JIS-Z-8500-2002-R2007-ENG.pdf

《JIS-Z-8500-2002-R2007-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-Z-8500-2002-R2007-ENG.pdf（72页珍藏版）》请在三一文库上搜索。

1、JIS JAPANESE INDUSTRIAL STANDARD Translated and Published by Japanese Standards Association Ergonomics-Basic human body measurements for technological design ICs 13.180 Reference number : JIS Z 8500 : 2002 (E) PROTECTED BY COPYRIGHT 37 s Z 8500 : 2002 Foreword This translation has been made based on

2、 the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by The Japan Ergonomics Society (JES)/the Japanese

3、Standards Association (JSA) with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article 14. Consequently JIS Z 8500 : 1994 is replaced with this Standard. In order to conform to the

4、International Standard, this revision has been prepared based on IS0 7250 : 1996 Ergonomics-Basic human body measurements for technological design. Date of Establishment: 1994-03-01 Date of Revision: 2002-01-20 Date of Public Notice in Official Gazette: 2002-01-21 Investigated by: Japanese Industria

5、l Standards Committee Standards Board Technical Committee on Consumer Life Products JIS Z 8500 : 2002, First English edition published in 2003-09 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the

6、 contents, the original JIS is to be the final authority. O JSA 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing f

7、rom the publisher. Printed in Japan PROTECTED BY COPYRIGHT Z 8500 : 2002 Contents Page Introduction . 1 2 2.1 2.2 3 4 4.1 4.2 4.3 4.4 Scope Definitions population group Anthropometric terms . Measuring points . Measuring conditions Clothing of subject Support surfaces Measuring tools Body symmetry 4

8、.4.1 The anthropometer 4.4.2 4.4.3 4.4.4 Other measuring tools 4.5 Further conditions . 4.6 Posture in measurement Sliding and spreading calipers A tape measure, measuring cube and rod . 5 Measuring items 5.1 Items on the head 5.1.1 Total head height . 5.1.2 5.1.3 5.1.4 Stomion to vertex height 5.1.

9、5 Face length 5.1.6 Head length 5.1.7 5.1.8 5.1.9 5.1.10 Head breadth 5.1.11 Bitragion breadth Tragion to vertex height . Ectocanthion to vertex height . Occiput to ectocanthion distance Occiput to stomion distance . Occiput to tragion distance 1 1 1 1 1 2 7 7 7 7 7 7 8 8 8 8 8 9 9 9 9 9 10 10 10 10

10、 11 11 11 11 PROTECTED BY COPYRIGHT -,-,- Z 8500 : 2002 5.1.12 Interpupillary breadth 5.1.13 Head circumference . 5.1.14 Sagittal arc . 5.1.15 Bitragion arc . Measurements taken while subject stands . 5.2.1 Body mass (weight) . 5.2.2 Stature (body height) 5.2.4 Cervicale height . 5.2.5 Shoulder heig

11、ht 5.2.6 Anterior axillary height 5.2.7 Radiale height 5.2.8 Radiale stylion height . 5.2.9 Dactylion height . 5.2.10 Elbow height . 5.2.11 Fist (grip axis) height . 5.2.12 Dactylion height, over head . Iliac spine height, standing . 5.2.15 Crotch height 5.2.16 Tibiale height . 5.2.18 Upper limb len

12、gth . 5.2.19 Upper arm length 5.2.20 Forearm length . 5.2.21 Shoulder-elbow length 5.2.22 Forearm-fingertip length 5.2.23 Elbow-grip length 5.2.24 Arm reach from back 5.2.25 Grip reach; forward reach 5.2.26 Wall-ectocanthion distance 5.2.27 Wall-acromion distance . 5.2.28 Wall-cervicale distance . 5

13、.2.29 Elbow-wrist length 5.2.30 Shoulder (biacromial) breadth . 5.2 5.2.3 Eye height . 5.2.13 5.2.14 Trochanterion height . 5,2.17 Span . 12 12 12 12 13 13 13 13 13 14 14 14 15 15 15 16 16 16 17 17 17 18 18 18 19 19 19 20 20 20 20 21 21 21 22 (ii) PROTECTED BY COPYRIGHT Z 8500 : 2002 5.2.31 Shoulder

14、 (bideltoid) breadth 5.2.32 Chest breadth. standing . 5.2.33 Maximum body breadth 5.2.34 Elbow-to-elbow breadth 5.2.35 Bicristal breadth 5.2.36 Hip breadth, standing . 5.2.37 Chest depth, standing . 5.2.38 Thorax depth at mesosternale . 5.2.39 Thorax depth at the nipple 5.2.40 Body depth, standing 5

15、.2.41 Neck circumference . 5.2.42 Chest circumference at mesosternale 5.2.43 Chest circumference 5.2.44 Waist circumference 52.45 Upper arm circumference . 5.2.46 Forearm circumference . 5.2.47 Wrist circumference 5.2.48 Thigh circumference 5.2.49 Calf circumference . 5.2.50 Ankle circumference 5.3

