -,-,-