《ISO-9190-1990.pdf》由会员分享,可在线阅读,更多相关《ISO-9190-1990.pdf(6页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 9190 First edition 1990-l 2-l 5 Lawn and garden ride-on (riding) tractors - Drawbar Tracfeurs de jardin et de pelouse A conducfeur porf6 - Barre d affelage Reference number IS0 9190:1990(E) Copyright International Organization for Standardization Provided by IHS under lice
2、nse with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 21:25:13 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 9190:1990(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards
3、 bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organiza
4、tions, govern- mental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are cir
5、culated to the member bodies for voting. Publication as an Inter- national Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 9190 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculfure and forestry. Annex A of t
6、his International Standard is for information only 0 IS0 1990 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Or
7、ganization for Standardization Case Postale 56 l CH-1211 Geneve 20 l Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 21:25:13 MDTNo reproduc
8、tion or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 9190:1990(E) Lawn and garden ride-on (riding) tractors - Drawbar 1 Scope This International Standard specifies the dimensions and location requirements for drawbars on lawn and garden ride-on (riding) tractors. It
9、 applies to lawn and garden ride-on (riding) trac- tors as defined below. The requirements specified are essential to ensure that all types of towed implements, designed for op- eration in conjunction with lawn and garden tractors, can be operated with all currently manufactured types of lawn and ga
10、rden tractors designed to pull such implements. 2 Definition For the purposes of this International Standard, the following definition applies. ride-on (riding) machine; lawn and garden tractor; turf (riding) tractor: Self-propelled machine on which an operator rides, designed primarily for cutting
11、grass and auxiliary garden work. The cutting means may be an integral part of the machine or sus- pended from or attached to the machine. ) 3 Dimensions The drawbar, both of the tractor itself see figure la) and of the implement see figure lb), shall be rectangular and shall have the dimensions give
12、n in figure 1 and table 1. 4 Location The drawbar shall be located on the longitudinal mid-plane of the tractor. 1) For the convenience of the user of this InternaConal Standard, this definition is repeated from IS0 5395:1990 (definition 1340). 1 Copyright International Organization for Standardizat
13、ion Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 21:25:13 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 9190:1990(E) a) Tractor drawbar b) Implement drawbar 1) The tongue end of the tractor drawbar sh
14、all clear a clevis 51 mm wide mounted on an implement through a max. 90 swing to either right or left of the tractor drawbar centreline or implement tongue interference with the tractor tyre, whichever occurs first. Figure 1 - Drawbar dimensions and location Table 1 - Dimensions Dimensions in millim
15、etres Symbol Measurement Dimension min. max. Drawbar hitch hole location 4 along tractor centrellne (dis- tance ahead of largest outside 100 diameter rear tyre) Drawbar height (distance from h GRP to top of drawbar with 180 230 largest rear tyre) 12 Clearance, relative to imple- ment drawbar 38 - r
16、Drawbar thickness - 20 b Implement drawbar clevis 38 -. opening n Drawbar hitch hole diameter 14 23 2 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 21:25:13 MDTNo reproduction
17、or networking permitted without license from IHS -,-,- IS0 9190:1990(E) Annex A (informative) Bibliography I IS0 5395:1990, Power lawn-mowers, lawn trac- tors, lawn and garden tractors, professional mowers, and lawn and garden tractors with mowing attachments - Definitions, safety re- quirements and
18、 test procedures. S IS0 9192:-*), Lawn and garden ride-on (riding) tractors - One-point tubular sleeve hifch. 4 IS0 9193:1990, Lawn and garden ride-on (rid- ing) tractors - Power take-off. 2 IS0 9191:21, Lawn and garden ride-on (riding) tractors - Three-point hitch. 2) To be published. Copyright Int
19、ernational Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 21:25:13 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 9190:1990(E) UDC 631.372:629.1 .013.8 Descriptors: agric
20、ultural machinery, horticultural machinery, power horticultural machinery, tractors, drawbars, dimensions. Price based on 3 pages - Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 21:25:13 MDTNo reproduction or networking permitted without license from IHS -,-,-