《JIS-A-6512-1992-R2004-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-A-6512-1992-R2004-ENG.pdf（22页珍藏版）》请在三一文库上搜索。
1、J I S A*b5L2 92 W 4933608 05LLL07 7T4 UDC 692.25-1 82 JIS JAPANESE INDUSTRIAL STANDARD Movable partitions JIS A 6512-1992 Translated and Published Japanese Standards Association 12 s Printed in Japan Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employee
2、s/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A%b552 92 V933bB8 0551508 b30 W In thc cvcnt of any doubt arising, the original Standard in Japrincsc is to be final authority. *- . I Copyright Japanes
3、e Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*b5L2 92 4933608 05LLL09 577 U JAPANESE INDUSTRIAL STANDARD Movable
4、partitions 1. Scope UDC 692.25-182 J I S A 6512-1992 This Japanese Industrial Standard specifies the movable partitions which are installed in the internal space of a building as the partitions of non-bearing walls, and are capable of being re-utilized by disassembling and assembling or shifting. Re
5、marks 1. As regards the accordion doors, sliding doors, toilet booths and screens, and the storage partitions which are added with the storage function to movable partitions, these are exempted from this Standard. 2. The standards cited in this Standard are given in Attached Table 1. 2. Types and sy
6、mbols The types and symbols of the movable partitions shall be as given in Table 1, according to the kinds of constructional styles and components. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/1
7、5/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*b5i12 72 D Li933608 05liL1i1iO 299 M 2 A 6512-1992 E Q, ci m rc1 I ; ; E m c) ci 9 2 u a, al ZOk 0, a h ci M Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS E
8、mployees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*b5iI2 92 m 4933608 05iIiIiIiIiI 125 m 3 A 6512-1992 % ! M “ 4 w s 5 s3uauoduroa 30 spulg FI .FI % .rl FI ; ; 1 a, o cd Ccl k 2 5 a, a s o d ! 2
9、 o a, a .rl G 3 a, I) O 5 9 s I) k a, P E a, E o I) cd P bn E : I) O a .FI *FI Q z 2 o cd a d .rl .FI k a E n 4 v I) a, c, Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo rep
10、roduction or networking permitted without license from IHS -,-,- J I S A*hCli! SI? = LiS33b08 0511112 Ob1 M 4 A 6512-1992 3. Qualities 3.1 The movable partitions shall be free from cambers, warps, torsions and other deformations harmful in use on profiles, and in addition, be free from defects conce
11、rning appearance, stains and the like on the surfaces. 3.2 The parts liable to be touched with human body or clothe shall be free from sharp protrusions and the like and be safe. 3.3 The painted surfaces shall be uniform in luster and tone of color, and be free from uneven painting, sagging, etc. 3.
12、4 The movable partitions, when tested in accordance with 6., shall conform to Table 2. Furthermore, as regards the noise insulation and fiame resistance, these shall be tested as required, and the results shall be appended. Table 2 Item Division Impact test by 1 kg in mass Impact test by 3 kg in mas
13、s Impact test by 50 kg in mass Transmission loss unit: dB Symbol Under 12 12 or over to and excl. 20 20 or over to and excl. 28 28 or over to and excl. 36 36 or over O 12 20 28 36 Perfor rnance There shall be no harmful cracking and peeling in use on surface. There shall be no ab- normalities of bre
14、aking and bending in internal construction, and there shall be no cracking and peeling on surface. There shall be no breaking and bending in composing members, and there shall be no harmful cracking and peeling in use on both surfaces. For each corresponding division, the noise in- sulation on the s
15、ound of 500 Hz shall conform to the prescribed value of transmission loss. Applicable test item 6.1.3 (1) 6.1.3 (2) 6.1.3 (3) 6.2 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MD
16、TNo reproduction or networking permitted without license from IHS -,-,- Item ing division, the flame resistance shall conform to the grade division of flame resistance. J I S A*b5L2 92 m 4933608 051LLL3 TT8 m 5 A 6512-1992 Table 2 (Contd) Division Symbol Flame resistance Grade 3 Flame resistance Gra
17、de 2 Flame resistance Grade 2 A Flame resistance Grade 1 0 4. Dimensions D C B A Performance Applicable test item 4.1 The modular nominal dimensions and symbols of the movable partitions shall be as given in Fig. 1. Copyright Japanese Standards Association Provided by IHS under license with JSALicen
18、see=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- 6 A 6512-1992 Fig. 1 - Composing member - reference plane - ceiling CO ,/-ordination plane Blow-out part i I In the case of using a stud In th
19、e case of having Type 0 I Floor co-ordination plane I W W L W + I K- : hlodular nominal dimension of width II,: I: : Ir;: II-: Nominal dimension of base board Modular nominal dimension of wainscot height modular nominal dimension of height of floor placing type modular nominal dimension of height 4.
