《SAE-AS-172236-THRU-172270A-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-172236-THRU-172270A-2003-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 3 AS172236 THRU AS172270 REV. A THIRD ANGLE PROJECTION AEROSPACE STANDARD
3、AS172236 THRU AS172270 REV. A ISSUED 2000-08 REVISED 2003-03 REAFFIRMED 2007-06 (R) NUT, SPANNER, BEARING RETAINING, AERONAUTICAL, UNS G41400 PREPARED BY SAE COMMITTEE E-25, GENERAL STANDARDS FOR AEROSPACE & PROPULSION SYSTEMS FEDERAL SUPPLY CLASS 5310 FIGURE 1 - NUT RATIONALE THIS DOCUMENT HAS BEEN
4、 REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, witho
5、ut the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=D
6、efense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:55:23 MSTNo reproduction or networking permitted without license from IHS -,-,- NUT, SPANNER, BEARING RETAINING, AERONAUTICAL, UNS G41400 AEROSPACE STANDARDAS172236 THRU AS172270 SHEET 2 OF 3 AS172236 THRU AS172270 REV. A REV. A (R) TABLE 1
7、- PART NUMBERS AND DIMENSIONS Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:55:23 MSTNo reproduction or networking permitted without license from IHS -,-,- NUT, SPANNER, BEARING RETAINING, AERONAUTICAL, UNS G414
8、00 AEROSPACE STANDARDAS172236 THRU AS172270 SHEET 3 OF 3 AS172236 THRU AS172270 REV. A REV. A (R) TABLE 1 - PART NUMBERS AND DIMENSIONS (CONTINUED) NOTES: 1.MATERIAL: STEEL PER AMS 6381 OR AMS 6382 (UNS G41400). 2.HARDNESS: 26-32 HRC. HARDEN (OIL QUENCH) AND TEMPER. 3.MAGNETIC PARTICLE INSPECTION PE
9、R ASTM E 1444 AND AS5447. 4.SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 5.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 6.BREAK SHARP EDGES .000-.015, UNLESS OTHERWISE SPECIFIED. 7.DIME
10、NSIONS IN INCHES, UNLESS OTHERWISE SPECIFIED. 8.DO NOT USE UNASSIGNED PART NUMBERS. 9.THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) S
11、YMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. AS AND AMS ARE SOCIETY OF AUTOMOTIVE ENGINEERS, INC. PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN AMERICAN SOCIETY FOR TESTING AND MATERIALS PUBLICATION. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:55:23 MSTNo reproduction or networking permitted without license from IHS -,-,-