《MIL-STD-290F-2000 4.28.pdf》由会员分享，可在线阅读，更多相关《MIL-STD-290F-2000 4.28.pdf（44页珍藏版）》请在三一文库上搜索。
1、AMSC N/A FSC PACK INCH-POUND MIL-STD-290F 17 July 2000 SUPERSEDING MIL-STD-290E 1 May 1981 DEPARTMENT OF DEFENSE STANDARD PRACTICE PACKAGING AND MARKING OF PETROLEUM AND RELATED PRODUCTS MIL-STD-290F ii THIS PAGE IS INTENTIONALLY LEFT BLANK MIL-STD-290F iii FOREWORD 1. This standard is approved for
2、use by all Departments and Agencies of the Department of Defense. 2. This standard should be used in conjunction with DLAI 4145.3/AFJMAN 24-204, “Preparing Hazardous Material for Military Air Shipments“, Code of Federal Regulations, Parts 100-180 of Title 49, Title 29, and any other applicable law o
3、r regulation required for the safe handling, storage, and transportation of material covered under this standard. 3. Beneficial comments (recommendations, additions, deletions) and any pertinent data that may be of use in improving this document should be addressed to: Defense Supply Center Richmond
4、, DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. MIL-STD-290F iv CONTENTS PARAGRAPH PAGE 1. SCOPE 1 1.1 Scope 1 1.2 Application. 1 1.2.1 Centr
5、ally procured items 1 1.2.2 Locally procured items . 1 1.3 Options . 1 2. APPLICABLE DOCUMENTS 1 2.1 General. 1 2.2 Government documents 1 2.2.1 Specifications and standards. 1 2.2.2 Other government publications 3 2.3 Non-government publications 3 2.4 Order of precedence . 4 3. DEFINITIONS. 5 3.1 C
6、ommercial packaging. 5 3.2 Containers. 5 3.3 Unit pack 5 3.4 Exterior pack 5 3.5 Intermediate pack . 5 3.6 Level of protection. 5 3.7 Marking 5 3.8 Shelf life items 5 3.8.1 Type I shelf life items. 5 3.8.2 Type II shelf life items . 5 4. GENERAL REQUIREMENTS 6 4.1 Unit containers 6 4.2 Coating of me
7、tal containers 6 4.3 Packing. 6 4.4 Marking 6 4.4.1 Bar code marking . 6 4.5 Palletization 6 4.6 Department of Transportation regulations 6 4.7 Reclaimed materials . 6 MIL-STD-290F v CONTENTS PARAGRAPH PAGE 5. DETAILED REQUIREMENTS 7 5.1 Packing products in unit containers 7 5.1.1 Unit pack 7 5.1.2
8、Intermediate pack . 7 5.1.3 Exterior pack 7 5.1.3.1 Level B intermediate packs of filled containers of less than 1-pint capacity 7 5.1.3.2 Level B intermediate packs of filled containers of 1-pint capacity and over 7 5.1.3.3 Level C intermediate packs of filled containers of less than 1-pint capacit
9、y 7 5.1.3.3.1 Filled cans of 1-pint capacity and over. 7 5.2 Packing standard grease cartridges (for cartridge-type grease guns) 8 5.2.1 Unit packing. 8 5.2.2 Intermediate packing 8 5.2.3 Exterior packing. 8 5.2.4 Level B. 8 5.2.5 Level C . 8 5.2.6 Commercial level 8 5.3 Packing products in drums .
