《JIS-Z-3264-1998-R2004-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-Z-3264-1998-R2004-ENG.pdf（7页珍藏版）》请在三一文库上搜索。
1、STDOJIS Z 32b4-ENGL 1998 4733bi18 U5b11855 OTb JAPANESE INDUSTRIAL STANDARD (E3 JIS 2 3264: 1998 Copper phosphorus brazing filler metais July, 2000 ERRATA page 1, In the column “Symbol B“ of Table 1, Error: B-Cu93&P-645/ 800 Correct: B-C80AgP-645/800 Remarks: This erratum is for correcting the first
2、 edition of this Standard. Japanese Standards Association -7- Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 20:35:22 MSTNo reproduction or networking permitted without license from IHS -,
3、-,- STD-JIS 2 32b4-ENGL 1998 4933b08 0559932 038 W J IS JAPANESE INDUSTRIAL STANDARD Translated and Published by Ja pa nese Standards Association Copper phosphorus brazing filler metals ICs 25.160.50 Descriptors : phosphorus, copper alloys, brazing alloys, filler metal Reference number : JIS 2 3264
4、: 1998 (E) 4s Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 20:35:22 MSTNo reproduction or networking permitted without license from IHS -,-,- Z 3264 : 1998 Foreword This translation has
5、been made based on the original Japanese Industrial Standard revised by the Minister of International Trade and Industry through deliberations at Japanese Industrial Standards Committee in accordance with the Industrial Standardization Law. Consequently JIS Z 3264 : 1985 is replaced with JIS Z 3264
6、: 1998. Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties. The
7、 relevant Minister and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said technica
8、l properties. Date of Establishment: 1963-03-01 Date of Revision: 1998-05-20 Date of Public Notice in Official Gazette: 1998-05-20 Investigated by: Japanese Industrial Standards Committee Divisional Council on Welding JIS Z 3264 : 1998, First English edition published in 1999-12 Translated and publi
9、shed by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 1999 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or
10、 utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Berni
11、e Not for Resale, 03/10/2007 20:35:22 MSTNo reproduction or networking permitted without license from IHS -,-,- STDmJIS 2 3264-ENGL 1998 H 4733b08 0557734 900 m JAPANESE INDUSTRIAL STANDARD JIS Z 3264 : 19% Copper phosphorus brazing filler metals Introduction This Japanese Industrial Standard is the
12、 revised version of the JIS Z 3264 : 1985 Copper phosphorus brazing filler metals, after taking the contents of the second edition of IS0 3677 Filler metal for soft soldering, brazing and braze welding-Designation issued in 1992 into account. In addition to the items specified in the JIS, “Designati
13、on and Symbols” specified in IS0 3677 are adopted and coordinated without changing the technical contents. 1 Scope used for brazing, hereinafter referred to as “brazing filler metals”. This Japanese Industrial Standard specifies the copper phosphorus brazing filler metais 2 Normative references a pa
14、rt of this Standard. The latest versions of those standards shall be applied. The following standards are referred to in this Standard and constitute JIS H 0321 JIS Z 3900 JIS Z 3903 General rules for inspection of non-ferrous metal materials Methods for sampling o f precious brazing filler metals M
15、ethods for chemical analysis o f copper phosphorus brazing filler metals 3 Classification chemical composition as shown in Table 1. The brazing filler metals shall be classified into 6 classes on the basis of their Table 1 Classes I Class l Chemical composition (mass % 1 Temperature (ref.) “C 1 Note
16、 : (1 Symbol B is specified in IS0 3677 and the marking of brazing filler metals. (1 The other elements are Pb, Sn, Fe and etc. Brazing Temp. 790 to 930 735 to 845 720 to 815 690 to 790 705 to 815 730 to 815 4 Quality The quality of the brazing filler metals shall be as follows : a) The brazing fill
17、er metals shall be uniform in quality and free from harmful defects in use. b) The chemical composition of the brazing filler metals shall comply with Table 1, when tested in accordance with the method specified in 6. 5 Shape, dimension and tolerance a) The shapes of the brazing filler metals shall