20、1.1 The modular nominal dimensions of the widths of the movable partitions shall be the dimensions of Fig. 2, and the widths of product dimensions shall be the range of - 50 mm in respect to the modular nominal dimensions. Copyright Japanese Standards Association Provided by IHS under license with J
21、SALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- I t Type HI H Z Modular nominal dimensions of height HltoH3 1000 1500, 1800, 2100 Fig. II II ir N I r% C W 2 t-+- 7 A 6512-1992 Stud sy
22、stem Panel system Stud-panel system u u Unit: mm I 800, 900, 1200 Modular nominal dimensions of widths of movable partitions 4.1.2 The modular nominal dimensions of the heights of the movable partitions shall be the dimensions of Table 3 and Fig. 3, and the heights of products of the movable partiti
23、ons shall be in the range of f 30 mm in respect to the modular nominal dimensions in height. Table 3 Unit: mm 2300, 2400, 2500, 2600, 2700, 3000 H3 I Remarks: The nominal dimensions of heights of base boards for Ho shall be 60 mm, 75 mm and 100 mm. Copyright Japanese Standards Association Provided b
24、y IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*b5Li! 92 W i1933bOB 055LLl1b 707 W 8 A 6512-1992 Fig. 3 Ceiling co- ordination plane III o i I l l Fl
25、oor Co-ordination plane- 4.1.3 The modular nominal dimensions for widths and heights of the pillars of panels of the movable partitions shall be a6 given in Table 4, and the dimensions of depth of products shall be 2 5 mm in respect to the modular nominal dimensions of depth. Unit: mm Table 4 Modula
26、r nominal dimensions for depths of frames and pillars 1 25, 30, 40, 50, 60, 70, 80, 90, 100, 120 4.1.4 The modular nominal dimensions for widths and heights of the door sets shall be the dimensions of Table 5 and Fig. 4, and the product width of the door shall be within - 50 mm in respect to the mod
27、ular nominal dimension of width, and the product height of the door shall be in the range of 5 30 mm in respect to the modular nominal dimensions of height. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Res
28、ale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S As6512 92 4933608 0511117 643 Modular nominal dimensions of widths of door sets (wdj Table 5 Single swinging door 900 Door with minor door 1200 9 A 6512-1992 Unit: mm I Double swinging doors I 18
29、00 Modular nominal dimension of height of door set (Hdj I 2100 Remarks: W given herein shall mean the modular nominal dimension of the width (Wd) of the door set, Hd shall mean the modular nominal dimension of the height of the door set, and H means the modular nominal dimension of the height includ
30、ing transom. U Fig. 4 /Ceiling Co-ordination plane , LFloor Co-ordination plane 4.2 The manufacturing tolerances of the movable partitions shall be k 5 mm in respect to the product dimensions. 5. Materials The materials and accessories to be used in the main parts of the movable partitions shall be
31、those having the qualities equal to or superior to Table 6 or these, and be those performing respective functions and having sufficient strengths, as well as causing no contact corrosion or having been processed with anticorrosion treatment. Copyright Japanese Standards Association Provided by IHS u
32、nder license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*bLili2 32 I Li333b08 OLibbbi18 58T M 10 A 6512-1992 Table 6 3aterlals Steels I _ Stainless steels Aluminium
33、alloys Glass Standard JIS A 59n6 JIS A 39ni JIS A 5908 JIS A 3909 JIS A 3910 JAS of timber6 JAS of wood for fittings JAS of assemblies JAS of ordinary plywoods JAS of special plywoods JIS A h931 JIS A S5W JS A Y505 JIS A 9514 6. Tests 6.1 Impact test 6.1.1 Test body The test body shall include joint
34、 parts, and for that having a doorwy and openings other than the doorway, that has been executed under the condition where actually being isntailed including these shall be used. In this case, the width of the test body shall be 4.5 m cr over up to and including 6 m as given in Fig. 5. In addition,