10、8 5.3.1 Palletization 8 5.3.1.1 Arrangement of drums on pallets. 8 5.3.1.2 Unitization loads for DoD and other Government agencies utilization 9 5.4 Packing products in pails 9 5.5 Packing products in bottles and jars. 9 5.5.1 Unit packing. 9 5.5.2 Intermediate packing 9 5.5.3 Commercial packing. 9
11、5.5.4 Exterior packing. 9 5.5.4.1 Level B. 9 5.5.4.2 Level C . 9 5.5.4.3 Commercial 10 5.6 Packing of specialty products. 10 5.6.1 Unit packing. 10 5.6.2 Exterior packing. 10 5.6.2.1 Level B. 10 5.6.2.2 Level C . 10 5.6.2.3 Commercial level 10 5.7 Packing of wax. 10 MIL-STD-290F vi CONTENTS PARAGRAP
12、H PAGE 5.7.1 Unit packing of 1-pound wax cakes. 10 5.7.2 Exterior packing. 10 5.7.2.1 Level B. 11 5.7.2.1.1 10- and 11-pound wax slabs. 11 5.7.2.1.2 Packing of solid wax 11 5.7.2.2 Level C unit packing of 1-pound wax cakes 11 5.7.2.2.1 Level C unit packing of 10- and 11-pound wax slabs 11 5.7.2.3 Co
13、mmercial level packing of solid wax. 11 5.8 Cleaner, lubricant, and preservative (CLP) 11 5.8.1 Unit packing container sizes of CLP 11 5.8.2 Exterior packing. 11 5.8.2.1 Level A. 12 5.8.2.2 Level C . 12 5.9 Exterior color coating of metal containers . 12 5.9.1 General. 12 5.9.1.1 Painting. 12 5.9.2
14、Hydraulic fluid 12 5.9.2.1 MIL-PRF-83282 - Hydraulic Fluid, Petroleum Base; Aircraft, Missile and Ordnance. 12 5.9.2.2 MIL-PRF-83282 - Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Metric, NATO Code No. H-537. 12 5.9.2.3 MIL-PRF-6083 - Hydraulic Fluid, Petroleum Base for Preservation
15、and Operation 12 5.9.2.4 MIL-H-46170 - Hydraulic Fluid, Rust Inhibited, Fire Resistant, Synthetic Hydrocarbon Base . 13 5.9.2.4.1 Type I 13 5.9.2.4.2 Type II 13 5.9.2.5 MIL-PRF-87257 - Hydraulic Fluid, Fire Resistant, Low. 13 Temperature, Synthetic Hydrocarbon Base, Aircraft and 5.9.2.5.1 Missile Ty
16、pe II. 13 5.9.2.6 Hermetically sealed cans 13 5.9.3 Synthetic lubricating oils 13 5.9.3.1 MIL-PRF-7808 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base 13 5.9.3.2 MIL-PRF-8188 - Corrosion Preventive Oil, Gas Turbine Engine, Synthetic Base. 13 5.9.3.3 MIL-PRF-23699 - Lubricating Oil, Aircra
17、ft Turbine Engine, Synthetic Base, NATO Code Number O-156 13 5.9.3.4 DOD-L-85734 - Lubricating Oil, Helicopter Transmission System, Synthetic Base 13 MIL-STD-290F vii CONTENTS PARAGRAPH PAGE 5.9.4 Petroleum lubricating oil 14 5.9.4.1 MIL-PRF-6081 - Lubricating Oil, Jet Engine 14 5.9.4.2 MIL-PRF-8725
18、2 - Coolant Fluid, Hydrolytically Stable, Dielectric 14 5.9.5 Brake fluid 14 5.9.5.1 SAE J 1703 - Motor Vehicle Brake Fluid 14 5.10 Marking 14 5.10.1 Marking of materials 14 5.10.2 Labels . 14 5.10.3 Color of markings. 14 5.10.4 Abbreviations . 14 5.10.5 Identification, contract data, and address ma
19、rkings . 15 5.10.5.1 Identification and contract data markings on unit containers of 1-gallon capacity or less. 15 5.10.5.2 Identification and contract data markings on unit and intermediate containers. 15 5.10.5.3 Identification, contract data, and address markings on drums . 16 5.10.5.4 Identifica
20、tion, contract data, and address markings of unit loads 16 5.10.6 Location and sequence of markings. 16 5.10.7 NATO code 16 5.10.8 Military symbol 16 5.10.9 Item description 16 5.10.10 Specification. 16 5.10.11 Type, class, and grade 16 5.10.12 National stock number (NSN) 16 5.10.13 Military airlift
21、 requirements. 17 5.10.14 Shelf life markings . 17 5.10.14.1 Date of manufacture. 17 5.10.15 Batch or lot number 17 5.10.16 Contract number. 18 5.10.17 Qualification number 18 5.10.18 Net contents 18 5.10.19 Regulatory marking and labeling . 18 5.10.20 Proper shipping name . 18 5.10.21 UN/NA identif
22、ication number 18 5.10.22 Other precautionary and statutory markings 18 5.10.23 Flash point and boiling point markings 18 5.10.24 Precautionary marking of hazardous and chemical materials 19 5.10.25 Unit of issue 19 5.10.26 Address marking. 19 5.10.26.1 Full carloads and full truckloads 19 5.10.26.2
23、 Less-than-carloads (LCL) and less-than-truckloads (LTL) 19 MIL-STD-290F viii CONTENTS PARAGRAPH PAGE 5.10.27 Gross weight. 19 5.10.28 Cube 19 5.10.29 Contractors name . 19 5.10.30 Returnable drums deposit marking. 19 5.10.31 Hazardous material data. 19 6. NOTES . 20 6.1 Intended use 20 6.2 Acquisit
