《ISO-TR-11762-1992.pdf》由会员分享，可在线阅读，更多相关《ISO-TR-11762-1992.pdf（7页珍藏版）》请在三一文库上搜索。
1、TECHNICAL REPORT IS0 TR 11762 First edition 1992-05-01 Light-gauge metal containers - Round open-top cans for liquid products with added gas - Classification of can sizes by construction type Emballages m4talliques lhgers - Boites rondes serties pour prod - type 2, when the subject is still under te
2、chnical development or where for any other reason there is the future but not immediate possibility of an agreement on an International Standard; - type 3, when a technical committee has collected data of a different kind from that which is normally published as an International Stan- dard (“state o
3、f the art”, for example). Technical Reports of types 1 and 2 are subject to review within three years of publication, to decide whether they can be transformed into International Standards. Technical Reports of type 3 do not necessarily have to be reviewed until the data they provide are considered
4、to be no longer valid or useful. ISO/TR 11762, which is a Technical Report of type 3, was prepared by Technical Committee ISO/TC 52, Light gauge metal containers. It gives, for information, a list of can sizes standardized in IS0 10654 but classified by construction type. NOTE - IS0 10654 specifies
5、only nominal filling volumes. 0 IS0 1992 All rlghts reserved. No part of thls publlcatlon may be reproduced or utlllzed In any form or by any means, electronic or mechanlcal, including photocopying and mlcrofllm, without permission in writing from the publisher. lnternatlonal Organization for Standa
6、rdlzation Case Postale 56 l CH-1211 Genkve 20 l Switzerland Printed In Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 04:13:33 MDTNo reproduction or networking pe
7、rmitted without license from IHS -,-,- ISOlTR 11762:1992(E) Together with IS0 10653, IS0 10654, ISO/TR 11761 and ISO/TR 11776, this first edition of ISO/TR 11762 cancels and replaces IS0 3004-1:1986, IS0 3004-2:1989, IS0 3004-3:1986, IS0 3004-4:1986, IS0 3004-5:1988 and IS0 3004-6:1986. Annex A of t
8、his Technical Report is for information only. It lists the can sizes previously standardized in IS0 3004-3:1986, sub-clause 3.1. ill Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/20
9、07 04:13:33 MDTNo reproduction or networking permitted without license from IHS -,-,- TECHNICAL REPORT ISO/TR 1176 - single necked-in cans ; - multiple necked-in cans. 2 References IS0 90-l Light gauge metal containers - Definitions and determination methods for dimensions and capacities - Part 1 :
10、Open-top cans. IS0 10654 Light gauge metal containers - Round open-top cans - Cans defined by their nominal filling volumes - Cans for liquid products with added gas. 3 Opening diameters (mm) Table 1 Straight-sided cans Straight-sided cans Single necked-in cans Single necked-in cans 53 53 50 50 65 6
11、5 63 63 65 65 63 63 Multiple necked-in cans Multiple necked-in cans 57 57 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 04:13:33 MDTNo reproduction or networking permitted with
12、out license from IHS -,-,- ISOlTR 11762:1992(E) 4 Classification by can type construction Open top cans - Round - 2 piece, necked-in Table 2 Nominal filling volume Nominal diameter N-4 (mm) 330 500 53,66 66 2 Copyright International Organization for Standardization Provided by IHS under license with
13、 ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 04:13:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISOlTR 11762:1992(E) ANNEX A Reference list The following can sizes were standardized in the former IS0 3004-3 Standard (Subclause 3.1) bu
14、t now these cans do not meet the required criteria to be standardized and incorporated in IS0 10654. Table A.1 - 73 - - 83 - - - 23( - - 60 - X - X . 68 - - - - - - - - - X - - - 99 200 250 275 296 330 355 375 473 500 750 1000 105 153 63 65 78 - 127 52 X - X - - - - - - - X - - - - X X X X - X 3 Cop
15、yright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 04:13:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISOlTR 11762:1992(E) UDC 621.798.1:672.46.001.33:6
16、63.64 + .86 Descriptors: packaging, metal packaging, food packaglng, beverages, sparkllng drinks, containers, cans, classlficatlon, size classlflcatlon. Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 04:13:33 MDTNo reproduction or networking permitted without license from IHS -,-,-