16、Measurements taken while subject sits 5.3.1 Sitting height (erect) . 5.3.2 Eye height, sitting . 5.3.3 Cervicale height, sitting . 5.3.4 Shoulder height, sitting 5.3.5 Elbow height, sitting 5.3.6 Trochanterion height, sitting . 5.3.8 Thigh height, sitting . 5.3.9 Knee height . 5.3.7 Thigh clearance

17、5.3.10 Lower leg length (popliteal height) 5.3.11 Sitting surface height . 5.3.12 Buttock-knee length 5.3.13 Buttock-popliteal length (seat depth) 5.3.14 Buttock-calf length, sitting 22 22 23 23 23 24 24 24 25 25 25 26 26 26 27 27 27 28 28 28 29 29 29 29 29 30 30 30 30 31 31 31 31 32 32 (iii) PROTEC

18、TED BY COPYRIGHT -,-,- Z 8500 : 2002 5.3.15 Buttock-trochanterion length. sitting 5.3.16 Buttock-abdomen depth, sitting 5.3.17 Hip breadth, sitting . 5.3.18 Abdominal depth, sitting 5.3.19 Lower limb length, sitting . 5.4 Measurements on hand and foot 5.4.1 Hand length 5.4.2 Palm length perpendicula

19、r . Maximum distance Finger I to V . 5.4.6 Hand breadth, diagonal 5.4.7 Hand breadth at metacarpals . 5.4.8 Maximum hand breadth . 5.4.9 Index finger breadth, proximal . 5.4.10 Index finger breadth, distal . 5.4.11 Hand thickness . 5.4.12 Grip diameter, inside 5.4.13 Grip diameter, outside 5.4.14 Ha

20、nd circumference . 5.4.15 Foot length 5.4.3 Index finger length 5.4.4 5.4.5 Bistyloid breadth . 5.4.16 Foot breadth, diagonal 5.4.17 Foot breadth . 5.4.18 Foot circumference 5.4.19 Sphyrion height 5.4.20 Sphyrion fibulare height 6 Joints . Attached Figure 1 Measuring items . Annex 1 (normative) Thig

21、h length and lower leg length . Annex 2 (informative) Comparison table between JIS and corresponding International Standard . 32 33 33 33 33 34 34 34 34 35 35 35 35 36 36 36 36 37 37 37 37 38 38 38 38 39 39 45 52 53 (iv) PROTECTED BY COPYRIGHT -,-,- JIS Z 8500 : 2002 JAPANESE INDUSTRIAL STANDARD Erg

22、onomics-Basic human body measurements for technological design Introduction This Japanese Industrial Standard has been prepared based on the first edition of IS0 7250 Ergonomics-Basic human body measurements for techno- logical design published in 1996 with modifying some technical contents. The por

23、tions underlined with dots in this Standard are the matters not included in the original International Standard. The list of modified contents is given in the Annex 2 (informative) together with the explanation. The well-being of people is greatly dependent on their geometrical relationship with var

24、ious factors such as clothing, places of work, transportation, homes and rec- reational activities. To ensure harmony between people and their environments, it is necessary to quantify the size and shape of people for optimization of the techno- logical design of the workplace and the home environme

25、nt. This Standard may be used in conjunction with national or international regula- tions or agreements to assure harmony in defining population groups. In its various applications, it is anticipated that the basic list will be supplemented by specific ad- ditional measurements. 1 Scope This Standar

26、d provides a description of anthropometric measurements which can be used as a basis for comparison of population groups. The basic list specified in this Standard is intended to serve as a guide for er- gonomists who are required to define population groups and apply their knowledge to the geometri

27、c design of the places where people work and live. This list is not intended to serve as a guide for how to take anthropometric mea- surements, but it gives information to the ergonomist and designer on the anatomi- cal and anthropometrical bases and principles of measurement which are applied in th

28、e solution of design tasks. The International Standard corresponding to this Standard is as fol- lows. Remarks : In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equiva

29、lent) ac- cording to ISO/IEC Guide 21. IS0 7250 : 1996 Ergonomics-Basic human body measurements for technological design (MOD) 2 Definitions For the purposes of this Standard, the following definitions apply: 2 . 1 tivity. population group Group of people having some common environment or ac- 2.2 An

30、thropometric terms _._._._ PROTECTED BY COPYRIGHT 2 2 8500 : 2002 midsagittal plane Vertical plane dividing the human body into right and left halves. sagittal plane All planes parallel to the midsagittal plane. midsagittal line Line at which the midsagittal plane crosses with the sur- face of the b

31、ody. frontal . plane Vertical plane perpendicular to the midsagittal plane which di- vides the body into the front and rear halves. distal Away from the main mass of the body. proximal Part of arms and legs nearest to the torso. radial Side of radius bone in the forearm (thumb side). ulnar Side of u

32、lna bone in the forearm (little finger side). tibial Side of tibial bone in the lower leg (big toe side). fibular ._. Side of fibula bone in the lower leg (little toe side). biceps femoris One of large muscle in the rear side of the thigh. deltoid muscle Large muscle on the lateral border of the upp

