《NEMA-C136.33-2005.pdf》由会员分享，可在线阅读，更多相关《NEMA-C136.33-2005.pdf（9页珍藏版）》请在三一文库上搜索。
1、 ANSI C136.33-2005 American National Standard For Roadway and Area Lighting Equipment Plug-in Type Receptacle and Plug For High-intensity Discharge Ignitors Approved April 14, 2005 Secretariat: National Electrical Manufacturers Association An American National Standard implies a consensus of those s
2、ubstantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he has approved the standard or no
3、t, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. The American National Standards Institute does not develop stand
4、ards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute. CAUTION NOTICE: This American Nation
5、al Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of approval. Purchasers of American National Standards may receive curre
6、nt information on all standards by calling or writing the American National Standards Institute. Published by National Electrical Manufacturers Association 1300 North 17th Street, Rosslyn, VA 22209 Copyright 2005 by National Electrical Manufacturers Association All rights including translation into
7、other languages are reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American Copyright Conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or
8、 otherwise, without the prior written permission of the publisher. Printed in the United States of America DISCLAIMER: The standards or guidelines presented in a NEMA standards publication are considered technically sound at the time they are approved for publication. They are not a substitute for a
9、 product sellers or users own judgment with respect to the particular product referenced in the standard or guideline, and NEMA does not undertake to guarantee the performance of any individual manufacturers products by virtue of this standard or guide. Thus, NEMA expressly disclaims any responsibil
10、ity for damages arising from the use, application, or reliance by others on the information contained in these standards or guidelines. Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMALicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/
11、2007 09:44:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI C136.33-2005 2 CONTENTS 1 Overview .2 2 Normative references2 3 Informative references 3 4 Mechanical requirements3 5 Electrical and temperature requirements4 6 Mating requirements .4 7 Environmental require
12、ments.4 8 Safeguard and protective requirements4 9 Materials and finishes .4 Figures 1 Receptacle5 2 Plug.6 3 Connector socket7 4 Connector pin7 5 Limiting dimensions for ignitor 8 6 Receptacle connection diagram9 1 Overview 1.1 Scope This standard covers the physical features, dimensions, and elect
13、rical requirements of mating receptacles for plug-in type high-intensity discharge lamp ignitors used in roadway and area luminaires. The receptacle shall provide electrical connections so that it may be used for 52-, 55-, or 100-volt high- pressure sodium ignitors, either two-wire or three-wire, an
14、d also be used for metal halide ignitors. This standard does not cover the electrical and mechanical properties of the ignitor, except for the dimensions, electrical ratings, and characteristics of the plug that are necessary to ensure proper interface and compatibility with the receptacle. This sta
15、ndard is not intended to ensure electrical compatibility between manufacturers control components, but solely specifies the interface between luminaire and ignitor. 1.2 Interchangeability This receptacle shall be used when a universally interchangeable 9-pin ignitor receptacle is user specified and
16、shall not be otherwise required. This receptacle is intended for use only with ignitors rated as universal interchangeable ignitors or when specified by the ignitor manufacturer for use in a designated luminaire or group of luminaires. 2 Normative references This standard incorporates by undated ref
17、erence provisions from other publications. The normative references are cited at the appropriate places in the text, and the publications are listed below. For undated references, the latest edition of the publication referred to applies (including amendments). ANSI C136.2-2004, American National St
18、andard for Roadway and Area Lighting Equipment Luminaires Voltage Classification. UL 94, 1996, Standard for Tests for Flammability of Plastic Materials for Parts in Devices and Appliances. Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMALicensee=NASA Te
19、chnical Standards 1/9972545001 Not for Resale, 04/19/2007 09:44:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI C136.33-2005 3 3 Informative references This standard is intended to be used in conjunction with the following publications: (The latest edition of the pu
20、blication applies, including amendments.) ANSI C78, American National Standards for Electric Lamps. Series applicable documents. ANSI C82.4-2002, American National Standard for Ballasts for High-intensity Discharge and Low- pressure Sodium Lamps (Multiple Supply Types). ANSI C82.5-1995, American Nat
