《NASM20426-2009.pdf》由会员分享，可在线阅读，更多相关《NASM20426-2009.pdf（7页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA , INC 1000 WILSON BLVD. ARLINGTON, VA 22209 ISSUE DATE: AUGUST 1998 REVISION DATE: MARCH 10, 2009 FED. SUPPLY CLASS 5320 THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM
2、 THE LAST REVISION DATE. COPYRIGHT 2009 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NATIONAL AEROSPACE STANDARD THIRD ANGLE PROJECTION CUSTODIAN NATIONAL AEROSPACE STANDARDS COMMITTEE TITLE RIVET, SOLID, COUNTERSUNK 100 , PRECISION HEAD, ALUMINUM AND TITANIUM COLUMBIUM ALLO
3、Y NASM20426 SHEET 1 OF 7 CLASSIFICATION PART STANDARD REVISION 2 PROCUREMENT SPECIFICATION NASM5674 ? FORM 08-02 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AERO
4、SPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARKS RIGHTS. E B (f) LENGTH .010 C (APPROX MATERIAL FOR FULL HEAD) S (b) D (a) .020 MAX A (f)100 1/2 R .010
5、 MAX T (b) MATERIAL IDENTIFICATION MARKS AND MANUFACTURERS ID (SEE REQT 6) ON RIVET HEAD 1100 (A) PLAIN 5056 (B) RAISED CROSS 2117 (AD) DIMPLED .020 MAX 2024 (DD) RAISED DOUBLE DASH (INACTIVE) 2017 (D) RAISED TEAT (INACTIVE) (SEE REQT 7) 7050 (E) INDENTED RING (SEE REQT 5) 2219-T81 (K) INDENTED SQUA
6、RE (INACTIVE) 2219-T62 (J) INDENTED 45Cb (T) INDENTED MATERIAL IDENTIFICATION MARKS .030 MAX.030 MAX.030 MAX .030 MAX (SEE REQT 5) .050 MAX .030 MIN .070 MAX .040 MIN .030 MIN .050 MAX DIAMONDTRIANGLE TABLE I. RIVET DIMENSIONS A B C D E S T .004 REF +.003 RAD -.001 .114 .022 .094 .062 (1/16) +.004 .
7、016 .019 .179 .036 .141 .094 (3/32) -.002 .023 .029 .225 .042 .188 .125 (1/8) +.005 .031 .039 .286 .055 .234 .156 (5/32) -.002 .039 .049 .353 .070 .281 .187 (3/16) +.006 .047 .059 .415 .083 .328 .219 (7/32) -.003 .054 .069 +.008 .476 .095 .375 .250 (1/4) -.003 .062 .078 .564 .106 .469 .312 (5/16) +.
8、010 .078 .098 .694 .134 .562 .375 (3/8) -.004 .094 .117 (a) .001 INCH SHANK DIAMETER INCREASE PERMISSIBLE WITHIN .100 INCH OF BASE OF HEAD. (b) RIVETS MAY BE FURNISHED WITH PLAIN ENDS, OR CHAMFERED ENDS WITH A RADIUS TO THE “T“ DIMENSION OR A 20 CHAMFER TO THE “S“ DIMENSION. THE INITIAL RELEASE OF T
9、HIS DOCUMENT SUPERSEDES MS20426, REVISION L, PART NUMBERS REMAIN MS20426 -,-,- NATIONAL AEROSPACE STANDARD COPYRIGHT 2009 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED FORM 08-02 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. A