24、ion requirements 20 6.3 Subject term (key word) listing 20 TABLE PAGE I Unit containers for petroleum and related products. 21 II Classification of cans and requirements for arrangement in interior and exterior packs 24 III Packing arrangement of tubes, bottles, and jars. 24 IV Markings on drums and
25、 pails for level B, C, and commercial. 25 V Identification and contract data marking on unit and intermediate containers (folding, setup, and fiberboard) 26 FIGURE PAGE 1 Marking of unit containers (one gallon or less) for level B shipment . 27 2 Marking unit and intermediate packs; levels B, C, and
26、 commercial 28 3 Marking of closed-head drums. 29 4 Marking of pails for levels B, C, and commercial. 30 5 Marking of fiberboard exterior packs (levels B, C, and commercial) 31 6 Marking palletized load for shipment of petroleum and related products 32 7 55-gallon drum palletization for DoD and othe
27、r government agencies utilization 33 8 55-gallon drum palletization design for four-way 40“x48“ pallets to provide stretch wrap bonding capabilities 34 MIL-STD-290F 1 1. SCOPE 1.1 Scope. This standard provides detailed requirements and approved uniform methods for packaging, packing, and marking of
28、petroleum and related products for shipment, handling and storage. 1.2 Application. 1.2.1 Centrally procured items. The level of protection, as well as any special marking requirements, should be incorporated in the appropriate purchasing documents. 1.2.2 Locally procured items. This standard is not
29、 mandatory for items locally procured for immediate use. 1.3 Options. Where options are indicated concerning methods of packaging or designation of the method is not specified in the contract or order, the selection should be at the option of the contractor. 2. APPLICABLE DOCUMENTS 2.1 General. The
30、following documents of the issues in effect on the date of invitation for bids or request for proposal form a part of this standard to the extent specified herein. 2.2 Government documents. 2.2.1 Specifications and standards. The following specifications and standards form a part of this standard to
31、 the extent specified herein. Unless otherwise specified, the issues of these documents should be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS), and the supplement thereto, cited in the solicitation. Unless otherwise indicated, the issues in ef
32、fect on the date of invitation for bids or request for proposal should apply. SPECIFICATIONS FEDERAL PPP-C-96 - Cans, Metal, 28 Gage and Lighter. PPP-C-186 - Containers, Packaging and Packing for Drugs, Chemicals, and Pharmaceuticals. PPP-P-704 - Pails, Metal: (Shipping, Steel, 1 through 12 Gallons)
33、. PPP-D-729 - Drums, Shipping and Storage, Steel, 55 Gallon (208 Liters). NN-P-71 - Pallets, Material Handling, Wood, Stringer Construction, 2-Way and 4-Way (Partial). MIL-STD-290F 2 DEPARTMENT OF DEFENSE MIL-PRF-2104 - Lubricating Oil, Internal Combustion Engine, Combat/Tactical Service. MIL-PRF-21
34、05 - Lubricating Oil, Gear, Multipurpose (Metric). MIL-H-5606 - Hydraulic Fluid, Petroleum Base; Aircraft, Missile and Ordnance. MIL-PRF-6081 - Lubricating Oil, Jet Engine. MIL-PRF-6083 - Hydraulic Fluid, Petroleum Base for Preservation and Operation. MIL-PRF-7808 - Lubricating Oil, Aircraft Turbine
35、 Engine, Synthetic Base. MIL-PRF-8188 - Corrosion-Preventive, Gas Turbine Engine, Synthetic Base. MIL-PRF-9000 - Lubricating Oil, Shipboard Internal Combustion Engine, High Output Diesel. MIL-PRF-17331 - Lubricating Oil, Steam Turbine and Gear, Moderate Service. MIL-PRF-17672 - Hydraulic Fluid, Petr
36、oleum, Inhibited. MIL-PRF-21260 - Lubricating Oil, Internal Combustion Engine, Preservative Break-In. MIL-PRF-23699 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Number O-156. MIL-H-46170 - Hydraulic Fluid, Rust Inhibited, Fire Resistant Synthetic Hydrocarbon Base. MIL-PRF-83