35、it shall be that which has been connected at least 3 m or over of general panels (type NI in this. Fig. 5 3 m min. e 4 . 5 T T or over up to and including 6 m * - Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not f
36、or Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*b512 92 4933608 051LLL9 4Lb = 11 A 6512-1992 6.1.2 Impact bodies shall be the following three kinds. The impact bodies to be used for the impact tests (1) Impact body of 1 kg in mass (Imp
37、act body of hard substance) (3) It shall be the steel ball of 1000 k 10 g in mass and approximately 63.5 mm in diameter, and to which a ring bolt or the like letting a rope or a wire pass through shall be mounted. Note ( 3 ) Usually, a steel ball for ball bearing is used, and the mass of 1 kg shall
38、be that including the ring bolt. (2) Impact body of 3 kg in mass (Impact body of soft and small substance) (4) 100 mm in diameter of spherical rubber sheet being reinforced by canvas to approximately 1.5 mm in thickness as given in Fig. 6, which is filled with fine sands smaller than 2 mm in diamete
39、r and lead shots of approximately 3 mm in diameter. Note ( 4 ) It shall be 3000 rt30 g in mass and approximately The surface skin of the impact body shall be provided with holes on its upper part and bottom part. hole at the uppermost part shall be approximately 15 mm in diameter, and the hole at th
40、e lowermost part be approximately 5 mm in diameter. The To this impact body, the adjustable ring bolt of approximately 4 mm in diameter is inserted into the hole of the diameter of this upper one as given in Fig. 6, so that it shall be so constructed that the extending fitting being attached to the
41、ring bolt expands and contracts by the action of spring. The ring bolt shall be that of approximately 120 mm in length so that, when the impact body has become spherical in shape, it protrudes approximately 20 mm from the hole of approximately 5 mm in diameter. This protruding end part is received b
42、y the cap shaped flange of approximately 25 mm in diameter. This flange is allowed to contact closely to the surface of the impact body by the fastening nut. The impact body shall be 3000 I 3 0 g in mass including the mass of bolt and the like. Copyright Japanese Standards Association Provided by IH
43、S under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*bCiL? 92 4933608 05LLL20 L3B E 12 A 6512-1992 Fig. 6. Impact body of 3 kg in mass Unit: mm Ring bolt 44 E
44、xtending fitting Flange $25 Fastening nut $4 u i (3) Impact body of 50 kg in mass (Impact body of soft an large substance) (5) That has been sewn on a bag shape composed of canvas of 8 pieces as given in Fig. 7, of which the upper part and bottom part shall have been reinforced by leather pieces res
45、pectively. Next, the reinforced glass balls of approximately 3 mm in diameter shall be contained in this bag, 80 as to make up to 50 2 0.5 kg in mass, further a slinging fitting shall be attached to its upper end. Note ( The size of the impact body shall be allowed to become conical in shape being e
46、nveloped by the ball of 400 mm in diameter, when the reinforced glass balls have been filled, and its vertex shall be located at the position of 400 mm from the center of the ball. The bottom of the bag shall be reinforced by sewing the leather of circular shape of 120 mm in diameter on it. made tha
47、t the hole of 80 mm is left, and this opening part shall be reinforced by sewing on a leather to it. The top part of the bag shall be so Further, to this reinforcing leather the four slinging fittings of the same shape shall be attached. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 22:11:39 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*b512 72 4733608 0511121 074 M 13 A 6512-1992 Fig. 7.