10、IA DOES NOT QUALIFY SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARKS RIGHTS. THIS
11、 DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST REVISION DATE. NASM20426 SHEET 2 REVISION 2 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA , INC 1000 WILSON BLVD. ARLINGTON, VA 22209 (c) A PROFILE VIEW OF LAND A
12、REA MAY VARY FROM A LINE PARALLEL WITH THE SHANK TO A CURVE THAT WILL FALL WITHIN THE LIMITS ALLOWED. (d) THE CONICAL SURFACE OF THE HEAD SHALL BE CONCENTRIC WITH THE SHANK OF THE RIVET WITHIN .005 (.010 FIM). (e) HEAD-COCKING ANGLE RELATIVE TO AXIS OF RIVET 1/2 MAX. (f) MAXIMUM HEAD DIAMETERS ARE T
13、O THEORETICAL SHARP CORNERS AS MEASURED BY PROJECTION. REQUIREMENTS: 1. MATERIAL: ALUMINUM 1100-F (UNS A91100) AND ALUMINUM ALLOYS 2017-T4 (UNS A92017), 2024-T4 (UNS A92024), 2117-T4 (UNS A92117), 2219-T62 (UNS A92219), 2219-T81 (UNS A922119), 5056-H32 (UNS A95056), 7050-T73 (UNS A97050) PER QQ-A-43
14、0 AND TITANIUM COLUMBIUM ALLOY 45Cb (UNS R58450) PER AMS4982. 2. FOR PART NUMBERS OF RIVET LENGTH NOT LISTED SHOW 1/16 INCREMENT REQUIRED. 3. ADDITIONAL 1/32 LENGTH INCREMENTS MAY BE OBTAINED BY ADDING -5 AFTER THE LAST DIGIT OR LETTER IN PART NUMBER. 4. EXAMPLE OF PART NUMBER: MS20426 AD 4 - 12 A -
15、5 = ALUMINUM ALLOY 2117-T4 RIVET, 1/8 DIA. (3/4 + 1/32) LONG, ANODIZE CLEAR. INDICATES ADDITIONAL 1/32 INCH INCREMENT IN LENGTH. NO CODE INDICATES CHEMICAL SURFACE TREATMENT PER MIL-DTL-5541, CLASS 1A, GOLD/YELLOW. “A“ INDICATES ANODIZE PER MIL-A-8625, TYPE II, CLASS 1, CLEAR. “D“ INDICATES ANODIZE
16、PER MIL-A-8625, TYPE II, CLASS 1, DICHROMATE SEAL. “F“ INDICATES OPTION OF ANY FINISH EXCEPT AS NOTED BELOW. “S“ INDICATES CHEMICAL SURFACE TREATMENT PER MIL-DTL-5541, CLASS 1A, CLEAR. “N“ INDICATES ANODIZE PER MIL-A-8625, TYPE II, CLASS 2. NOTE: FOR 1100 AL. CHEMICAL SURFACE TREATMENT PER MIL-DTL-5
17、541, CLASS 1A, GOLD/YELLOW (NO CODE). FOR 2024 AL. ANODIZE PER MIL-A-8625, TYPE II, CLASS 1, DICHROMATE SEAL OR CLEAR OR CLASS 2 WITH SPECIFIED COLOR (A, D, OR N CODE). FOR 2017, 2117, 2219, 5056 AND 7050 AL. CHEMICAL FINISH SURFACE TREATMENT PER MIL- DTL-5541, CLASS 1A, CLEAR OR GOLD/YELLOW (CLEAR
18、FILM SHALL BE USED ONLY WHEN AUTHORIZED) OR ANODIZE PER MIL-A-8625, TYPE II, CLASS 1 (CLEAR OR DICHROMATE SEAL) OR CLASS 2. FOR TITANIUM COLUMBIUM, NO FINISH REQUIRED. INDICATES LENGTH IN 1/16 OF AN INCH. INDICATES DIAMETER IN 1/32 OF AN INCH. “A“ INDICATES 1100-F ALUMINUM “AD“ INDICATES 2117-T4 AL.
