《JIS-T-9111-2-2000-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-T-9111-2-2000-ENG.pdf(5页珍藏版)》请在三一文库上搜索。
1、a J IS JAPANESE I NDUSTRIAL STANDARD Translated and Published by Japanese Standards Association JIS T 9111-2:2000 (IS0 4074-2 : 1994) Rubber condoms- Part 2 : Determination of length a a ICs 11.200 Descriptors : contraceptive sheaths, latices, dimensional measurement Reference number : JIS T 9111-2
2、: 2000 (E) 3s Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:08:12 MSTNo reproduction or networking permitted without license from IHS -,-,- T 9111-2 : 2000 ( S U 4074-2 : 1994) Forewor
3、d This translation has been made based on the original Japanese Industrial Standard established by the Minister of International Trade and Industry and Minister of Health and Welfare through deliberations at the Japanese Industrial Standards Committee in accordance with the Industrial Standardizatio
4、n Law: JIS T 9111 Rubber condoms consists of the following parts. JIS T 9111-1 Rubber condoms-Part 1 :Requirements JIS T 9111-2 Rubber condoms-Part 2 : Determination of length JIS T 9111-3 Rubber condoms-Part 3 : Determination of width JIS T 9111-5 Rubber condoms-Part 5: Testing for holes-Water leak
5、 test JIS T 9111-6 Rubber condoms-Part 6 : Determination of bursting volume and pressure JIS T 9111-7 Rubber condoms-Part 7 : Oven conditioning JIS T 9111-9 Rubber condoms-Part 9 : Determination of tensile properties JIS T 9111-10 Rubber condoms-Part 10 : Packaging and labelling Date of Establishmen
6、t: 2000-09-29 Date of Public Notice in Official Gazette: 2000-09-29 Investigated by: Japanese Industrial Standards Committee Divisional Council on Medical and Safety JIS T 9111-2:2000, First English edition published in 2001-08 Translated and published by: Japanese Standards Association 4-1-24, Akas
7、aka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 2001 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or
8、 mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan a a Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:08:12 MSTNo repr
9、oduction or networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS T 9111-2 : 2000 (IS0 4074-2 : 1994) Rubber condoms- Part 2 : Determination of length Introduction This Japanese Industrial Standard has been prepared based on IS0 4074-2 Rubber condoms-Part 2 :Determinat
10、ion of length published in 1994 as the second edition without modifying the technical contents. 1 Scope This part of JIS T 9111 specifies a method of determining the length of rubber condoms. Remarks : The following standard is the corresponding International Standard to this Standard. IS0 4074-2 :
11、1994 Rubber condoms-Part 2 : Determination of length The symbols for indicating the degree of correspondence are IDT (identical), MOD (modified) and NEQ (not equivalent) as specified in ISO/IEC Guide 2 1. (IDTI 2 Principle Free hanging of the unrolled condom over a graduated mandrel and measurement
12、of its length, the reservoir excluded. 3 Equipment A mandrel with a scale divided into millimetres and having the di- mensions shown in Fig. 1, with the zero beginning at the rounded end. 4 Procedure 4.1 the package is to be torn. Tear the package and remove the condom. Move the condom inside the pa
13、ckage such that it is away from the area where In no circumstance use scissors or other sharp instruments to open the package. Unroll the condom, stretch it slightly several times but by no more than 20 mm NOTE : Lubricants may be removed and suitable powders may be added to avoid sticking. 4.2 to s
14、mooth out the wrinkles caused by the condom having been rolled up. 0 4.3 Put the condom over the mandrel and let it hang freely, stretched only by its own weight. 4.4 Note, to the nearest millimetre, the smallest value of the length of the condom that can be read on the scale outside the open end of
15、 the condom. 5 Test report The test report shall include at least the following information: a) b) identification of the sample, e.g. batch number; the length measured in accordance with 4.4; c) the date of the test. Copyright Japanese Standards Association Provided by IHS under license with JSALice
16、nsee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:08:12 MSTNo reproduction or networking permitted without license from IHS -,-,- 2. T 9111-2 2000 (IS0 4074-2 : 1994) 6 Condom disposal Condoms su e ,acted to this test may also be used for deter- mination of width but sha
17、ll be destroyed after testing. 1 R 12.5 k 0.5 Dimensions in millimetres DTES 1 2 The zero point of the measuring scale is on the top of the hemisphere. The measuring scale shall be marked in millimetres in the region of mea- surement. ir Fig. 1 Mandrel for determining length o f condom Copyright Jap
18、anese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:08:12 MSTNo reproduction or networking permitted without license from IHS -,-,- Errata for JS (English edition) are printed in Standardization Journal,
19、 published monthly by the Japanese Standards Association, and also provided to subscribers of J I S (English edition) in Monthly Information. Errata will be provided upon request, please contact: Standardization Promotion Department, Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN TEL. 03-3583-8002 FAX. 03-3583-0462 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:08:12 MSTNo reproduction or networking permitted without license from IHS -,-,-