37、282 - Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Metric, NATO Code Number H-537. MIL-PRF-87252 - Coolant Fluid, Hydrolytically Stable, Dielectric. MIL-PRF-87257 - Hydraulic Fluid, Fire Resistant; Low Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile. DOD-L-85734 - Lubri
38、cating Oil, Helicopter Transmission System, Synthetic Base. STANDARDS FEDERAL FED-STD-313 - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities. FED-STD-595 - Colors Used in Government Procurement. DEPARTMENT OF DEFENSE MIL-HDBK-774
39、- Palletized Unit Loads. MIL-STD-290F 3 DEPARTMENT OF DEFENSE (continued) MIL-STD-2073-1 - Standard Practice for Military Packaging. (Unless otherwise indicated, copies of the above specifications and standards are available from the Standardization Documents Order Desk, 700 Robbins Avenue, Building
40、 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other government publications. The following other government publications form a part of this document to the extent specified herein. Unless otherwise indicated, the issues in effect on the date of invitation for bid or request for proposal should apply. CO
41、DE OF FEDERAL REGULATIONS (CFR) 29 CFR - Labor. 49 CFR - Transportation. (Application for copies should be addressed to the Superintendent of Documents, U.S. Government Printing Office, North Capital Aircraft, Missile and Ordnance. Containers of 1-gallon capacity or less and 10-gallon drums shall be
42、 coated RED, a color approximating Color No. 11105 or 21105 of FED-STD 595. Except for 10-gallon drums, containers larger than 1-gallon shall be coated TAN, approximating Color No. 22648 of FED-STD-595. Exterior tops and bottoms of cans shall not be coated. 5.9.2.2 MIL-PRF-83282 - Hydraulic Fluid, F
43、ire Resistant, Synthetic Hydrocarbon Base, Metric, NATO Code Number H-537. Containers of 1-gallon capacity or less shall be coated RED, a color approximating Color No. 11105 or 21105 of FED-STD-595. Containers larger than 1-gallon shall be coated TAN, approximating Color No. 22648 of FED-STD-595. Th
44、e exterior tops and bottoms of the cans shall not be coated. 5.9.2.3 MIL-PRF-6083 - Hydraulic Fluid, Petroleum Base for Preservation and Operation. Containers of 1-gallon capacity or less shall be coated RED, a color approximating Color No. 11105 or 21105 of FED-STD-595. Containers larger than 1-gal
45、lon shall be coated TAN, approximating Color No. 22648 of FED-STD-595. Five-gallon pails and 55-gallon drums shall have a WHITE band (approximately one inch wide) painted on the side directly below the top head chime. Exterior tops and bottoms of the cans shall not be coated. MIL-STD-290F 13 5.9.2.4
46、 MIL-H-46170 - Hydraulic Fluid, Rust Inhibited, Fire Resistant, Synthetic Hydrocarbon Base. 5.9.2.4.1 Type I. Containers of Type I hydraulic fluid shall be coated TAN, approximating Color No. 22648 of FED-STD-595. 5.9.2.4.2 Type II. Containers of Type II hydraulic fluid of 1-gallon capacity or less
47、shall be coated RED, a color approximating Color No. 11105 or 21105 of FED-STD-595. Containers larger than 1-gallon shall be coated TAN, approximating Color No. 22648 of FED-STD-595. In addition, 5-gallon pails and 55-gallon drums shall have a BLACK band (approximately one inch wide) painted on the
48、side directly below the top head chime. The exterior tops and bottoms of the cans shall not be coated. 5.9.2.5 MIL-PRF-87257 - Hydraulic Fluid, Fire Resistant; Low Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile. Containers of hydraulic fluid of 1-gallon capacity or less shall be coate
49、d RED, a color approximating Color No. 11105 or 21105 of FED-STD-595. Containers larger than 1-gallon shall be coated TAN, approximating Color No. 22648 of FED-STD-595. The exterior tops and bottoms of the cans shall not be coated. 5.9.2.6 Hermetically sealed cans. For all hydraulic fluid cans, contractors commercial hermetically sealed cans, 1-gallon capacity and smaller, may be used provided the container base color is red and all required markings are provided on the can. 5.9.3 Synthetic lubricating oils. 5.9.3.1 MIL-PRF-7808 - Lubricating Oil, Aircraft Turbine Engine, Synthetic