19、 ALLOY “B“ INDICATES 5056-H32 AL. ALLOY “D“ INDICATES 2017-T4 AL. ALLOY (INACTIVE FOR NEW DESIGN) “DD“ INDICATES 2024-T4 AL. ALLOY (INACTIVE FOR NEW DESIGN) “K“ INDICATES 2219-T81 AL. ALLOY (INACTIVE FOR NEW DESIGN) “E“ INDICATES 7050-T73 AL. ALLOY “T“ INDICATES TITANIUM COLUMBIUM ALLOY 45Cb “J“ IND
20、ICATES 2219-T62 AL. ALLOY BASIC MS NUMBER ? ? ? ? NATIONAL AEROSPACE STANDARD COPYRIGHT 2009 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED FORM 08-02 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS
21、 OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARKS RIGHTS. THIS DRAWING SUPERSEDES ALL ANTEC
22、EDENT STANDARD DRAWINGS FOR THE SAME PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST REVISION DATE. NASM20426 SHEET 3 REVISION 2 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA , INC 1000 WILSON BLVD. ARLINGTON, VA 22209 5. OUTER DIAMETER OF INDENTED RING (7050 RIVETS) SHALL BE
23、 A MAXIMUM OF 75% OF RIVET SHANK DIAMETER. THE MAXIMUM DEPTH OF THE RING SHALL BE .010 INCH. INDENTED RING IS REQUIRED ON 7050 RIVETS MANUFACTURED AFTER 2 JULY 1990. 6. MANUFACTURERS IDENTIFICATION IS REQUIRED TO BE DEPRESSED ON RIVET HEADS WITH A SHANK DIAMETER .125 INCH AND LARGER MANUFACTURED AFT
24、ER 2 JULY 1990. 7. ALUMINUM ALLOY 2017-T4 RIVETS WITH 33 KSI MIN. UNDRIVEN SHEAR STRENGTHS ARE ACCEPTABLE UNTIL 2 JULY 1990. NOTES: 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .010. 2. INTERCHANGEABILITY RELATION WITH AN426 RIVETS: MS20426 RIVETS OF LIKE DASH NUMBER
25、S ARE UNIVERSALLY, FUNCTIONALLY, AND DIMENSIONABLY INTERCHANGEABLE. 3. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 4. REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTED IN THAT ISS
26、UE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS (DoDISS) SPECIFIED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. 5. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE
27、 PROCURED AND USED UNTIL STOCK IS DEPLETED. ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM 2017-T4 2024-T4 ALUMINUM 2219-T81 TITANIUM ALUMINUM 1100-F 2117-T4 5056-H32 INACTIVE INACTIVE 7050-T73 INACTIVE 45 Cb 2219-T62 LENGTH DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH
28、No. DASH No. 1/16 NOM DIA. A2-2 AD2-2 B2-2 D2-2 DD2-2 E2-2 K2-2 T2-2 J2-2 .125 A2-3 AD2-3 B2-3 D2-3 DD2-3 E2-3 K2-3 T2-3 J2-3 .1875 A2-4 AD2-4 B2-4 D2-4 DD2-4 E2-4 K2-4 T2-4 J2-4 .250 A2-5 AD2-5 B2-5 D2-5 DD2-5 E2-5 K2-5 T2-5 J2-5 .3125 A2-6 AD2-6 B2-6 D2-6 DD2-6 E2-6 K2-6 T2-6 J2-6 .375 A2-7 AD2-7
29、B2-7 D2-7 DD2-7 E2-7 K2-7 T2-7 J2-7 .4375 A2-8 AD2-8 B2-8 D2-8 DD2-8 E2-8 K2-8 T2-8 J2-8 .500 A2-9 AD2-9 B2-9 D2-9 DD2-9 E2-9 K2-9 T2-9 J2-9 .5625 A2-10 AD2-10 B2-10 D2-10 DD2-10 E2-10 K2-10 T2-10 J2-10 .625 ? -,-,- NATIONAL AEROSPACE STANDARD COPYRIGHT 2009 AEROSPACE INDUSTRIES ASSOCIATION OF AMERI