18、be ribbon, wire, bar, granule, powder and preformed types b) The dimension and tolerance of the ribbon type brazing filler metais shall be as agreed between the c The tolerance on diameter of the wire and bar types brazing filler metals shall be &3% for 1. O mm The shape, dimension and tolerance sha
19、ll be as follows: and they are represented by R, W, B, P (for granule and powder) and F respectively. parties concerned with delivery. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 20:35:
20、22 MSTNo reproduction or networking permitted without license from IHS -,-,- STDOJIS Z 32b4-ENGL 1998 W 4933b08 0559935 847 2 Z 3264: 1999 -5.0 mm. Other than that range shall be as agreed between the parties concerned with delivery. The tolerance for the 1 O00 mm long bar type brazing filler metals
21、 shall be &O. 5% and other than that shall be as agreed between the parties concerned with delivery. The ribbon and wire types brazing filler metals could be delivered as a coil when agreed between the parties concerned with delivery. The sizes and tolerances of the granule and powder and the prefor
22、med types brazing filler metals shall be as agreed between the parties concerned with delivery. Chemical analysis test The chemical analysis test of the brazing filler metals shall be in accordance with JIS Z 3903. 7 Inspection The inspection shall be conducted as follows : a) The quality, shape and
23、 dimension of the brazing filler metals shall meet the requirements of 4 and 5 above. However, a part of the chemical analysis test may be omitted subject to the consent between the parties concerned with delivery. b) The other general matters shall be in accordance with JIS H 0321 and JIS Z 3900. 8
24、 Packaging tion and damage during transportation and storage. The brazing filler metals shall be packaged properly to prevent possible contamina- 9 Designation of products The products shall be designated according to the classes (sym- bols), shapes and dimensions (thickness and width for ribbon typ
25、e, diameter for wire type, diameter and length for bar type, and size for granule and powder types). The dimension of the preformed type shall be as agreed between the parties concerned with delivery. Example : For ribbon type BCuP-1-R 1.0 - and/or B-Cu95P-710/925-R 1.0 -5.0 I l T I I Shape, Thickne
26、ss, Width I Class, (mm) (mm) (mm) (mm) IT Class, Shape, Thickness, Width For wire type BCuP-I-W 1.2 and/or B-Cu95P-710/925-W 1.2 Ir T i T I Shape, Dia. Class, Class, Shape, Dia. (mm) (mm) For bar type BCuP-1-B 3.2 and/or B-Cu95P-710/925-B 3.2 -1000 I T T I I I I I-I Class, Shape, Dia., Length (mm) (
27、mm) (mm) (mm) For granule and powder type BCuP-1-P 63 and/or B-Cu95P-710/925-P 63 Class, Shape, Dia., Length TT Shape, Size I Class, Class, Shape, Size (pm) (pm) 10 Marking 10.1 Each package of the brazing filler metals shall be clearly marked with the following information : a) Class (to be marked
28、with symbol A and/or B) b) Shape and dimension c ) Mass (net mass) d) Manufacturing number e) Date of manufacture or its abbreviation f) Name of manufacturer or its abbreviation Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Win
29、g, Bernie Not for Resale, 03/10/2007 20:35:22 MSTNo reproduction or networking permitted without license from IHS -,-,- STD*JIS Z 3264-ENGL L998 W 4933b08 055993b 783 H 3 Z 3264: 1999 10.2 brazing filler metals. Each package shall be marked with caution against fume and others generating at the time
30、 of using Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 20:35:22 MSTNo reproduction or networking permitted without license from IHS -,-,- Errata for JIS (English editon) are printed in S
31、tandardizmion Journal, published monthly by the Japanese Standards Association, and also provided to subscribers of T I S (English edition) in Monthly Informarion. Errata will be provided upon request, please contact: Standardization Promotion Department, Japanese Standards Association 4-1-24, Akasa
32、ka, Minato-ku, Tokyo, 107-8440 JAPAN TEL. 03-3583-8002 FAX. 03-3583-0462 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 20:35:22 MSTNo reproduction or networking permitted without license from IHS -,-,-