33、er arm in the shoulder region. gluteal fold Fold of the skin making a boundary between the buttocks and the rear surface of the thigh. grip axis Axis of the fist corresponding with the longitudinal axis of a rod held in the hand. lateral Towards the side of the body. medial Towards the midline of th

34、e body. Frankfurt plane Plane determined by three points of right and left tragions and left orbitale. 3 Measuring . points The points of anthropometric measurement are as given in Table 1 and Figure 1. Remarks : In order to make the measuring points in the Table 1 correspond to the figure of the hu

35、man body in the Figure 1, the number of the measuring points is shown in the Figure 1. PROTECTED BY COPYRIGHT -,-,- 3 Z 8500 : 2002 Table 1 Measuring points Measuring point Definition Figure to be referred English equivalnt (informative) The highest point of the head in the midsagittal plane. Fig. 1

36、 a ) , b) vertex TTYTEN KTTEN Fig. 1 a) opistocranion The point on the midsagittal line at the most distal position from the glabella. The point on the root above the tragus (protrusion in front and outside of the ear hole). - tragion Fig. 1 a) ZISYUTEN SOWTOTEN . The most exterior point on the occi

37、put. The left andright euryons are within the same frontal plane. Fig. 1 a) euryon NUKRE On the midsagittal line, the low- est touchable point of the occipi- tal bone between the nape muscles. Fig. 1 a) nuchale The most anterior point of the forehead between the brow ridges in the midsagittal line.

38、Fig. 1 a) glabella MIKENTEN BIANTEN The cross point of sewn up line between forehead bone and na- sal bone, with the midsagittal line. Fig, 1 a) sellion KOTEN . Fig. 1 a) stomion The point where the mouth opening (space surrounded by the upper and lower lips) is cut by the midsagittal line. The lowe

39、st point of lower edge of the chin on the midsagittal line. OTOGAITEN Fig, 1 a) gnathion GAIGANKAKUTEN . The point where the upper eye- lid joins with the lower eyelid at the corner of the eye. Fig. 1 a) ectocanthion The lowest point of the lower edge of the eye hole (the hole on the head bone where

40、 eye ball is kept). Fig. 1 a) orbitale GANKATEN KEITUITEN The tip of the spinous process (protuberance projecting from the rear side of each bone of which the spine consists) of 7th cervical vertebra. cervicale Fig. 1 b) PROTECTED BY COPYRIGHT -,-,- 4 Z 8500 : 2002 - No. - 13 - 14 - 15 - 16 - 17 18

41、Table 1 (continued) Measuring point Definition Figure to be referred English equivalnt (informative) The point on the union of the straight line linking the left and right 4th sternebrae (the joint between the sternum and the rib) and the midsagittal line on the front breast surface. Fig. 1 b) - mes

42、osternale KYKOTU- TYTEN The most exterior point of the outer edge of the hump of the scapula (the large flat and pro- trusive part of the end of the shelf like protuberance on the back side surface of the scapula). Fig. 1 b) acromion KENPOTEN ZENEKIKATEN anterior armpit point Fig. 1 b) Fig. 1 b) Fig

43、. 1 b) The lowest point on the part where the greater pectoral on the front edge of the armpit con- nects. The most exterior protrusion of the bicristal (height of the bone extending along the upper edge of the pelvis). The point on the lowest edge of the upper and front iliospinale (the protrusion

44、on the front edge of the bicristal). ROKIOTU: RYTEN iliocristale TYKYOKUTEN iliospinale anterius The point on the outside proxi- mal end of the radiale top (the disc-shaped part at the proximal end of the radius). Fig. 1 b) radiale TKOTUTEN . The point on the most distal end of the stylus of the rad

45、ius (the sharp pointed part of the distal end of the radius). Fig. 1 b), C) stylion The point on the most distal end of the stylus of the ulna (the thin part protruding from the bulge of the ulna). Fig. 1 b ) , C) stylion ulnare Of the condyle of the second metacarpus (the bulging part on the distal

46、 of the metacarpus), the point protruding most to the radius side. Fig. 1 c) metacarpale radiale TOSOKF:. TYSYUTEN . . . . . . . . . . . . . . . . . . . . . . . SXKUSQK.Y:. TYSYUTEN . . . . . . . . . . . . . . . . . . . . . . . Of the condyle of the fifth metac- arpus (the bulging part on the distal

47、 of the metacarpus), the point protruding most toward the ulna side. metacarpale ulnare Fig. 1 c) PROTECTED BY COPYRIGHT 5 Z 8500 : 2002 Table 1 (concluded) Measuring point Definition Figure to be referred English equivalnt (informative) The point on the proximal end of the proximal phalanx of finge

48、r on the back side of the hand. The phalangions being in every finger are called thumb to little finger phalangion. Of the top of the middle finger, the most distal point. Fig. 1 c) phalangion SISETUTEN Fig. 1 b), c) dactylion SISENTEN TENSITEN . The point on the highest edge of the great trochanter of the thighbone (the big protrusion on the upper and outer side of the thighbone). Fig. 1 b) trochanterion KEXKOTUTEN The highest (proximal) point on the anteromedial margin of the tibia (the bulging part on the upper and ins