30、CA, INC. ALL RIGHTS RESERVED FORM 08-02 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE
31、SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARKS RIGHTS. THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST REVISION DATE. NASM2042
32、6 SHEET 4 REVISION 2 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA , INC 1000 WILSON BLVD. ARLINGTON, VA 22209 ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM 2017-T4 2024-T4 ALUMINUM 2219-T81 TITANIUM ALUMINUM 1100-F 2117-T4 5056-H32 INACTIVE INACTIVE 7050-T73 INACTIVE 45 Cb 2219-T62 LENGTH DAS
33、H No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. 3/32 NOM DIA. A3-2 AD3-2 B3-2 D3-2 DD3-2 E3-2 K3-2 T3-2 J3-2 .125 A3-3 AD3-3 B3-3 D3-3 DD3-3 E3-3 K3-3 T3-3 J3-3 .1875 A3-4 AD3-4 B3-4 D3-4 DD3-4 E3-4 K3-4 T3-4 J3-4 .250 A3-5 AD3-5 B3-5 D3-5 DD3-5 E3-5 K3-5 T3-5 J3-5 .312
34、5 A3-6 AD3-6 B3-6 D3-6 DD3-6 E3-6 K3-6 T3-6 J3-6 .375 A3-7 AD3-7 B3-7 D3-7 DD3-7 E3-7 K3-7 T3-7 J3-7 .4375 A3-8 AD3-8 B3-8 D3-8 DD3-8 E3-8 K3-8 T3-8 J3-8 .500 A3-9 AD3-9 B3-9 D3-9 DD3-9 E3-9 K3-9 T3-9 J3-9 .5625 A3-10 AD3-10 B3-10 D3-10 DD3-10 E3-10 K3-10 T3-10 J3-10 .625 A3-12 AD3-12 B3-12 D3-12 DD
35、3-12 E3-12 K3-12 T3-12 J3-12 .750 A3-14 AD3-14 B3-14 D3-14 DD3-14 E3-14 K3-14 T3-14 J3-14 .875 A3-16 AD3-16 B3-16 D3-16 DD3-16 E3-16 K3-16 T3-16 J3-16 1.000 A3-20 AD3-20 B3-20 D3-20 DD3-20 E3-20 K3-20 T3-20 J3-20 1.250 AD3-32 2.000 ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM 2017-T4 2024-T
36、4 ALUMINUM 2219-T81 TITANIUM ALUMINUM 1100-F 2117-T4 5056-H32 INACTIVE INACTIVE 7050-T73 INACTIVE 45 Cb 2219-T62 LENGTH DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. 1/8 NOM DIA. A4-3 AD4-3 B4-3 D4-3 DD4-3 E4-3 K4-3 T4-3 J4-3 .1875 A4-4 AD4-4 B4-4 D4-4 DD4-4 E4-4 K
37、4-4 T4-4 J4-4 .250 A4-5 AD4-5 B4-5 D4-5 DD4-5 E4-5 K4-5 T4-5 J4-5 .3125 A4-6 AD4-6 B4-6 D4-6 DD4-6 E4-6 K4-6 T4-6 J4-6 .375 A4-7 AD4-7 B4-7 D4-7 DD4-7 E4-7 K4-7 T4-7 J4-7 .4375 A4-8 AD4-8 B4-8 D4-8 DD4-8 E4-8 K4-8 T4-8 J4-8 .500 A4-9 AD4-9 B4-9 D4-9 DD4-9 E4-9 K4-9 T4-9 J4-9 .5625 A4-10 AD4-10 B4-10
38、 D4-10 DD4-10 E4-10 K4-10 T4-10 J4-10 .625 A4-12 AD4-12 B4-12 D4-12 DD4-12 E4-12 K4-12 T4-12 J4-12 .750 A4-13 AD4-13 B4-13 D4-13 DD4-13 E4-13 K4-13 T4-13 J4-13 .8125 A4-14 AD4-14 B4-14 D4-14 DD4-14 E4-14 K4-14 T4-14 J4-14 .875 A4-16 AD4-16 B4-16 D4-16 DD4-16 E4-16 K4-16 T4-16 J4-16 1.000 A4-18 AD4-1
39、8 B4-18 D4-18 DD4-18 E4-18 K4-18 T4-18 J4-18 1.125 A4-20 AD4-20 B4-20 D4-20 DD4-20 E4-20 K4-20 T4-20 J4-20 1.250 A4-22 AD4-22 B4-22 D4-22 DD4-22 E4-22 K4-22 T4-22 J4-22 1.375 A4-24 AD4-24 B4-24 D4-24 DD4-24 E4-24 K4-24 T4-24 J4-24 1.500 A4-28 AD4-28 B4-28 D4-28 DD4-28 E4-28 K4-28 T4-28 J4-28 1.750 -