21、ional Standard for Reference Ballasts for High-intensity Discharge and Low-pressure Sodium Lamps. ANSI C82.6-1996, American National Standard for Ballasts for High-intensity Discharge Lamps Methods of Measurement. ANSI C82.9-1996, American National Standard for High-intensity Discharge and Low-press
22、ure Sodium Lamps, Ballasts, and Transformers Definitions. ANSI C136.11-1995, American National Standard for Roadway and Area Lighting Equipment Multiple Sockets. ANSI C136.19-2004, American National Standard for Roadway and Area Lighting Equipment High Pressure Sodium Lamps Guide for Selection. NOTE
23、 ANSI C136 Standards are available from Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112-5776 Phone: 303/397-7956, Fax 303/397-2740, e-mail: or . 4 Mechanical requirements 4.1 Receptacle The receptacle shall be of the 9-pin locking type. Its configuration and contacts shall
24、be as shown in Figure 1. 4.2 Plug The plug used in the ignitor shall be of the 9-pin locking type. Its configuration and contacts shall be as shown in Figure 2. The plug may be an integral part of the ignitor. 4.3 Sockets and pins The sockets used in the receptacle and the pins used in the plug are
25、shown in Figures 3 and 4, respectively. 4.4 Installation The receptacle shall be located so that when installed in any luminaire, its configuration and limiting dimensions will be in accordance with Figure 5. When installed in a luminaire, the receptacle location will permit a person wearing protect
26、ive gloves to easily remove and insert the ignitor without the use of tools. Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMALicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 09:44:37 MDTNo reproduction or networking permitted wi
27、thout license from IHS -,-,- ANSI C136.33-2005 4 5 Electrical and temperature requirements The receptacle and plug shall be rated for 600 volts as defined by ANSI C136.2. The receptacle shall be electrically connected in the luminaire as shown in Figure 6. The maximum operating temperature of the re
28、ceptacle and plug shall be 105C, including maximum temperature rise of the contact of 30C at 15 amperes. 6 Mating requirements Mating force shall not exceed 13.4 Newtons (48 oz). Minimum un-mating force, when unlatched, shall be 3.1 Newtons (11 oz). 7 Environmental requirements The receptacle and pl
29、ug shall operate over the ambient range of -40 to +105 C and shall pass the qualification tests described in clause 10. 8 Safeguard and protective requirements Electrical insulation between current-carrying components and any metallic portion of the ignitor enclosure or receptacle with its mounting
30、shall meet the dielectric withstand test requirements given for the 600-volt class in ANSI C136.2. 9 Materials and finishes 9.1 Resistance to atmospheric conditions Materials and protective coatings used in the construction of the ignitor plug, receptacle, and related components shall individually a
31、nd as a system be resistant to atmospheric conditions, including the corrosive and erosive action of conditions of service encountered in industrial and seaboard areas. 9.2 Long term service At a minimum, the materials used in the receptacle and ignitor plug shall be suitable for long-term service a
32、t 105C for both electrical and mechanical requirements. 9.3 Materials compatibility and flammability rating Materials shall be compatible with tin plated brass contacts and nylon housing. Housing material shall at least conform to the flammability rating of V-2 per UL 94 and be rated for 105C contin
33、uous. 9.4 Qualification test procedure The receptacle, with a 113 g (4 oz) ignitor installed, shall remain mated and function properly after a 3 g vibration test of 100,000 cycles is applied in each of three mutually perpendicular directions. Copyright National Electrical Manufacturers Association P
34、rovided by IHS under license with NEMALicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 09:44:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI C136.33-2005 5 Figure 1 Receptacle Copyright National Electrical Manufacturers Association Provided
35、by IHS under license with NEMALicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 09:44:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI C136.33-2005 6 Figure 2 Plug Copyright National Electrical Manufacturers Association Provided by IHS under l
36、icense with NEMALicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 09:44:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI C136.33-2005 7 Figure 3 Connector socket Figure 4 Connector pin Copyright National Electrical Manufacturers Association Pr
37、ovided by IHS under license with NEMALicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 09:44:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI C136.33-2005 8 Figure 5 Limiting dimensions for ignitor Copyright National Electrical Manufacturers A
38、ssociation Provided by IHS under license with NEMALicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 09:44:37 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI C136.33-2005 9 Figure 6 Receptacle connection diagram Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMALicensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 09:44:37 MDTNo reproduction or networking permitted without license from IHS -,-,-