《ISO-96-1-2009.pdf》由会员分享，可在线阅读，更多相关《ISO-96-1-2009.pdf（10页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 96-1:2009(E) ISO 2009 INTERNATIONAL STANDARD ISO 96-1 Second edition 2009-03-01 Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Part 1: Flange rings T and SF and their travellers Matriel pour lindustrie textile Anneaux et curseu
2、rs pour machines filer et retordre Partie 1: Anneaux T et SF et leurs curseurs Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without lice
3、nse from IHS -,-,- ISO 96-1:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the
4、 editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file ca
5、n be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretaria
6、t at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing fr
7、om either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reserved Copyright Inter
8、national Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 96-1:2009(E) ISO 2009 All rights reserved iii Foreword ISO (the Interna
9、tional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has be
10、en established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stan
11、dardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies fo
12、r voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or al
13、l such patent rights. ISO 96-1 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories, Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories. This second edition cancels and replaces the first edition (ISO 96-1:1992), which has be
14、en technically revised. ISO 96 consists of the following parts, under the general title Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames: Part 1: Flange rings T and SF and their travellers Part 2: HZ- and J-rings and their travellers Copyright Interna
15、tional Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS unde
16、r license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 96-1:2009(E) ISO 2009 All rights reserved 1 Textile machinery and accessories Rings and travellers for ring sp
17、inning and ring twisting frames Part 1: Flange rings T and SF and their travellers 1 Scope This part of ISO 96 specifies the principal dimensions of T- and SF-rings, and the mass and tolerance on the mass, of the appropriate travellers for flange rings employed on ring spinning and ring twisting mac
18、hines. It also specifies the method of designation of the travellers. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced d
19、ocument (including any amendments) applies. ISO 3, Preferred numbers Series of preferred numbers 3 Principal dimensions of T- and SF-rings The principal dimensions of T- and SF-rings are illustrated in Figure 1 and Figure 2, and specified in Table 1. Figure 1 Example of a T-ring Copyright Internatio
20、nal Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 96-1:2009(E) 2 ISO 2009 All rights reserved Figure 2 Example of an SF-ring T
21、able 1 Ring dimensions Dimensions in millimetres T-ring SF-ring Inside diameter Height Fitting diameter Flange width Height Fitting diameter Flange width d1 b1 d2 b2 d h1 nominal tolerance a 0,15 0 + h2 nominal tolerance a 0,15 0 + 36 38 40 42 45 48 8 10 0 0,2 0 0,2 (50) 51 54 (55) 57 60 63 (65) 70
22、75 10 d + 7 0 0,25 2,6 b 3,2 c 4 d 10 12 d + 12 0 0,25 2,8 3,8 a The tolerance refers to the diameter d1, respectively d2, excluding any ovality. b The flange width b1 = 2,6 mm was designated previously as ring flange No. 1/2. c The flange width b1 = 3,2 mm was designated previously as ring flange N
23、o. 1. d The flange width b1 = 4 mm was designated previously as ring flange No. 2. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without
24、license from IHS -,-,- ISO 96-1:2009(E) ISO 2009 All rights reserved 3 4 Travellers 4.1 Examples of travellers appropriate for T- and SF-rings are shown in Figure 3 and Figure 4. Figure 3 Example of a traveller for a T-ring in the running position Figure 4 Example of a traveller for an SF-ring in th
25、e running position Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 96-1:2009(E) 4 ISO 2009 All rights re
26、served 4.2 The values for traveller mass are given in Table 2. Traveller mass is taken from the R20 series of preferred numbers in accordance with ISO 3. The range of traveller mass comprises values from 4 to 900 inclusive. The traveller mass represents the nominal mass, in grams, of 1 000 traveller
27、s of the same type. The tolerance on the nominal mass for 1 000 travellers of the same type is 3 %. Table 2 Traveller mass Mass of traveller (grams per 1 000 travellers) 4 25 160 4,5 28 180 5 31,5 200 5,6 35,5 224 6,3 40 250 7,1 45 280 8 50 315 9 56 355 10 63 400 11,2 71 450 12,5 80 500 14 90 560 16
28、 100 630 18 112 710 20 125 800 22,4 140 900 5 Designation of travellers The designation of a traveller for a T- and SF-ring shall include the following information: a) “Traveller ”; b) reference to this part of ISO 96 (i.e. ISO 96-1); c) the symbol “ T ” or “SF”; d) the flange width, b1, in millimet
29、res, of the appropriate ring; e) the manufacturers designation for the traveller style (e.g. “C”, “EL”); f) the wire section symbol (if applicable), e.g. “f ”, “r ” (“f” = flat, “r” = round); g) the traveller mass (see Table 2); h) the traveller material if it is other than steel (where this informa
30、tion is omitted, it is assumed that the traveller material is steel); i) the surface finish (optional); j) the appearance (optional). Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37
31、MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without license f
32、rom IHS -,-,- ISO 96-1:2009(E) ICS 59.120.10 Price based on 4 pages ISO 2009 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 04:58:37 MDTNo reproduction or networking permitted without license from IHS -,-,-