40、,-,- NATIONAL AEROSPACE STANDARD COPYRIGHT 2009 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED FORM 08-02 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UND
41、ER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARKS RIGHTS. THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME PRODUCT
42、AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST REVISION DATE. NASM20426 SHEET 5 REVISION 2 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA , INC 1000 WILSON BLVD. ARLINGTON, VA 22209 ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM 2017-T4 2024-T4 ALUMINUM 2219-T81 TITANIUM ALUMI
43、NUM 1100-F 2117-T4 5056-H32 INACTIVE INACTIVE 7050-T73 INACTIVE 45 Cb 2219-T62 LENGTH DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. 5/32 NOM DIA. A5-4 AD5-4 B5-4 D5-4 DD5-4 E5-4 K5-4 T5-4 J5-4 .250 A5-5 AD5-5 B5-5 D5-5 DD5-5 E5-5 K5-5 T5-5 J5-5 .3125 A5-6 AD5-6 B5-
44、6 D5-6 DD5-6 E5-6 K5-6 T5-6 J5-6 .375 A5-7 AD5-7 B5-7 D5-7 DD5-7 E5-7 K5-7 T5-7 J5-7 .4375 A5-8 AD5-8 B5-8 D5-8 DD5-8 E5-8 K5-8 T5-8 J5-8 .500 A5-9 AD5-9 B5-9 D5-9 DD5-9 E5-9 K5-9 T5-9 J5-9 .5625 A5-10 AD5-10 B5-10 D5-10 DD5-10 E5-10 K5-10 T5-10 J5-10 .625 A5-11 AD5-11 - - - - - - - .6875 A5-12 AD5-
45、12 B5-12 D5-12 DD5-12 E5-12 K5-12 T5-12 J5-12 .750 A5-14 AD5-14 B5-14 D5-14 DD5-14 E5-14 K5-14 T5-14 J5-14 .875 A5-16 AD5-16 B5-16 D5-16 DD5-16 E5-16 K5-16 T5-16 J5-16 1.00 A5-18 AD5-18 B5-18 D5-18 DD5-18 E5-18 K5-18 T5-18 J5-18 1.125 A5-20 AD5-20 B5-20 D5-20 DD5-20 E5-20 K5-20 T5-20 J5-20 1.250 A5-
46、22 AD5-22 B5-22 D5-22 DD5-22 E5-22 K5-22 T5-22 J5-22 1.375 A5-24 AD5-24 B5-24 D5-24 DD5-24 E5-24 K5-24 T5-24 J5-24 1.500 A5-28 AD5-28 B5-28 D5-28 DD5-28 E5-28 K5-28 T5-28 J5-28 1.750 A5-32 AD5-32 B5-32 D5-32 DD5-32 E5-32 K5-32 T5-32 J5-32 2.00 ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM 20
47、17-T4 2024-T4 ALUMINUM 2219-T81 TITANIUM ALUMINUM 1100-F 2117-T4 5056-H32 INACTIVE INACTIVE 7050-T73 INACTIVE 45 Cb 2219-T62 LENGTH DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. DASH No. 3/16 NOM DIA. A6-5 AD6-5 B6-5 D6-5 DD6-5 E6-5 K6-5 T6-5 J6-5 .3125 A6-6 AD6-6 B6-6 D6-6
48、 DD6-6 E6-6 K6-6 T6-6 J6-6 .375 A6-7 AD6-7 B6-7 D6-7 DD6-7 E6-7 K6-7 T6-7 J6-7 .4375 A6-8 AD6-8 B6-8 D6-8 DD6-8 E6-8 K6-8 T6-8 J6-8 .500 A6-9 AD6-9 B6-9 D6-9 DD6-9 E6-9 K6-9 T6-9 J6-9 .5625 A6-10 AD6-10 B6-10 D6-10 DD6-10 E6-10 K6-10 T6-10 J6-10 .625 - AD6-11 - - - - - - - .6875 A6-12 AD6-12 B6-12 D
49、6-12 DD6-12 E6-12 K6-12 T6-12 J6-12 .750 A6-14 AD6-14 B6-14 D6-14 DD6-14 E6-14 K6-14 T6-14 J6-14 .875 A6-15 AD6-15 B6-15 D6-15 DD6-15 E6-15 K6-15 T6-15 J6-15 .9375 A6-16 AD6-16 B6-16 D6-16 DD6-16 E6-16 K6-16 T6-16 J6-16 1.00 A6-18 AD6-18 B6-18 D6-18 DD6-18 E6-18 K6-18 T6-18 J6-18 1.125 A6-20 AD6-20 B6-20 D6-20 DD6-20 E6-20 K6-20 T6-20 J6-20 1.250 A6-22 A